INSTALLATION INSTRUCTIONS FOR WHEELCHAIR LIFT MODEL NO. • WL7-vers. C • WL7-vers. C-1K DOT-Public Use Lift PATENTS PENDING FOR INSIDE VEHICLE INSTALLATION ONLY © MAXON Lift Corp. 2009 MP-06-09 REV.
PATENTS PENDING
THIS PAGE INTENTIONALLY LEFT BLANK PATENTS PENDING
TABLE OF CONTENTS INTRODUCTION ................................................................................................................... 6 SAFETY SUMMARY ............................................................................................................. 6 VEHICLE REQUIREMENTS ................................................................................................. 8 LIGHTING...........................................................................................................
FLOOR POSITION ADJUSTMENT (MANDATORY) .......................................................... 52 SYSTEM DIAGRAMS ......................................................................................................... 57 HYDRAULIC SYSTEM DIAGRAM ...................................................................................... 57 ELECTRICAL SYSTEM DIAGRAM ..................................................................................... 58 COMPLETED LIFT INSTALLATION CHECKLIST ...................
INTRODUCTION This manual contains instructions for installing the MAXON MOBILITY Wheelchair Lift in a transit vehicle. Please follow these instructions carefully and call us immediately if you need assistance with the installation. Do not take shortcuts, skip over installation steps, or modify the Lift. Correct installation is important to ensure the Lift operates correctly. If you have questions that are not covered in this manual, please contact: MAXON Lift Corp. - Customer Service 11921 Slauson Ave.
2. Before operating the Lift, read and understand the operating instructions contained in the Operator’s Manual. 3. Comply with all WARNING and instruction decals attached to both the Lift and the vehicle. 4. Keep decals clean and legible. If decals are illegible or missing, free replacement decals are available from MAXON Lift Corp. Customer Service. Refer to DECALS & DECAL PLACEMENT and the instructions for installing decals on vehicle in this manual. 5.
VEHICLE REQUIREMENTS 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 The minimum vehicle requirements for installing the WL7 Wheelchair Lift are described below. Installing the Lift in accordance with the vehicle requirements and the instructions in this manual will result in an installation that is compliant with Federal Motor Vehicle Safety Standard (FMVSS) 403 and FMVSS 404. M F BODY STRENGTH ! WARNING FORCE & MOMENT PRODUCED BY LIFT ON VEHICLE FLOOR FIG.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 ELECTRICAL POWER Vehicle must have a 12 volt dc electrical system capable of supplying 65 amperes of electrical power to the Lift for each operating cycle. SAFETY INTERLOCK SYSTEM Vehicle must have an FMVSS 403 compliant, onboard Safety Interlock System that interfaces with the Wheelchair Lift interlock signal. Interlock signal may be V+ or V-.
VEHICLE REQUIREMENTS - Continued WHEELCHAIR DOOR DIMENSIONS A 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 B WHEELCHAIR DOOR DIMENSIONS ON TYPICAL VEHICLE WITH SIDE DOOR (SEE TABLE 10-1) FIG.
LIFT DIMENSIONS D 13.3” 2.9” 1.4” 55.13” 0.5” 39” 25” E 4.75” 18-3/4” F FRONT VIEW OF STOWED LIFT (LH PUMP MODEL SHOWN) (SEE TABLE 11-1) FIG. 11-2 SIDE VIEW OF STOWED LIFT (LH PUMP MODEL SHOWN) FIG.
VEHICLE REQUIREMENTS - Continued 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 WHEELCHAIR DOOR 18-3/4” (APPROX.) 0.75” (MIN.) 48”(MAX.) WHEELCHAIR DOOR CLEARANCE & FLOOR HEIGHT ON TYPICAL VEHICLE WITH SIDE DOOR FIG.
6.75” (46” FLOOR LEVEL - REF) 8.75” (44” FLOOR LEVEL - REF) 10.25” (42” FLOOR LEVEL - REF) BASE PLATE OUTBOARD EDGE (REF) TYPICAL VEHICLE REAR BUMPER (VAN GND LVL) (BUS GND LVL) (BUS GND LVL) BODY CLEARANCE POINTS: 32”, 40”, 42”, 46” & 48” FLOOR HEIGHTS FIG. 13-1 13 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 3.
