TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY INSTRUCTIONS IMPORTANT INFORMATION PARTS LIST KNOW YOUR TOOL OPERATING INSTRUCTIONS MAINTENANCE WARRANTY NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-888-670-6682. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. Read all instructions and follow them with use of this product.
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS MOTOR DRIVE VARIABLE SPEEDS MAX. TORQUE ON-BOARD WORK LIGHT BATTERY REPLACEMENT BATTERIES CHARGER COMPATIBLE MAXIMUM CHARGER OPTIMUM CHARGING TEMPERATURE DIMENSIONS WEIGHT 18V DC 1/2” square 0–2700 RPM/0–3300 BPM 145 ft-lb LED 20V max* (2.0 Ah) lithium-ion 054-3203-2 (2.0 Ah); 054-3206-6(4.0 Ah) 35-minute, diagnostic 054-3204-0 50 to 86°F (10–30°C) 6 5/16 x 7 13/32 x 2 11/16” (160 x 188 x 68 mm) 2 lb 5 oz (1.
• SAFETY INSTRUCTIONS • Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection will reduce personal injuries. Avoid accidental starting. Ensure the switch is in the “off” position before connecting to a power source and/or battery pack, or picking up or carrying the tool. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
SAFETY INSTRUCTIONS FOR BATTERY PACK AND CHARGER ADDITIONAL INFORMATION ON BATTERY AND CHARGER • • The battery pack is not fully charged out of the carton. First read the safety instructions and then follow the charging notes and procedures. If the battery pack casing is cracked or damaged, do not insert into charger. There is a danger of electric shock or electrocution. SAFETY INSTRUCTIONS TM • Don’t allow any liquid to get inside charger. Electric shock may result.
TM No. Description No. Description 1 1/2” square anvil 6 Battery release button 2 LED worklight 7 Rechargeable battery pack 3 Forward & reverse lever 8 Charger 4 Trigger switch 9 Charging indicator 5 Remaining power indicator 10 Detachable cable & plug 1 3 4 2 5 PARTS LIST 6 7 9 10 1 8 11 2 12 17 2 4 3 13 14 15 16 9 8 5 10 7 18 6 WARNING! • Remove the product and any accessories from the package.
OPERATING INSTRUCTIONS FITTING AND REMOVING THE BATTERY PACK TO THE IMPACT WRENCH • To install the battery pack to the tool, align the raised portion of the battery pack with the grooves on the bottom of the tool, and slide it firmly into the handle until you hear the lock snap into place. (Fig. A) • To remove the battery pack from the tool, press the battery pack release button and slide the battery pack completely out of tool handle.
TM VARIABLE SPEED LED WORKLIGHT The variable speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. When the unit is switched on, the LED worklight also comes on to ensure better vision and to make working in dark areas safer. LED work light remains on for 15 seconds after the trigger switch is released. FORWARD AND REVERSE The direction of bit rotation is reversible and is controlled by a selector located above the trigger switch.
OPERATING INSTRUCTIONS LOW-VOLTAGE CUT-OUT The battery pack used on this tool is fitted with a low-voltage cut-out feature within the circuitry. The low-voltage cut-out feature operates when the voltage drops below a pre-set value. This feature automatically stops the tool from operating. When this condition occurs you will need to either insert another battery pack into the tool or recharge the existing battery pack. TM • Bolt.
GENERAL MAINTENANCE BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries.
5-YEAR LIMITED WARRANTY This MAXIMUM product is guaranteed for a period of 5 years from the date of original retail purchase against defects in workmanship and materials only and is subject to the following components: a) Component A: The carrying case is guaranteed for a period of 1-year from the date of original retail purchase against defects in workmanship and materials. WARRANTY b) Component B: Accessories, including drill bits and saw blades, do not carry a warranty.
22 model no. 054-3245-2 | contact us 1-888-670-6682 whatsoever relating to interruption, delays, errors or omissions; in each case under any theory of law or equity, arising out of or in any way related to this warranty, even if advised of the possibility thereof.
