Datasheet
Table Of Contents
- FEATURES
- DETAILED DESCRIPTION
- ORDERING INFORMATION
- Figure 1. Block Diagram
- PIN DESCRIPTION
- 80C32 COMPATIBILITY
- Figure 2. Comparative Timing of the DS80C320/DS80C323 and 80C32
- HIGH-SPEED OPERATION
- INSTRUCTION SET SUMMARY
- Table 1. Instruction Set Summary
- SPEED ADVANTAGE SUMMARY
- MEMORY ACCESS
- Figure 3. Typical Memory Connection
- STRETCH MEMORY CYCLE
- Table 2. Data Memory Cycle Stretch Values
- DUAL DATA POINTER
- 64-Byte Block Move without Dual Data Pointer
- 64-Byte Block Move with Dual Data Pointer
- PERIPHERAL OVERVIEW
- SERIAL PORTS
- TIMER-RATE CONTROL
- POWER-FAIL RESET
- POWER-FAIL INTERRUPT
- WATCHDOG TIMER
- Table 3. Watchdog Timeout Values
- INTERRUPTS
- Table 4. Interrupt Priority
- POWER MANAGEMENT
- IDLE MODE ENHANCEMENTS
- STOP MODE ENHANCEMENTS
- Figure 4. Ring Oscillator Startup
- TIMED ACCESS PROTECTION
- SPECIAL-FUNCTION REGISTERS
- Table 5. Special-Function Register Locations
- ELECTRICAL SPECIFICATIONS
- ABSOLUTE MAXIMUM RATINGS
- DC ELECTRICAL CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
- TYPICAL ICC vs. FREQUENCY
- AC CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C320
- DC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS (continued)
- AC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C323
- EXTERNAL CLOCK CHARACTERISTICS
- SERIAL PORT MODE 0 TIMING CHARACTERISTICS
- EXPLANATION OF AC SYMBOLS
- POWER-CYCLE TIMING CHARACTERISTICS
- NOTES FOR POWER CYCLE TIMING CHARACTERISTICS
- PROGRAM MEMORY READ CYCLE
- DATA MEMORY READ CYCLE
- DATA MEMORY WRITE CYCLE
- DATA MEMORY WRITE WITH STRETCH = 1
- DATA MEMORY WRITE WITH STRETCH = 2
- EXTERNAL CLOCK DRIVE
- SERIAL PORT MODE 0 TIMING
- POWER-CYCLE TIMING
- DATA SHEET REVISION SUMMARY
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
38 of 38
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
DATA SHEET REVISION SUMMARY (continued)
The following represent the key differences between the 05/22/96 and the 10/21/97 version of the DS80C320 data sheet.
Please review this summary carefully.
DS80C320
1. Added note to clarify I
IL
specification.
2.
Added note to clarify AC timing conditions.
3.
Corrected erroneous t
QVXL
label on figure “Serial Port Mode 0 Timing” to read t
QVXH
.
4.
Added note to prevent accidental corruption of Watchdog Timer count while changing counter length.
DS80C323
1. Added note to clarify I
IL
specification.
2.
Remove port 2 from V
OH1
specification, add port 3.
3.
I
OH
for V
OH3
specification changed from -3mA to -2mA.
4.
Added note to clarify AC timing conditions.