R TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY GUIDELINES KEY PARTS DIAGRAM TECHNICAL INFORMATION TYPES OF STAPLES OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING EXPLODED VIEW PARTS LIST WARRANTY NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-888-670-6682.
4 R model no. 058-9841-8 | contact us 1-888-670-6682 TECHNICAL SPECIFICATIONS MAGAZINE CAPACITY 100 staples STAPLES 18-gauge 1/4’’ narrow crown (5/8 – 1 1/2") OPERATING PRESSURE 70–120 PSI (4.8–8.3 bar) AIR CONSUMPTION 0.035 CF/cycle @ 90 PSI AIR INLET 1/4" – 18 NPT WEIGHT 2 lb 10 oz (1.2 kg) CF: Cubic Feet (the volumetric flow rate of air corrected to standardized conditions of temperature and pressure). NPT: National Pipe Thread.
6 R model no. 058-9841-8 | contact us 1-888-670-6682 SAFETY GUIDELINES Risk of burns. The pump and the manifold generate high temperatures. In order to avoid burns or other injuries, do not touch the pump, the manifold or the transfer tube while the compressor is running. Allow the parts to cool down before handling or servicing. Keep children and pets away from the compressor at all times. • Do not use oxygen or any other combustible or bottled gas to power air-powered tools.
TM 8 R model no. 058-9841-8 | contact us 1-888-670-6682 Disconnect the tool from the air supply and turn off the compressor before performing any maintenance, loading or changing staples, when the tool is not in use. when it is being handed to another person, and when it is left unattended. Failure to comply may result in injury or damage to equipment. Carry the tool by the handle only. Do not carry the tool with a finger on the trigger.
10 R model no. 058-9841-8 | contact us 1-888-670-6682 No. Description No. Compatible compressors Description GUIDELINES FOR PROPER USE AND OPERATION 1 Air inlet plug 4 Safety tip 2 Magazine latch 5 Depth adjustment dial 3 Magazine 6 Trigger 7 Rear exhaust Be sure to use a proper air compressor with MAXIMUM® air-powered tools. The compressor that is being used must be able to supply appropriate amount of pressure (PSI) to the tool.
12 R model no. 058-9841-8 | contact us 1-888-670-6682 Air system • Always use clean, dry, regulated, compressed air at 4.8 to 8.3 bar (70 to 120 PSI). • Do not exceed the maximum or minimum pressures. Operating the tool at inappropriate pressure (too low or too high) will cause excessive noise or rapid wear. 2 3 1 6 7 3 5 4 8 No. Description No. Description 1 MAXIMUM Air-powered Stapler 5 Regulator 0–123 PSI (0–8.
14 R model no. 058-9841-8 | contact us 1-888-670-6682 This MAXIMUM® Air-powered Stapler drives 18-gauge 1/4’’ narrow crown 5/8 1 1/2" (15 38 mm) long staples. ACCEPTABLE STAPLES STAPLES Length: 5/8 to 1 1/2" (15 to 38 mm) Loading Staples Fig. A 1. Disconnect the tool (1) from the air supply (2) (Fig. A). Fig. B 1 1 2 2. Hold the Air-powered Stapler firmly with one hand. Use the other hand to press the latch (1) on the magazine (2) and slide it back (Fig. B).
16 R model no. 058-9841-8 | contact us 1-888-670-6682 Fig. E 1 5. Test the driving depth of the tool against a scrap piece of wood by pressing the trigger (1) before working on the workpiece. If the staples are being driven too deep or not deep enough, adjust the depth adjustment dial to achieve desired penetration (Fig. E). 6. This tool is featured with anti-dry fire function. When only few staples are remained in magazine, tool will be locked until reloading more staples.
18 R model no. 058-9841-8 | contact us 1-888-670-6682 Cold weather operation When operating any air-powered tool below freezing temperature: • Verify that the compressor tanks have been properly drained prior to use. • Keep the tool as warm as possible using any safe, convenient method. • Maintain the operating level of the air pressure as recommended (see section “Technical Specifications”). • Load the staples into the magazine (if required).
20 R model no. 058-9841-8 | contact us 1-888-670-6682 Troubleshooting The following chart lists common issues and solutions. Please read it carefully and follow all instructions carefully. • Disconnect the tool from the air supply before making any adjustments. • Repairs and replacement must be performed only by a qualified service technician or in an authorized service centre. PROBLEM POSSIBLE CAUSES SOLUTIONS Air leakage in the trigger area. 1. O-rings in the trigger valve are damaged. 1.
22 R EXPLODED VIEW AND PARTS LIST model no. 058-9841-8 | contact us 1-888-670-6682 No. Description No.
24 model no. 058-9841-8 | contact us 1-888-670-6682 This MAXIMUM product is guaranteed for a period of 5 years from the date of original retail purchase against defects in workmanship and materials only and is subject to the following components: Component A: The carrying case is guaranteed for a period of 1-year from the date of original retail purchase against defects in workmanship and materials.
26 R model no. 058-9841-8 | contact us 1-888-670-6682 Additional Limitations This warranty applies only to the original purchaser and may not be transferred. In addition to the 5-Year Limited Warranty, this MAXIMUM product is covered by our: This warranty applies for a period of 5 years from the date of original retail purchase, as indicated on the bill of sale.
