User manual

Toolbox 32 User Manual 1.47d www.cse-semaphore.com/mykingfisher
Page
260
LP-1/2/3 Hardware Setup Registers
Register Description Default Comments Read/Write
#DI1.9 LP-1: Port 3 Status 0 LP-1: 1 = port 3 configured
LP-2/3: Not used.
Read
#DI1.10 LP-1: Port 4 Status
LP-2/3: Port 3 or Port 4 detected
0 LP-1: 1 = port 4 configured
LP-2/3: 1 = one or two option
ports detected
Read
#DO1.13 Pulse input 1 enable 0 (LP-1)
1 (LP-2/3)
1 = enabled. Also allows wakeup
via DI1
Read/Write
#DO1.14 Pulse input 2 enable 0 (LP-1)
1 (LP-2/3)
1 = enabled. Also allows wakeup
via DI2
Read/Write
#DO1.15 Pulse input 1 active transition 0 0 = low to high transition
1 = high to low
Read/Write
#DO1.16 Pulse input 2 active transition 0 0 = low to high transition
1 = high to low
Read/Write
#DO2.7 DO3 enable 0 0 = DO3 disabled & DI5 enabled Read/Write
#DO2.8 DO4 enable 0 0 = DO4 disabled & DI6 enabled Read/Write
#DO2.9 DO5 enable 0 0 = DO5 disabled & DI7 enabled Read/Write
#DO2.10 DO6 enable 0 0 = DO6 disabled & DI8 enabled Read/Write
DO2.11
LP-1: 12 V Out enable
LP-2/3: VDC1 Out enable
0 (LP-1)
1 (LP-2/3)
LP-1: 0 = 12V Out Disabled. 12V
Out is used to power a port 3 Trio
radio if installed.
LP-2/3: 1 = VDC1 Out enabled
Read/Write
DO2.12
I/O, 5V Out (LP-1/2/3) and 12V
Aux (LP-1) disable
0
0 = I/O, 5V Out and 12V Aux
(LP-1) enabled. When set (=1):
• Switches off 5V Out and 12V
Aux (LP-1)
• Stops updating analog and
digital inputs
• Digital inputs 1 & 2 still
operate
• Digital outputs 1 & 2 still
operate
•
Disables power to ports 3 and
4 (LP-2/3)
Note 1: I/O and 5V Out must be
enabled for low voltage shutdown
to operate correctly (allows
reading of the supply voltage)
Note 2: 5V Out is used to power
a port 3 internal GSM if installed
(LP-1).
Note 3: CPU 5V Out remains
enabled
Read/Write
DO2.13 LP-1: Port 3 disable
LP-2/3: VDC2 Out enable
1 LP-1: 1 = Port 3 disabled
LP-2/3: 1 =VDC2 Out enabled
Read/Write
DO2.14 LP-1: Port 4 disable
LP-2/3: Port 3 and Port 4
disable
1 (LP-1)
0 (LP-2/3)
LP-1: 1 = Port 4 disabled
LP-2/3: 0 = Port 3 and Port 4
enabled
Read/Write
#AO5.5 Pulse Output count 0 Uses DO Ch3 (must be enabled) Read/Write
#AO5.6 Pulse ON time 0 x 1ms Read/Write
#AO5.7 Pulse OFF time 0 x 1ms Read/Write
#DO6.1 Analog input 1 live zero 0 0=0-5 V, 1=1-5 V Read/Write