Datasheet

MAX9021/MAX9022/MAX9024
Micropower, Ultra-Small, Single/Dual/Quad,
Single-Supply Comparators
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage (V
DD
to V
SS
) ....................................-0.3V to +6V
Voltage Inputs (IN+, IN- to V
SS
). ................-0.3V to (V
DD
+ 0.3V)
Differential Input Voltage (IN+ to IN-)....................................6.6V
Current into Input Pins ......................................................±20mA
Output Short-Circuit Duration ..................2s to Either V
DD
or V
SS
Current into Any Pin ............................................................20mA
Continuous Power Dissipation (T
A
= +70°C)
5-Pin SC70 (derate 3.1mW/°C above +70°C)...............247mW
5-Pin SOT23 (derate 7.1mW/°C above +70°C).............571mW
8-Pin SOT23 (derate 9.1mW/°C above +70°C).............727mW
8-Pin µMAX (derate 4.5mW/°C above +70°C) ..............362mW
8-Pin SO (derate 5.88mW/°C above +70°C).................471mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) ..........727mW
14-Pin SO (derate 8.3mW/°C above +70.......................667mW
Operating Temperature Range
Automotive Application...................................-40°C to +125°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Voltage Range V
DD
Guaranteed by PSRR test
2.5
5.5 V
S up p l y C ur r ent P er C om p ar ator I
DD
2.8 5 µA
Input Offset Voltage V
OS
(Note 2) ±1 ±8mV
Input Offset Voltage
Temperature Coefficient
TCV
OS
±1
µV/°C
Hysteresis (Note 3) 4 mV
Input Bias Current I
BIAS
380nA
Input Offset Current I
OS
±2 ±60 nA
Common-Mode Voltage Range V
CM
Guaranteed by CMRR test
V
SS
V
DD
- 1.1
V
C om m on- M od e Rej ecti on Rati o
CMRR
V
S S
≤ V
C M
≤ ( V
D D
- 1.1V ) , V
D D
= 5.5V 70 100 d B
Power-Supply Rejection Ratio
PSRR
V
DD
= 2.5V to 5.5V 60 80 dB
I
SOURCE
= 10µA 2
V
OH
= V
DD
- V
OUT,
(V
IN+
- V
IN-
) ≥ 20mV
I
SOURCE
= 4mA
160
400
I
SINK
= 10µA 2
Output-Voltage Swing
V
OL
, V
OH
V
OL
= V
OUT
- V
SS,
(V
IN-
- V
IN+
) ≥ 20mV
I
SINK
= 4mA
180
400
mV
Output Short-Circuit Current I
SC
50 m A
V
OD
= 10mV 8
Propagation Delay
t
p
d+
, t
p
d
-
R
L
= 10kΩ,
C
L
= 15pF (Note 4)
V
OD
= 100mV 3
µs
Rise and Fall Time t
R
, t
F
R
L
= 10kΩ, C
L
= 15pF (Note 5) 20 ns
Power-On Time R
L
= 10kΩ, C
L
= 15pF
150
ns
Maximum Capacitive Load C
L
No sustained oscillations
150
pF
Note 1: All devices are production tested at 25°C. All temperature limits are guaranteed by design.
Note 2: Comparator Input Offset is defined as the center of the hysteresis zone.
Note 3: Hysteresis is defined as the difference of the trip points required to change comparator output states.
Note 4: V
OD
is the overdrive voltage beyond the offset and hysteresis-determined trip points.
Note 5: Rise and fall times are measured between 10% and 90% at OUT.
ELECTRICAL CHARACTERISTICS
(V
DD
= 5V, V
SS
= 0, V
CM
= 0, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)