User Manual

12
model no. 054-3213-8 | contact us 1-888-670-6682
13
TM
INTENDED USE
This tool is intended for the fastening and loosening of bolts,
nuts and various threaded fasteners within the respective
range of dimensions. This cordless impact driver has a collet
that accepts only standard 1/4” (6.35 mm) hexagonal shank
accessories with power groove. The electronic variable speed
also provides more control to prevent stripping of the screw
and damage to the work surface.
FITTING AND REMOVING THE BATTERY PACK TO THE
IMPACT DRIVER
•Toinstallthebatterypacktothetool,aligntheraised
portion of the battery pack with the grooves on the
bottom of the tool and slide it firmly into the handle until
you hear the lock snap into place. (Fig. A)
•Toremovethebatterypackfromthetool,pressthe
battery pack release button and slide the battery pack
completely out of tool handle.
CHARGING PROCEDURE
•Connecttheplugcabletothecharger,thenplugintoan
appropriate outlet before inserting battery pack (Fig. B).
All three charging lights will be on for two seconds and
OPERATING INSTRUCTIONS
then off.
•Insertthebatterypackintothecharger,makingsurethe
pack is fully seated in the charger (Fig. C). During the
charging process, the charging lights will indicate the
chargingstatusasfollows:
-Lessthan30%charged:allthreecharginglightswill
blink in sequence.
-Lessthan60%charged:onelightwillstayon,while
the other two lights will blink in sequence.
-Over60%charged:twolightswillstayon,whilethe
remaining light will blink continuously.
-Fullycharged:allthreelightswillremainon
continuously.
•Thechargingprocesswilllastapproximately30minutes
and permanent lighting of all three charging lights will
indicate charging is complete.
CHARGER DIAGNOSTICS
The charger is designed to detect certain problems that can
arise with battery packs.
•Whenthechargerdetectsthebatterypackisoverheated,allthreecharginglights
will blink at the same time. Please remove the battery and allow it to cool down for
15–30 minutes then re-insert.
•Whenthechargerdetectsamalfunctioninthebattery,twocharginglightswillblink
at the same time. Please remove the battery and allow it to cool down for 15–30
minutes. Then re-insert the battery pack into the charger. If two charging lights still
flash, the battery may require service.
•Whenthechargerdetectsamalfunctionofthechargeritself,threecharginglights
will blink at the same time. Please remove the battery pack and unplug the charger
for at least 2 minutes. After 2 minutes, plug charger back in and re-insert the pack
into the charger. If all three charging lights still blink at the same time, the charger
may require service.
OPERATING INSTRUCTIONS
WARNING!
•Donotallowfamiliaritywithtoolstomakeyoucareless.
Remember that a careless fraction of a second is enough to
cause serve injury.
•Beforeattemptingtousethiscordlesstool,becomefamiliar
with all of its operating features and safety requirements.
•Toreducetheriskofseriouspersonalinjury,turntooloff
and disconnect battery pack before making any adjustments
or removing/installing attachments or accessories.
CAUTION!
•Beforeattemptingtochargethebattery,checkthecharger
and the battery to ensure the charging equipment matches
the battery supplied. The components are all labeled with
component numbers.
•Therechargeablebatteryisnotfullychargedonleavingthe
factory. Charge the rechargeable battery before first use.
•Rechargedischargedbatteriesassoonaspossibleafteruse
or battery life may be greatly diminished. For longest battery
life, do not discharge batteries fully.
CAUTION!
The working temperature of the charger is 32–113°F
(0–45°C)
NOTE: Charging times may be longer depending on the
surrounding temperature and battery conditions.