Installation Instructions

ManualsBrandsMaxLite ManualsShop All MaxLiteMaxLite Litebar Left Joiner

Operating Instructions LiteBar Series

MaxLite LED Self-Driven LiteBars

• To reduce the risk of death, personal injury or property damage from fire,

electric shock, falling parts, cuts/abrasions, and other hazards read all

warnings and instructions included with and on the fixture box and all

fixture labels.

• Before installing, servicing, or performing routine maintenance upon

this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires

should be performed by a qualified licensed electrician.

• DO NOT INSTALL DAMAGED PRODUCT!

• This fixture is intended to be connected to a properly installed and

grounded UL listed junction box.

WARNING:

RISK OF ELECTRICALSHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture

to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label

information.

• Make all electrical and grounded connections in accordance with the National Electrical

Code and any applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION:

RISK OF INJURY

• Unit will fall if not installed properly. Follow installation instructions.

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,

servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

CAUTION:

RISK OF FIRE

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

0.77”

(

General Safety Information

Page: 1

REV: 1/23/18

Available lengths: 6”, 12”, 24”, 36” or 48”

This unit contains both AC in and AC out terminals.

Width: 19mm

Height: 20mm

Picture is for illustration purposes

only. Your model may vary.

AC out AC in

Summary of content (16 pages)

PAGE 1
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 2
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Accessories Length: 4”, 12”, 40” Connector Box Distribution Box Straight Joiner Left Joiner Right Joiner Wire Joiner Mounting Clip Wire Joiner with Plug length: 40” Magnet Bracket End Cap Rotation Bracket © Copyright 2018. MaxLite, Inc. All Rights Reserved. 12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.
PAGE 3
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Connector Box Assembly Instructions 1.) Fix the metal sheath to the connector box. 2.) Fix the connector box to a wall by 4 screws. 3.) Connect the AC wires correspondingly with wire caps. 4.) Fix the connector box cover to the connector box with 4 screws. Function Description AC out junction Ground AC ---L AC ---N NOTE: ”AC out” junction should be connected to the distribution box by a wire joiner. Wire Joiner © Copyright 2018.
PAGE 4
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Distribution Box Assembly Instructions 1.) Fix the distribution box to a wall with 2 screws. Screws Distribution box Wall Function Description AC out junction connects to a LiteBar by a wire joiner. AC out junction connects to a LiteBar by a wire joiner. AC in junction connects to the connector box by a wire joiner. © Copyright 2018. MaxLite, Inc. All Rights Reserved.
PAGE 5
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars General Connection Description 1.) The distribution box supplies 2 channels of AC output and controls the on/off function of the LiteBar. 2.) The wire joiners connect the connection box, distribution box and the LiteBar as shown in the figure. AC in Connector box LiteBar Wire joiner End cap Distribution box © Copyright 2018. MaxLite, Inc. All Rights Reserved.
PAGE 6
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Extension Connection Description 1.) The distribution box supplies 2 channels of AC output and control the on/off function of the LiteBar. 2.) Any connection of LiteBars can be formed with the wire joiner, left joiner, right joiner and straight joiner. 3.) The maximum connection length that can be formed is 40 ft.
PAGE 7
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Mounting Bracket Options 1.) Fix the rotation bracket with 2 screws, then insert the LiteBar into the clip. The bracket can rotate between -35 to +35 degrees. Rotation bracket 2.) Attach the bracket to a magnetic surface so that no screws are necessary. Insert the LiteBar into the clip. Magnet bracket 3.) Insert the LiteBar into the clip. Fix the bracket to the mounting surface with 2 screws. Mounting clip © Copyright 2018.
PAGE 8
Operating Instructions LiteBar Series MaxLite® LED Self-Driven LiteBars Warranty Information MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.
PAGE 9
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Informations générales sur la sécurité • Pour réduire les risques de décès et de dommages corporels ou matériels causés par des incendies, décharges électriques, chutes de pièces, coupures/ écorchures et autres dangers, lisez tous les avertissements et toutes les instructions accompagnant le dispositif d'éclairage ainsi que celles indiquées sur ses étiquettes.
PAGE 10
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Accessoires Longueur 10,2 cm, 30,5 cm, 101,6 cm Boîtier de raccordement Boîtier de distribution Raccord droit Raccord câblé Clip de montage Raccord de gauche Raccord câblé avec fiche Longueur : 101,6 cm Support à aimant Raccord de droite Capuchon d'extrémité Support rotatif © Droit d'auteur 2018. MaxLite, Inc. Tous droits réservés.
PAGE 11
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Instructions sur le montage du boîtier de raccordement 1.) Fixez la plaque de métal sur le boîtier de raccordement 2.) Fixez le boîtier de raccordement sur le mur avec 4 vis. 3.) Branchez les câbles CA respectivement avec leurs capuchons. 4.) Fixez le couvercle du boîtier de raccordement sur celui-ci avec de 4 vis.
PAGE 12
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Instructions sur le montage du boîtier de distribution 1.) Fixez le boîtier de distribution sur un mur avec 2 vis. Vis Boîtier de distribution Mur Description de la fonction Le raccordement de sortie CA est raccordé à la LiteBar (barre lumineuse) à l'aide d'un raccord câblé. Le raccordement de sortie CA est raccordé à la LiteBar (barre lumineuse) à l'aide d'un raccord câblé.
PAGE 13
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Description générale des raccordements 1.) Le boîtier de distribution alimente deux canaux de sortie AC et contrôle la fonction marche/ arrêt de la LiteBar (barre lumineuse). 2.) Le raccord câblé raccorde le boîtier de raccordement, le boîtier de distribution et la LiteBar (barre lumineuse), comme illustré sur le croquis.
PAGE 14
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Description des raccordements des extensions 1.) Le boîtier de distribution alimente deux canaux de sortie AC et contrôle la fonction marche/ arrêt de la barre lumineuse. 2.) Tous les raccordements des LiteBars (barres lumineuses) peuvent être effectués avec le raccord câblé, le raccord de gauche, le raccord de droite et le raccord droit. 3.
PAGE 15
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Options du support de montage 1.) Fixez le raccord rotatif avec 2 vis, puis insérez la barre lumineuse dans le clip. Le support peut effectuer des rotations entre -35 et +35 degrés. Support de rotation 2.) Fixez le support sur une surface magnétique afin qu'aucune vis ne soit nécessaire. Insérez la barre lumineuse dans le clip. Support à aimant 3.) Insérez la barre lumineuse dans le clip.
PAGE 16
Instructions d'utilisation Gamme LiteBar (barres lumineuses) LiteBars (barres lumineuses) autonomes DEL MaxLite® Informations relatives à la garantie MaxLite Inc.