Datasheet

MAX4814E
DVI/HDMI 2:4 Low-Frequency Fanout Switch
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
DD
= +5V ±10%, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C, V
DD
= +5V. Note 2.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages referenced to GND. Note 1.)
V
DD
, A_, B_, SW_, EFN..........................................-0.3V to +6.0V
All Other Pins (except GND).........................-0.3V to V
DD
+ 0.3V
Continuous Current, A_, B_ ..............................................±60mA
Continuous Current, V
DD
or GND...................................±100mA
Continuous Power Dissipation (T
A
= +70°C)
64-Pin TQFP (derate 31.3mW/°C above +70°C)........2508mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering) .........................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT
Power-Supply Voltage V
DD
4.5 5 5.5 V
Power-Supply Current I
DD
E FN = unconnected ; al l i np uts = 0;
al l outp uts hi g h or l ow , no l oad s
10 µA
EFN Leakage Current I
L
V
EFN
= V
DD
- 0.2V -2 +2 µA
LOGIC INPUTS (DA_, DB_, MODE, AD_)
Input Low Voltage DA_, DB_ V
IL
MODE = 0V 0.8 V
Input High Voltage DA_, DB_ V
IH
MODE = 0V 2 V
Input-Voltage Hysteresis DA_, DB_ V
HYST
MODE = 0V 150 mV
Input Low Voltage AD_ V
IL
MODE = V
DD
0.8 V
Input High Voltage AD_ V
IH
MODE = V
DD
2V
Input-Voltage Hysteresis AD_ V
HYST
MODE = V
DD
150 mV
Input Low Voltage MODE V
IL
0.8 V
Input High Voltage MODE V
IH
2V
Input-Voltage Hysteresis MODE V
HYST
150 mV
Input Leakage Current DA_, DB_ I
L
MODE = 0V ±1 µA
Input Leakage Current AD_ I
L
MODE = V
DD
±1 µA
Input Leakage Current MODE I
L
±1 µA
LOGIC OUTPUTS DO_
Output-Voltage Low V
OL
MODE = V
DD
, I
SINK
= 30µA 0.5 V
Output-Voltage High V
OH
MODE = V
DD
, I
SOURCE
= 26µA 2 V
Output Leakage Current I
L
M OD E = V
D D
, outp ut at hi g h i m p ed ance,
V
I N
= 1.5V
±1 µA
Output Rise Time t
R
V
OUT
from 0.8V to 2.2V, C
LOAD
= 10pF 600 ns
I
SOURCE
-1
Output Short-Circuit Current I
SC
I
SINK
+3
mA
Note 1: EFN must be either connected to V
DD
or left unconnected. EFN must not be connected to ground.