LIFT COMPONENTS & TERMINOLOGY 10 INBOARD 6 RIGHT 4 11 10 6 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 7 8 12 5 9 LEFT 1 12 3 LIFT COMPONENTS (SEE TABLE 13-1) FIG.
2. OUTBOARD ROLLSTOP 3. PLATFORM 4. HANDRAILS 5. INBOARD ROLLSTOP 6. HYDRAULIC CYLINDER 7. HYDRAULIC POWER UNIT (COVER IS SHOWN) LIFT CONTROLLER (BRAIN BOX) 8. 9. BASE 10. THRESHOLD WARNING BEACON 11. THRESHOLD WARNING ALARM 12. PLATFORM LIGHTS DESCRIPTION Component that bridges the entry way, through the Lift, into the vehicle. Detects if that portion of Lift is occupied during “UP/DOWN” operation between vehicle floor and the ground.
DECALS AND DECAL PLACEMENT DECAL ”D” DECAL “O” DECAL “K” DECAL “A” DECAL “B” 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECAL “F” DECAL “L” DECAL “M” DECAL “I” DECAL“J” DECAL“N” DECAL “C” DECAL “E” DECAL“N” DECAL “H” FIG. 16-1 All WARNING, CAUTION, and OPERATION decals provided with Wheelchair Lift must always be in place on the Lift and vehicle (see FIG. 36-1), and must always be legible.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECALS FOR WL7-vers. C DECAL SET P/N 268302-01 FIG.
DECALS AND DECAL PLACEMENT - Continued DECALS FOR WL7-vers. C-1K 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECAL SET P/N 268302-03 FIG.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 SERIAL PLATE & CONTROLLER CONTROLLER OVERLAY P/N 2667630-01 FIG. 19-1 SERIAL PLATE P/N 905246-8 FIG.
ANTI-SLIP & SAFETY STRIPING (30” WIDE PLATFORM) YELLOW TAPE (BOTTOM-ROLLSTOP) P/N 905293-17 11921 Slauson Ave. Santa Fe Springs, CA.
ANTI-SLIP & SAFETY STRIPING - Continued YELLOW TAPE (BOTTOM-ROLLSTOP) P/N 905293-18 ANTI-SLIP TAPE (ROLLSTOP) P/N 096020-14 ANTI-SLIP TAPE P/N 096024-11 ANTI-SLIP TAPE P/N 096020-11 ANTI-SLIP TAPE P/N 096013-11 YELLOW TAPE (OUTBOARD) P/N 905293-11 YELLOW TAPE (OUTBOARD) P/N 905293-14 ANTI-SLIP TAPE (ROLLSTOP) P/N 096020-14 YELLOW TAPE P/N 905293-11 YELLOW TAPE (INBOARD) P/N 905293-16 YELLOW TAPE P/N 905293-14 YELLOW TAPE (INBOARD & OUTBOARD) P/N 905293-15 FIG.
ANTI-SLIP & SAFETY STRIPING - Continued (34” WIDE PLATFORM) 11921 Slauson Ave. Santa Fe Springs, CA.
LIFT INSTALLATION An installation kit is required to install Lift on your vehicle. Refer to the instruction sheet, included with the installation kit, for specific instructions to fit the Lift to your vehicle. PREPARING AND POSITIONING THE LIFT 1. Make sure you have the correct model of Lift. NOTE: Keep shipping straps on Lift until Lift is bolted to vehicle and power is connected. 2. Unpack the Lift and check for damage. Report damage to: MAXON Lift Corp. - Customer Service 11921 Slauson Ave.
PREPARING AND POSITIONING THE LIFT - Continued NOTE: You may use a template instead of the Lift for positioning the Lift on vehicle. To use a template, refer to USING TEM PLATE TO POSITION LIFT section in this Installation Manual. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 5. Using an appropriate lifting device that can safely lift 500 pounds, raise Lift to the wheelchair doorway. Place the Lift inside doorway (FIG. 24-1).
