User Manual

12
model no. 054-1349-8 | contact us 1-888-670-6682
13
TM
FITTING AND REMOVING THE BATTERY PACK TO THE
DRILL DRIVER
•Toinstallthebatterypacktothetool,aligntheraised
portion of the battery pack with the grooves on the
bottom of the tool handle, and slide it firmly into the
handle until you hear the lock snap into place. (Fig. A)
•Toremovethebatterypackfromthetool,pressthe
battery pack release button and slide the battery pack
completely out of the tool handle.
CHARGING PROCEDURE
•Connecttheplugcabletothecharger,andthenplugintoan
appropriate outlet before inserting battery pack (Fig. B).
All three charging lights will be on for two seconds and
then off.
•Insertthebatterypackintothecharger,makingsurethe
pack is fully seated in the charger (Fig. C). During the
charging process, the charging lights will indicate the
chargingstatusasfollows:
-Lessthan30%charged:allthreecharginglightswill
blink in sequence.
-Lessthan60%charged:onelightwillstayon,while
OPERATING INSTRUCTIONS
the other two lights will blink in sequence.
-Over60%charged:twolightswillstayon,whilethe
remaining light will blink continuously.
-Fullycharged:allthreelightswillremainon
continuously.
•Thechargingprocesswillbelastapproximately35minutes
and permanent lighting of all three charging lights will
indicate charging is complete.
CHARGER DIAGNOSTICS
The charger is designed to detect certain problems that can arise with battery packs.
•Whenthechargerdetectsabatterypackthatisoverheated,allthreecharging
lights will blink at the same time. Please remove the battery and allow it to cool
down for 15–30 minutes and re-insert.
•Whenthechargerdetectsamalfunctioninthebattery,twocharginglightswillblink
at the same time. Please remove the battery and allow it to cool down for 15–30
minutes. Then re-insert the battery pack into the charger. If two charging lights still
flash, the battery may require service.
•Whenthechargerdetectsamalfunctionofthechargeritself,threecharginglights
will blink at the same time. Please remove the battery pack and unplug the charger
for at least 2 minutes. After 2 minutes, plug charger back in and re-insert the pack
into the charger. If all three charging lights still blink at the same time, the charger
may require service.
ON/OFF TRIGGER SWITCH
To turn the tool on, squeeze the trigger switch. To turn the tool off, release the trigger
switch.
VARIABLE SPEED
The variable speed trigger switch delivers higher speed with increased trigger pressure
and lower speed with decreased trigger pressure. For maximum tool life, use variable
speed only for starting holes or fasteners.
OPERATING INSTRUCTIONS
WARNING!
•Donotallowfamiliaritywithtoolstomakeyoucareless.
Remember that a careless fraction of a second is enough to
cause serve injury.
•Beforeattemptingtousethiscordlesstool,becomefamiliar
with all of its operating features and safety requirements.
•Toreducetheriskofseriouspersonalinjury,turntooloff
and disconnect battery pack before making any adjustments
or removing/installing attachments or accessories.
CAUTION!
•Beforeattemptingtochargethebattery,checkthecharger
and the battery to ensure the charging equipment matches
the battery supplied. The components are all labeled with
component numbers.
•Therechargeablebatteryisnotfullychargedonleavingthe
factory. Charge the rechargeable battery before first use.
•Rechargedischargedbatteriesassoonaspossibleafteruse
or battery life may be greatly diminished. For longest battery
life, do not discharge batteries fully.
• The working temperature of the charger is 0-45°C (32-113°F).
NOTE:Charging times may be longer depending on the
surrounding temperature and battery conditions.
CAUTION!
The variable speed control function is not intended to be used
for long periods of time during the operation of the task being
performed. Use the variable speed to start drilling and screwing
tasks, and then fully press the once the trigger switch task has
started.