Datasheet
Table Of Contents
- FEATURES
- DETAILED DESCRIPTION
- ORDERING INFORMATION
- Figure 1. Block Diagram
- PIN DESCRIPTION
- 80C32 COMPATIBILITY
- Figure 2. Comparative Timing of the DS80C320/DS80C323 and 80C32
- HIGH-SPEED OPERATION
- INSTRUCTION SET SUMMARY
- Table 1. Instruction Set Summary
- SPEED ADVANTAGE SUMMARY
- MEMORY ACCESS
- Figure 3. Typical Memory Connection
- STRETCH MEMORY CYCLE
- Table 2. Data Memory Cycle Stretch Values
- DUAL DATA POINTER
- 64-Byte Block Move without Dual Data Pointer
- 64-Byte Block Move with Dual Data Pointer
- PERIPHERAL OVERVIEW
- SERIAL PORTS
- TIMER-RATE CONTROL
- POWER-FAIL RESET
- POWER-FAIL INTERRUPT
- WATCHDOG TIMER
- Table 3. Watchdog Timeout Values
- INTERRUPTS
- Table 4. Interrupt Priority
- POWER MANAGEMENT
- IDLE MODE ENHANCEMENTS
- STOP MODE ENHANCEMENTS
- Figure 4. Ring Oscillator Startup
- TIMED ACCESS PROTECTION
- SPECIAL-FUNCTION REGISTERS
- Table 5. Special-Function Register Locations
- ELECTRICAL SPECIFICATIONS
- ABSOLUTE MAXIMUM RATINGS
- DC ELECTRICAL CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
- TYPICAL ICC vs. FREQUENCY
- AC CHARACTERISTICS—DS80C320
- NOTES FOR DS80C320 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C320
- DC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS
- NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS (continued)
- AC ELECTRICAL CHARACTERISTICS—DS80C323
- NOTES FOR DS80C323 AC ELECTRICAL CHARACTERISTICS
- MOVX CHARACTERISTICS—DS80C323
- EXTERNAL CLOCK CHARACTERISTICS
- SERIAL PORT MODE 0 TIMING CHARACTERISTICS
- EXPLANATION OF AC SYMBOLS
- POWER-CYCLE TIMING CHARACTERISTICS
- NOTES FOR POWER CYCLE TIMING CHARACTERISTICS
- PROGRAM MEMORY READ CYCLE
- DATA MEMORY READ CYCLE
- DATA MEMORY WRITE CYCLE
- DATA MEMORY WRITE WITH STRETCH = 1
- DATA MEMORY WRITE WITH STRETCH = 2
- EXTERNAL CLOCK DRIVE
- SERIAL PORT MODE 0 TIMING
- POWER-CYCLE TIMING
- DATA SHEET REVISION SUMMARY
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
26 of 38
NOTES FOR DS80C323 DC ELECTRICAL CHARACTERISTICS (continued)
All parameters apply to both commercial and industrial temperature operation unless otherwise noted. Specifications to -40°C
are guaranteed by design and are not production tested. Device operating range is 2.7V to 5.5V. DC electrical specifications are
for operation 2.7V to 3.3V.
6. RST = V
CC
. This condition mimics operation of pins in I/O mode.
7. During a 0-to-1 transition, a one-shot drives the ports hard for two clock cycles. This measurement reflects port
in transition mode.
8. Ports 1, 2, and 3 source transition current when being pulled down externally. It reaches its maximum at
approximately 2V.
9. V
IN
between ground and V
CC
- 0.3V. Not a high-impedance input. This port is a weak address latch because
Port 0 is dedicated as an address bus on the DS80C323. Peak current occurs near the input transition point of
the latch, approximately 2V.
10. Over the industrial temperature range, this specification has a maximum value of 200A.
11. This is the current from an external circuit to hold a logic low level on an I/O pin while the corresponding port
latch bit is set to 1. This is only the current required to hold the low level; transitions from 1 to 0 on an I/O pin
will also have to overcome the transition current.
12. Device operating range is 2.7V to 5.5V, however device is tested to 2.5V to ensure proper operation at
minimum V
RST
.