1. Fabricate template for base plate hole pattern according to the dimensions shown in FIGS. 25-1, 25-2, 26-1 and 26-2. Use a suitable material that maintains correct shape and dimensions. BASE PLATE HOLE PATTERN FOR LIFTS WITH 33” & 34” WIDE PLATFORMS & RH PUMP FIG. 25-1 BASE PLATE HOLE PATTERN FOR LIFTS WITH 33” & 34” WIDE PLATFORMS & LH PUMP FIG. 25-2 25 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
USING TEMPLATE TO POSITION LIFT - Continued 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 BASE PLATE HOLE PATTERN FOR LIFTS WITH 30” WIDE PLATFORM & LH PUMP FIG. 26-1 BASE PLATE HOLE PATTERN FOR LIFTS WITH 30” WIDE PLATFORM & RH PUMP FIG.
For vehicles with 48” floor height: If the front edge of Lift base plate is moved more than 3.75” (5” from outside of body, as shown in FIG. 11-1) away from the inside of the wheelchair door, lower Lift arms can hit vehicle body before platform reaches the ground. See the vehicle floor levels plotted in FIG. 11-1 and maintain the clearance for the floor level that applies to your Lift installation. 2. Center the template inside wheelchair doorway (FIG. 27-1).
MOUNTING THE LIFT NOTE: MAXON recommends using all 10 carriage screws (Kit items) to bolt Lift to vehicle. A minimum of 8 screws or bolts and use of holes 1, 2, 3, 4 & 9 are required for correct installation. Also, the 3 front holes should be selected to give a symmetrical bolt pattern (i.e. holes 5,10, & 8 or holes 6,10, & 7). 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Use template (FIG. 27-1) or the base plate on the Lift (FIG.
! WARNING To prevent personal injury and equipment damage, make sure power is disconnected from Lift when installing electrical parts. NOTE: Apply dielectric grease on all electrical connections after all electrical cables are connected. 1. Attach 90 amp main circuit breaker (Kit item) to vehicle so power cable (Kit item) is within reach of the battery, as follows. Find a place to attach bracket (FIG. 29-1).
INSTALL MAIN CIRCUIT BREAKER - Continued 2. Connect one end of power cable to 90 amp main circuit breaker (FIG. 30-1). Do not connect battery end until instructed to connect the battery. 1/4” FLAT WASHER (2 PLACES) BATTERY 11921 Slauson Ave. Santa Fe Springs, CA.
! CAUTION Never route an energized wire. Make sure the battery is disconnected. Always route electrical wire clear of any moving parts, brake lines, sharp edges, and exhaust systems. Never route power cable next to a wiring harness on the vehicle. Do not loop excess cable. Cut the cable to fit and leave slack. Attach securely. If drilling is necessary, be sure to check underside of vehicle before drilling so you do not damage any fuel lines, vent lines, brake lines or wires.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued POWER INPUT BRACKET 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 4. Cut any excess wire from long power cable. Strip 1/2” insulation from the cut end and install 2 GA terminal lug and shrink tubing. Next, insert the power cable through the protective cover (FIG. 32-1). Connect the TERMINAL cable terminal to the terminal stud on the STUD power input bracket as shown in FIG. 321.
GROUND CABLE GROMMET NOTE: Clean the ground cable connection point on the frame down to bare metal. NOTE: If there is a grounding point on the frame, use it to connect ground cable. Skip step 8. NOTE: Apply dielectric grease to all electrical connections. GROUND CABLE ROUTED FROM LIFT FIG. 33-1A BARE METAL TERMINAL LUG 3/8”-16 X 1” LG. CAP SCREW VEHICLE FRAME 8. Extend the ground cable to reach vehicle frame (FIG. 33-2). Connect to an existing grounding point if available.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued ! CAUTION To prevent vehicle access door from pinching and damaging the hand pendant cable, secure cable away from the door frame. Also, be sure that the hand pendant cable does not interfere with or bind against moving parts. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 10. Connect the hand pendant cable as follows. Feed the cable through the hole located in the main frame (FIG. 34-1).
HAND PENDANT & HANGER CABLE HOOK PUMP COVER TYPICAL LOCATION (INSIDE VEHICLE) FOR STOWING HAND PENDANT FIG. 35-1 35 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 11. Find accessible place on vehicle wall or wheelchair door (near Lift) to place the hand pendant hanger and cable hook (FIG. 35-1).
