Downloaded from www.cbradio.
User Manual CM10 Contents Specification………………………………………………………………………………………………………………………3 Control and Operation ……………....……………………………………………………………………………………4-5 Installation …………………………………………………………………………………………………………………………6 Installation of Main Unit ………………………………………………………………………………………………………6 Installation of Antenna ……………………………………………………………………………………………………….
User Manual CM10 Specification GENERAL Channels…………………………………………………..……...……………………………......…. 40 Ch AM/FM 4W Frequency Range………………………………...………………………………………..….26.565 to 27.99125 MHz Frequency Control……………………………………………………..……………………………………………….……PLL Operating Temperature Range……………………..…………………………………………..…….….-10° / +55°C DC Input Voltage…………………………...…………………...…………………………………….…13.2 V DC ±15% Size………………………………………….………………………………………...…….180(L) X 35(H) X 140(D) mm Weight…………………………………………………………...……………………………………………………..
User Manual CM10 Control & Operation Front Panel 1. AM/FM Selector This key allows the user to select the AM or FM operating mode in both RX and TX. The AM/FM operating mode selection is possible only if it is enabled on the programmed frequency band. 2. CH9/CH19 Selector This key allows quick access to one of the two pre-programmed emergency channels (CH9 and CH19). Each time this key is pressed, the radio will select CH9, then CH19, then again the normal operating channel.
User Manual CM10 9. OFF / VOLUME Control Use this knob to switch the radio ON and OFF, as well as to adjust the receiver volume to the desired level. To adjust the receiver volume (if no signals are received on the operating channel), open the SQUELCH and then adjust the receiver volume using the background noise as a reference. 10. Microphone Connector Insert the microphone lead to this connector and turn the connector ring in a clockwise to lock it. Rear 11.
User Manual CM10 Installation Before installing the main unit in a vehicle, identify the most convenient location, so that the radio will be easy to reach and comfortable to operate, without disturbing or interfering with driving the vehicle. Use the supplied bracket and hardware to install the radio. The bracket screws must be well tightened to prevent loosening with the vehicle vibrations.
User Manual CM10 Operational Test Once radio has been connected to the vehicles electricity supply and to the antenna, the correct operation of the system may be checked. Please proceed as follows: 1) Check that the power cable is correctly connected. 2) Check that the RF antenna coaxial cable is correctly connected. 3) Connect the microphone to the connector (located on the front side of the radio). 4) Rotate the SQUELCH knob counter clockwise.
User Manual CM10 Reset To restore the original factory settings (CE frequency brand), follows the below process: 1) Turn the radio OFF. 2) Press and hold the DN key, then turn the radio ON using the OFF/VOLUME knob. 3) The CE frequency band code (code 06) will blink on the display for 3 seconds.
User Manual CM10 Table of Restrictions on the Use of CB Transceivers The following information is only to be used as an indication. They are believed to be correct at the time of printing this manual. It is however the user’s responsibility to check that, in the country where radio is used, providing the regulations for the use of CB transceivers have not been modified.
User Manual CM10 Updated information on National Restrictions BELGIUM, UK, SPAIN, SWITZERLAND In order to use this transceiver in Belgium, UK, Spain and Switzerland, users must have an individual licence. Users coming from abroad may freely use the radio in FM mode, while in order to use it in AM mode they must hold a licence issued in their country of residence. ITALY Foreigners arriving in Italy must get an Italian authorisation.
User Manual CM10 Diagrams Diagrams Page 11 of 14
User Manual Diagrams Page 12 of 14 CM10
User Manual Diagrams Page 13 of 14 CM10
User Manual nt User Statemeent Page 14 of 14 CM10
