Specifications

A Remote Automated Water Quality Stream Gauging System Design 23
23
11. Check all codes are entered correctly (Should be exactly the same as the codes below if using
Telsra)
AT&V
&C: 1; a&D: 2; &F: 1; &W: 1; E: 0; L: 0; M: 0; Q: 1; V: 1; X: 0; Z: 0;
S0: 2; S3: 13; S4: 10; S5: 8; S6: 2; S7: 50; S8: 2; S9: 6; S10: 14;
S11: 95; +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 9600; +DR: 0;
+DS: 0,0,2048,6; +WS46: 12; +CBST: 7,0,1;
+CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
+CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0; +CGREG: 0;
+CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 2; +CGDCONT: (1,"IP","
","",0,0),(2,"IP","telstra.internet","",0,0),(3,"IP","telstra.pcpack","",0,0),(4
,"IP","telstra.datapack","",0,0)
; +CGDSCONT: ; +CGTFT: ; +CGEQREQ: ; +CGEQMIN: ; +CGQREQ: ; +CGQMIN: ;
+CGEREP: 0,0; +CGDATA: "PPP"; +CGCLASS: "B"; +CGSMS: 1; +CSMS: 0;
+CMGF: 1; +CSCA: "",; +CSMP: ,,0,0; +CSDH: 0; +CSCB: 0,"",""; +FDD: 0;
+FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,; +ESA: 0,,,,0,0,255,; +CMOD: 0;
+CVHU: 1; +CPIN: , ; +CMEC: 0,0,0; +CKPD: 1,1; +CGATT: 1;
+CGACT: 0; +CPBS: "SM"; +CPMS: "ME","ME","ME"; +CNMI: 2,1,0,0,0;
+CMMS: 0; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM: 96; +FRM: 96;
+CCUG: 0,0,0; +COPS: 0,0,""; +CUSD: 0; +CAOC: 1; +CCWA: 0;
+CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CTZU: 0; +CLIP: 0; +COLP: 0;
+CDIP: 0
Iridium Satellite Modem
1. Enter the following AT Commands in sequence
a. AT&F (Restores your factory default settings) – You will get a response of OK
b. AT+IPR=5 (Sets the baud rate to 9600) – You will get a response of OK
c. ATS0=1 (Tells the modem to answer after 1 ring) – You will get a response of OK
d. ATE0 (Turns off ECHO) – You will get a response of OK, Note you will not be able to
see what you are typing from now on.
e. ATQ1 (Turns off Response codes) – You will get no response because you just turned
response codes off!
f. AT&W (Saves your configuration) – No response
2. You can now check your registers by typing AT&V please make sure your registers read what you
just entered and that the registers also read the same under the PROFILE 0 heading eg…
E: 0
Q: 1
S0: 1
3. You should now be connected to the Iridium Network, this can be confirmed by typing:
AT+CREG
If you get a response of 000,001 the satellite modem is connected to the Iridium network