ROUTE/CONNECT CABLES & HAND PENDANT - Continued 12. Place decals (from Parts Box) on the vehicle, near the hand pendant (typical placement shown in FIG. 36-1). Make sure decals are visible to operator when Lift is being operated. HAND PENDANT & HANGER MOUNTING DECAL “J” DECAL “I” 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECAL “A” DECAL “C” DOOR DECAL “B” CABLE HOOK DECAL “A” P/N 268303-01 DECALS AND HAND PENDANT MOUNTING ON VEHICLE FIG.
POSITIVE (+) BATTERY TERMINAL SHORT POWER CABLE BOLT NUT CONNECTING POWER TO LIFT (TYPICAL) FIG. 37-1 POWER ON/OFF SWITCH 14. Turn ON power ON/OFF switch on pump cover to power the Lift (FIG. 37-2). The POWER light on hand pendant should be illuminated (FIG. 37-3). Briefly press the FOLD button on hand pendant (FIG. 37-3) to pressurize hydraulic system. Then, remove remaining shipping straps. STOWED LIFT - LH SIDE SHOWN FIG. 37-2 UP FOLD FOLD UNFOLD POWER LIGHT HAND PENDANT FIG.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued 15. Press the UNFOLD button on hand pendant to unfold Lift (FIG. 381). Platform lights will turn on when platform is at floor level. PLATFORM LIGHT (2 PLACES) 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 LIFT AT FLOOR LEVEL FIG. 38-1 16. Next, press DOWN button on hand pendant. When the platform reaches the ground, the outboard rollstop will automatically open to ramp position (FIG. 38-2).
CHECKING HYDRAULIC FLUID LEVEL Keep dirt, water and other contaminants from entering the hydraulic system. Before opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, wipe off contaminants that can get in the openings. Also, protect the openings from accidental contamination. 1. Check the hydraulic fluid level in reservoir as follows. With Lift in STOWED position, fluid level should be as shown in FIG. 39-1.
CHECKING HYDRAULIC FLUID LEVEL - Continued 3. Pull out filler cap (FIG. 40-1). Fill the reservoir with hydraulic fluid (TABLE 40-1) to level shown in FIG. 40-1. Reinstall filler cap (FIG. 40-1). 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 RECOMMENDED HYDRAULIC FLUID BRAND PART NUMBER ROSEMEAD THS FLUID 17111 EXXON UNIVIS HVI 26 FILLER CAP RESERVOIR TABLE 40-1 2” NOTE: If the expected seasonal temperatures are below 20°F, use MIL-H-5606G hydraulic fluid.
11921 Slauson Ave. Santa Fe Springs, CA.
ADJUSTMENTS MAT SWITCH ADJUSTMENT (IF REQUIRED) 1. Make sure power switch (FIG. 42-1A) is turned on. Lower Lift to the ground (FIG. 421A). POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 5/8” HEIGHT MEASUREMENT (RH SIDE SHOWN) FIG. 42-1B LIFT AT GROUND LEVEL FIG. 42-1A 2. Measure the height of the threshold plate as shown in FIG. 42-1B. If the height is 5/8”, go to step 4 (skip step 3). If the height is not 5/8”, go to step 3. LIFT THRESHOLD FIG.
THRESHOLD WARNING BEACON THRESHOLD WARNING ALARM BASE PLATE ADJUSTMENT SCREW THRESHOLD PLATE ADJUSTING SWITCH FIG. 43-1B LH SIDE OF LIFT FIG. 43-1A CW - UNTIL ALARM & BEACONS TURN ON 1-1/2 TURN CCW - ALARM & BEACONS TURN OFF MAT SWITCH ADJUSTMENT SCREWS FIG. 43-2 5. Step on threshold plate. Warning alarm and beacons should activate. If the warning alarm and beacons do not activate, slightly turn adjustment screw (FIGS. 43-1B and 43-2) clockwise.
