User manual

Toolbox 32 User Manual 1.47d www.cse-semaphore.com/mykingfisher
Page
27
IO Wiring
IO POWERED BY LP-2/3 IO POWERED EXTERNALLY
ANALOG INPUTS* (0-20 or 4-20 mA) ANALOG INPUTS* (0-20 or 4-20 mA)
GND
AO VOLTAGE
AI CH 1
AI CH 4
AI CH 2
AI CH 3
GND / 0V
AO CURRENT
AOV
AOC
ANALOG OUT
ANALOG INPUTS
AI4
AI3
AI2
AI1
AI CH x
24V OUT
GND / 0V
AI CH x
+
-
GND / 0V
AI CH x
PWR
250
GND / 0V
+
-
Analog 3
-
wire
transmitter
250
+
-
250
PWR
24V OUT
24V OUT
Analog 4
-
wire
transmitter
Analog 2
-
wire
transmitter
+
-
AI CH x
GND / 0 V
PWR
POWER
SUPPLY
+
-
+
-
AI CH x
GND / 0 V
PWR
+
-
AI CH x
GND / 0 V
+
-
+
-
250
250
250
POWER
SUPPLY
POWER
SUPPLY
Analog 3
-
wire
transmitter
Analog 4
-
wire
transmitter
An
alog 2
-
wire
transmitter
ANALOG OUTPUT (LP-3 only) ANALOG OUTPUT (LP-3 only)
24V OUT
AO CURRENT
+
-
Analog
Current Load
AO VOLTAGE
+
-
GND / OV
Analog
Current Load
AO CURRENT
-
GND / OV
POWER
SUPPLY
+
Analog
Current Load
+
DIGITAL OUTPUTS
#
DIGITAL OUTPUTS
#
DI / PULSE
CP5V DI2 DI1
DO6 DO5 DO4 DO3
RELAY 2
RELAY 1
2A 2B 1A 1B
GND
DO CH 2
DI CH 7/DO CH 5
DI CH 5/DO CH 3
DO CH 1
DI CH 6/DO CH 4
DO CH 1 COM.
DI CH 1
DI CH 4
DI CH 2
DI CH 3
DO CH 2 COM.
GND / 0V
CPU 5V OUT
DI CH 8/DO CH 6
5V DI8 DI7 DI6 DI5 DI4 DI3
5V OUT
24V OUT
LOAD
DO CH 1 or 2
-
+
DO CH 1 or 2
COM.
GND / 0V
LOAD
-
+
Relay
Output
Transistor
Output
(optional)
24V OUT
DO CH 3 to 6
LOAD
DO CH 1 or 2
-
+
DO CH 1 or 2
COM.
+
DO CH 3 to 6
Relay
Output
+
POWER
SUPPLY
-
LOAD
-
Transistor
Output
(optional)
GND /
0
V
POWER
SUPPLY
DIGITAL INPUTS DIGITAL INPUTS
FIELD CONTACT
DI CH 1 or 2
CPU 5V OUT
FIELD CONTACT
DI CH x
5V OUT or
24V OUT or
VDC1 OUT
Pulse
Counting in
Subactive
Sleep Mode^
DI CH x
+
FIELD CONTACT
POWER
SUPPLY
GND / 0V
* When using a 0-5 V or 1-5 V analog input, the external 250 Ω resistor is not required. Unused inputs should be tied to
GND / 0V to prevent spurious readings. 0-5 or 0-20mA is the default analog input range. 1-5 or 4-20mA is software
configurable.
#
DI Channels 5 to 8 can be software configured as transistor digital outputs. When the output is energised, the output is
shorted to the OV terminal.
^
CPU 5V Out stays enabled during power down modes and can only be used with DI1 and DI2 to wake the RTU or to
count pulses while remaining asleep. Note: CPU 5V Out is not isolated.