Datasheet
Table Of Contents
- FEATURES
- DETAILED DESCRIPTION
- ORDERING INFORMATION
- Figure 1. Block Diagram
- PIN DESCRIPTION
- 80C32 COMPATIBILITY
- Figure 2. Comparative Timing of the DS80C320/DS80C323 and 80C32
- HIGH-SPEED OPERATION
- INSTRUCTION SET SUMMARY
- Table 1. Instruction Set Summary
- SPEED ADVANTAGE SUMMARY
- MEMORY ACCESS
- Figure 3. Typical Memory Connection
- STRETCH MEMORY CYCLE
- Table 2. Data Memory Cycle Stretch Values
- DUAL DATA POINTER
- 64-Byte Block Move without Dual Data Pointer
- 64-Byte Block Move with Dual Data Pointer
- PERIPHERAL OVERVIEW
- SERIAL PORTS
- TIMER-RATE CONTROL
- POWER-FAIL RESET
- POWER-FAIL INTERRUPT
- WATCHDOG TIMER
- Table 3. Watchdog Timeout Values
- INTERRUPTS
- Table 4. Interrupt Priority
- POWER MANAGEMENT
- IDLE MODE ENHANCEMENTS
- STOP MODE ENHANCEMENTS
- Figure 4. Ring Oscillator Startup
- TIMED ACCESS PROTECTION
- SPECIAL-FUNCTION REGISTERS
- Table 5. Special-Function Register Locations
- ELECTRICAL SPECIFICATIONS
- ABSOLUTE MAXIMUM RATINGS
- DC ELECTRICAL CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
- TYPICAL ICC vs. FREQUENCY
- AC CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C320
- DC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS (continued)
- AC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C323
- EXTERNAL CLOCK CHARACTERISTICS
- SERIAL PORT MODE 0 TIMING CHARACTERISTICS
- EXPLANATION OF AC SYMBOLS
- POWER-CYCLE TIMING CHARACTERISTICS
- NOTES FOR POWER CYCLE TIMING CHARACTERISTICS
- PROGRAM MEMORY READ CYCLE
- DATA MEMORY READ CYCLE
- DATA MEMORY WRITE CYCLE
- DATA MEMORY WRITE WITH STRETCH = 1
- DATA MEMORY WRITE WITH STRETCH = 2
- EXTERNAL CLOCK DRIVE
- SERIAL PORT MODE 0 TIMING
- POWER-CYCLE TIMING
- DATA SHEET REVISION SUMMARY
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
3 of 38
Figure 1. Block Diagram
PIN DESCRIPTION
PIN
DIP PLCC
TQFP
NAME FUNCTION
40 44
38 V
CC
+5V (+3V for DS80C323)
20 22, 23
16, 17 GND
Digital Circuit Ground
9 10 4 RST
Reset Input. The RST input pin contains a Schmitt voltage input to
recognize external active-high reset inputs. The pin also employs an
internal pulldown resistor to allow for a combination of wired OR
external reset sources. An RC is not required for power-up, as the device
provides this function internally.
18 20 14 XTAL2
19 21 15 XTAL1
Crystal Oscillator Pins. XTAL1 and XTAL2 provide support for
parallel-resonant, AT-cut crystals. XTAL1 acts also as an input in the
event that an external clock source is used in place of a crystal. XTAL2
serves as the output of the crystal amplifier.
29 32 26
PSEN
Program Store-Enable Output, Active Low. This signal is commonly
connected to external ROM memory as a chip enable.
PSEN provides an
active-low pulse width of 2.25 XTAL1 cycles with a period of four
XTAL1 cycles.
PSEN is driven high when data memory (RAM) is being
accessed through the bus and during a reset condition.
DS80C320/
DS80C323