PLATFORM TILT ADJUSTMENT (MANDATORY) NOTE: The platform tilt adjustment is important for operation of the outboard rollstop and for keeping platform level when it reaches the ground. Vehicle floor height, Lift and stiffness of the vehicle suspension may change the angle of platform on the ground. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Make sure power switch (FIG. 44-1) is turned on. Lower the platform and stop approximately 4” above ground.
CW - PLATFORM TILT UP CCW - PLATFORM TILT DOWN PLATFORM TILT ADJUSTMENT SCREWS FIG. 45-2 45 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 OUTBOARD ROLLSTOP 4. Manually lower the inboard ADJUSTMENT (REF) rollstop for access to the adSCREW justment screws (FIG. 45-1). To ensure proper leveling, turn platform tilt adjustment screws (FIG. 45-1) an equal amount on both sides of platform. Turn adjustment screws clockwise (FIG.
INBOARD SWITCH ADJUSTMENT (IF REQUIRED) NOTE: Do this procedure if the Controller reads “IBRS SW” when Inboard Rollstop is locked in the up position. The adjustment is done correctly if the Controller does not read “IBRS SW” when the Inboard Rollstop is locked in the up position. POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Position the platform at floor level (FIG. 46-1). PLATFORM AT FLOOR LEVEL (LH SIDE SHOWN) FIG. 46-1 2.
IBRS PUSH IBRS AGAINST LOCK PLATFORM BELOW FLOOR LEVEL, WITH IBRS UP (LH SIDE SHOWN) FIG. 47-1 5. On the inboard rollstop switch, loosen screws (1) and (2) one-half turn (FIG. 47-2B). Next, rotate switch bracket clockwise until the switch activates with an audible “click”. Then tighten screws (1) and (2) securely. SCREW (2) SCREW (1) SWITCH (REF) SWITCH BRACKET POWER SWITCH 6. Turn ON power switch on pump cover (FIG. 47-2A). Then raise (UP) the platform to floor level (FIG. 46-1).
CHANGING CONTROLLER TO SPANISH OR ENGLISH (IF REQUIRED) NOTE: The power switch on the Lift must be turned OFF before entering SETUP. UP FOLD 1. Turn power switch OFF (FIG. 48-2). 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 HAND PENDANT: ENTERING SETUP FIG. 48-1 POWER SWITCH CONTROLLER (REF) 2. Enter SETUP by holding both the UP and FOLD switches on the hand pendant (FIG. 48-1) and turning the power switch ON at the same time (FIG. 48-2).
FOLD HAND PENDANT: CHANGING SETUP MODE FIG. 49-1 LANGUAGE: ENGLISH CONTROLLER: LANGUAGE SETTING (ENGLISH OR SPANISH) FIG. 49-2 NOTE: After you exit SETUP, the controller readings will be displayed in the language you selected. 4. Push the UP switch or DOWN switch to change from ENGLISH to SPANISH (or from SPANISH to ENGLISH) (FIGS. 49-2 and 49-3). UP DOWN HAND PENDANT: CHANGING THE SETTING FIG. 49-3 5. Push and release the FOLD switch (FIG. 49-1) three times to exit SETUP (FIG. 49-4).
OUTBOARD ROLLSTOP TIME ADJUSTMENT (IF REQUIRED) NOTE: Call MAXON Technical Service before doing this adjustment. UP FOLD NOTE: The power switch on the Lift must be turned OFF before entering SETUP. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Turn power switch OFF (FIG. 50-2). HAND PENDANT: ENTERING SETUP FIG. 50-1 POWER SWITCH CONTROLLER (REF) 2. Enter SETUP by holding both the UP and FOLD switches on the hand pendant (FIG.
FOLD HAND PENDANT: CHANGING SETUP MODE FIG. 51-1 NOTE: A larger number for the OUTBD TIME setting allows more time for the controller to sense the outboard rollstop is closed. A smaller number decreases the time. Call MAXON Technical Service to advise you about the best setting for your vehicle. OUTBD TIME: 0 CONTROLLER: SETTING OUTBOARD RAMP TIME (RANGE IS -7 TO 10) FIG. 51-2 4. Push the UP switch (FIG. 51-3) to increase the OUTBD TIME from -7 to 10. Push the DOWN switch (FIG.
