Installation Sheet

ManualsBrandsMaxLite ManualsRecessed LightsMaxLite Retrofit Downlight 6" LED Reflector Trim Integrated Recessed Fixture - 18 Watts

Operating Instructions ECO Series

MaxLite ECO Series 6” & 8” Commercial Downlight Retrofit

• To reduce the risk of death, personal injury or property damage from fire, electric

shock, falling parts, cuts/abrasions, and other hazards read all warnings and

instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this

equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires

should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation

or maintenance of the luminaires, consult a qualified licensed

electrician and check your local electrical code.

• DO NOT INSTALL DAMAGED PRODUCT!

• This fixture is intended to be connected to a properly installed and

grounded UL listed junction box.

WARNING:

• Risk of Electrical Shock! Disconnect power at fuse or circuit breaker before installing or servicing.

• Risk of Fire! Do not install insulation within 76 mm (3 in) of any part of the luminaire or in a way that may entrap heat.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

• Installation and servicing to be performed only by qualified personnel, If not qualified, consult an electrician.

• Do not energize the LED Engine until the protective covering has been removed and the lower trim properly

installed. Do not touch the yellow surface of the LED as it may damage the light engine.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION: RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing

or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

• This unit is for recessed mounting only. Do not use in hazardous locations nor near gas or electric heaters.

• Do not use this equipment for other than the intended use.

• Install only in accordance with National Electrical Code and local regulatory agencies’ requirements.

• Install this kit only in luminaires that have the construction features and dimensions shown in

the photographs and/or drawings.

• Installation of this retrofit assembly requires a person familiar with the construction and operation of the

luminaire’s electrical system and the hazard involved. If not qualified, do not attempt installation. Contact

a qualified electrician.

• Do not alter, relocate, or remove wiring, lampholders, power supply, or any other electrical

component unless specifically mentioned in these instructions or shown in the included

photographs and/or drawings.

• Only those open holes indicated in the photographs and/or drawings may be made or altered as a result

of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

• Keep combustable and other materials that can burn away from luminaire and lamp/lens

• MIN 90°C SUPPLY CONDUCTORS.

• LES FILS D’ALIMENTATION 90°C MIN

• SUITABLE FOR DAMP LOCATIONS

• CONVIENT AUX EMPLACEMENTS HUMIDES

• MIN. LAMP COMPARTMENT DIMENSIONS 152 mm (D) X 144mm (H) for 6inch & 203 mm (D) X 160mm (H) for 8inch

This luminaire has been modified to operate LED lamps. Do not attempt to install or operate fluorescent

lamps in this luminaire.

Ce luminaire a été modifié pour faire fonctionner les lampes LED. N'essayez pas d'installer ou d'utiliser des

lampes fluorescentes dans ce luminaire.

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

General Safety Information

Picture is for illustration purposes

only. Your model may vary.

Page: 1

REV: 5/17/17

Summary of content (4 pages)

PAGE 1
Operating Instructions MaxLite® ECO Series 6” & 8” Commercial Downlight Retrofit ECO Series General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 2
Operating Instructions MaxLite® ECO Series 6” & 8” Commercial Downlight Retrofit ECO Series LED Lamp Replacement Marking - Identifying the replacement LED lamp type/model to be used along with manufacturer and ordering information.
PAGE 3
Operating Instructions MaxLite® ECO Series 6” & 8” Commercial Downlight Retrofit ECO Series Wiring Diagram Installation & Operation (Continued) 4.) Set the LED driver box beside the frame. Tuck one connection end into existing J-box to connect electrical power. (See wiring diagram.) 5.) Connect the downlight with driver using the quick connector. 6.) A. If the fixture is not secured properly by existing hardware, secure the 3 mounting clips supplied to the aperature ring. B.
PAGE 4
Operating Instructions MaxLite® ECO Series 6” & 8” Commercial Downlight Retrofit ECO Series Warranty Information MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.