Technical Specifications

Phone: [phone] | Fax: [phone] | Web: www.maxlite.com | E-mail: [e-mail]
MAX16074
Revised: 05-30-17
Page: 3 of 4
TRIMAX
TRI-PROOF VAPOR TIGHT SERIES
I – Disable
II – 50Lux
III – 10Lux
IV – 2Lux
I – 0s
II – 10s
III – 1min
IV – 5min
V – 10min
VI – 30min
VII – 1H
VIII –
This is the time period you would like to keep at the low light output
level before it is completely switched o in the long absence of people.
This is the dimmed low light output level you would like to have after
the hold-time in the absence of people.
Stand-by period (corridor function)
3
Stand-by dimming level
4
5%
10%
20%
30%
Disable
50Lux
10Lux
2Lux
0s
10s
1min
5min
10min
30min
1H
+
“Daylight” : The lamp works always,even during daylight.
“Twilight” : The lamp works only in twilight and in darkness.
“Darkness” : The lamp works only in darkness.
I – 5%
II – 10%
III – 20%
IV – 30%
application.
Daylight sensor
5
Operating voltage
Switched power (capacitive load)
Stand-by power
Detection area
Hold-time
Stand-by period
Stand-by dimming level
Daylight threshold
Sensor principle
Microwave frequency
Microwave power
Detection range
Detection angle
Mounting height
Operating temperature
120~277VAC
400W@120VAC; 800W@230VAC; 1000W@277VAC
<1W
10%/50%/75%/100% (100% /50% /10% on RC)
5s/30s/1min/5min/10min/20min/30min (TEST 2s/30s/1min/5min/10min/30min on RC)
0s/10s/1min/5min/10min/30min/1h/+∞ ( 0s /10s / 1min / 10min/ 30min /+∞ on RC)
5%/10%/20%/30% (10%/20%/30% on RC)
2~50Lux/disable (2Lux /10Lux / 50Lux /Lux disable on RC)
High frequency (microwave)
5.8GHz+/-75MHz
0.2mW
Max. (OxH): 8m x 5m
30
o
~150
o
Max. 5m
-20
o
C ~ +60
o
C
Technical Data
Semko, CB, EMC, CE, R&TTE, SAA
∞
+
Note: “0s” means on/o control;
daylight sensor is disabled.
8
I – 100%
II – 75%
III – 50%
IV – 10%
Detection area can be reduced by selecting the combination on the
I – 5s
II – 30s
III – 1min
IV – 5min
V – 10min
VI – 20min
VII – 30min
Hold-time means the time period to keep the lamp on 100%, after all
motion has ceased (detection area vacated).
Hold-time
Detection area
1
2
100%
75%
50%
10%
5s
30s
1min
5min
10min
20min
30min
Below are all available settings for the MS (motion sensor) option. Default
settings are highlighted in green. To change the default settings, purchase of
the remote control (RMHYTHRC-05) is required.
Ceiling mounted height (Ft)
10%
10%
30%
30%
75%
75%
50%
50%
16Ft
13Ft
Ceiling mounted detection pattern (Ft)
HRC-05
Stand-by dimming level
Detection range
ON/
OFF
Auto Mode
Reset
Power
80%
Test
2s
10%
20%
30s 1min
100%
30min10min5min
0s 10s 1min
30%
SC1 SC2
SC3
Scene mode
10min
50% 10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
Daylight Sensor
SC4
Power
100%
+
-
Dim
M/A
Remote control (REMOTE-HYT1)
I – Disable
II – 50Lux
III – 10Lux
IV – 2Lux
I – 0s
II – 10s
III – 1min
IV – 5min
V – 10min
VI – 30min
VII – 1H
VIII –
This is the time period you would like to keep at the low light output
level before it is completely switched o in the long absence of people.
This is the dimmed low light output level you would like to have after
the hold-time in the absence of people.
Stand-by period (corridor function)
3
Stand-by dimming level
4
5%
10%
20%
30%
Disable
50Lux
10Lux
2Lux
0s
10s
1min
5min
10min
30min
1H
+
“Daylight” : The lamp works always,even during daylight.
“Twilight” : The lamp works only in twilight and in darkness.
“Darkness” : The lamp works only in darkness.
I – 5%
II – 10%
III – 20%
IV – 30%
application.
Daylight sensor
5
Operating voltage
Switched power (capacitive load)
Stand-by power
Detection area
Hold-time
Stand-by period
Stand-by dimming level
Daylight threshold
Sensor principle
Microwave frequency
Microwave power
Detection range
Detection angle
Mounting height
Operating temperature
120~277VAC
400W@120VAC; 800W@230VAC; 1000W@277VAC
<1W
10%/50%/75%/100% (100% /50% /10% on RC)
5s/30s/1min/5min/10min/20min/30min (TEST 2s/30s/1min/5min/10min/30min on RC)
0s/10s/1min/5min/10min/30min/1h/+∞ ( 0s /10s / 1min / 10min/ 30min /+∞ on RC)
5%/10%/20%/30% (10%/20%/30% on RC)
2~50Lux/disable (2Lux /10Lux / 50Lux /Lux disable on RC)
High frequency (microwave)
5.8GHz+/-75MHz
0.2mW
Max. (OxH): 8m x 5m
30
o
~150
o
Max. 5m
-20
o
C ~ +60
o
C
Technical Data
Semko, CB, EMC, CE, R&TTE, SAA
∞
+
Note: “0s” means on/o control;
daylight sensor is disabled.
8
I – 100%
II – 75%
III – 50%
IV – 10%
Detection area can be reduced by selecting the combination on the
I – 5s
II – 30s
III – 1min
IV – 5min
V – 10min
VI – 20min
VII – 30min
Hold-time means the time period to keep the lamp on 100%, after all
motion has ceased (detection area vacated).
Hold-time
Detection area
1
2
100%
75%
50%
10%
5s
30s
1min
5min
10min
20min
30min
Below are all available settings for the MS (motion sensor) option. Default
settings are highlighted in green. To change the default settings, purchase of
the remote control (RMHYTHRC-05) is required.