FLOOR POSITION ADJUSTMENT (MANDATORY) NOTE: Do the following procedure to ensure the inboard rollstop rests on threshold plate and lines up approximately with edge of base plate. 1. Unfold the platform until the lights illuminate at floor level or raise the platform to floor level as shown in FIG. 52-1A. 11921 Slauson Ave. Santa Fe Springs, CA.
THRESHOLD PLATE EDGE OF INBOARD ROLLSTOP EDGE OF BASE PLATE INBOARD ROLLSTOP OVERLAPS EDGE OF BASE PLATE FIG. 53-1 THRESHOLD PLATE EDGE OF INBOARD ROLLSTOP EDGE OF BASE PLATE INBOARD ROLLSTOP WITH GAP BETWEEN BASE PLATE FIG. 53-2 NOTE: The power switch on the Lift must be turned OFF before entering SETUP. POWER SWITCH 4. Turn power switch OFF (FIG. 53-3). CONTROLLER (REF) TURNING POWER SWITCH ON/OFF (LH PUMP SHOWN) FIG. 53-3 53 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
FLOOR POSITION ADJUSTMENT - Continued 5. Enter SETUP by holding both the UP and FOLD switches on the hand pendant (FIG. 54-1) and turning the power switch ON at the same time (FIG. 533). Controller will read SETUP (FIG. 54-2). UP FOLD 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 HAND PENDANT: ENTERING SETUP FIG. 54-1 SETUP CONTROLLER: ENTERING SETUP FIG. 54-2 6. Push and release the FOLD switch (FIG. 54-3) two times to access the FLOOR POS setting (FIG. 54-4).
DOWN (-) HAND PENDANT: CHANGING THE SETTING FIG. 55-1 FLOOR POS: 350 CONTROLLER: SETTING FLOOR POSITION (EXAMPLE READING SHOWN) FIG. 55-2 8. Push and release the FOLD switch (FIG. 55-3) to exit SETUP (FIG. 55-4). FOLD HAND PENDANT: CHANGING SETUP MODE FIG. 55-3 MAXON LIFT CORP. CONTROLLER: EXITING SETUP FIG. 55-4 55 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 UP 7. To decrease overlap, push the UP switch from 1 to 5 times (FIG. 55-1).
FLOOR POSITION ADJUSTMENT - Continued 9. Lower the platform until the inboard rollstop is in the up and locked position. Next, raise the platform to floor level (FIG. 56-1A). Verify that the inboard rollstop lines up with the edge of the base plate as shown in FIG 56-1B. If necessary, repeat this entire procedure. THRESHOLD PLATE INBOARD ROLLSTOP 11921 Slauson Ave. Santa Fe Springs, CA.
SYSTEM DIAGRAMS FLOW CONTROL VALVE - .5 GPM FLOW CONTROL VALVE - .5 GPM PRESSURE TRANSDUCER CYLINDER CYLINDER PRESSURE PORT PRESSURE PORT MANUAL RELEASE VALVE S.V.1 .018 DIA. S.V.2 MANUAL BACK-UP PUMP RETURN RETURN GEAR PUMP R.V. SET @ 1550 PSI FILLER BREATHER FIG. 57-1 57 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
SYSTEM DIAGRAMS - Continued ELECTRICAL SYSTEM DIAGRAM 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 FIG.
COMPLETED LIFT INSTALLATION CHECKLIST parking brake. If equipped with locking service brake, set the service brake and make sure vehicle is in park or neutral. Start vehicle engine. Turn on Wheelchair Lift power switch (if equipped) at the vehicle driver’s station. If equipped, make sure occupant restraint belt is buckled on Lift. Make sure Lift is stowed. 2. Turn ON power switch at the Lift. Record CYCLE COUNT _________ and LIFT COUNT _________ indicated on Lift controller.
8. Make sure platform lowers all the way to the ground and platform lights are illuminated while platform is lowering. Press DOWN button on the hand pendant to lower platform to the ground. As the platform is lowering: • Controller must display DOWN • Platform lights must be illuminated When the platform reaches the ground: • Controller must display GROUND • Outboard rollstop must lower to the ground 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 9.
