Datasheet
MAX4558/MAX4559/MAX4560
±15kV ESD-Protected, Low-Voltage, CMOS
Analog Multiplexers/Switches
6 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V
CC
= +2.7V to +3.6V, V
_H
= +2.0V, V
_L
= +0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
Note 2: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 3: ∆R
ON
= R
ON(MAX)
- R
ON(MIN)
.
Note 4: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal ranges; i.e., V
ON
= 3V to 0 and 0 to -3V.
Note 5: Leakage parameters are 100% tested at the maximum-rated hot operating temperature and are guaranteed by correlation
at T
A
= +25°C.
Note 6: Guaranteed by design, not production tested.
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 1kΩ;
C
L
= 35pF; Figure 1
V
CC
= 2.7V; I
X
, I
Y
, I
Z
= 0.1mA;
V
X
, V
Y
, V
Z
= 1.5V
Ω
0.5
R
ON
On-Resistance
V
A_
, V
B_
,
V
C_
, V
EN
220 400
V
A
, V
B
, V
C
, V
EN
= V
CC
or 0 µA
400
V
A_
, V
B_
,
V
C_
, V
EN
Input Current Logic
High or Low
Input Logic Low
t
ON
-1 1
Turn-On Time ns
C, E
C, E
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 1kΩ;
C
L
= 35pF; Figure 1
V
300
t
OFF
Turn-Off Time ns
C, E
90 250
180 350
V
X
, V
Y
, V
Z
= 1.5V; R
S
= 0; C
L
= 1nF;
Figure 3
pCQCharge Injection
+25°C
0.5+25°C
+25°C
CONDITIONS UNITS
MIN TYP MAX
(Note 2)
SYMBOLPARAMETER T
A
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 1kΩ;
C
L
= 35pF; Figure 1
400
t
TRANS
Address Transition Time ns
C, E
V
X_
, V
Y_
, V
Z_
= 1.5V; R
L
= 1kΩ;
C
L
= 35pF; Figure 2
1.5t
OPEN
Break-Before-Make Delay ns
180 350
C, E
+25°C
C, E
+25°C
V
V
A_
, V
B_
,
V
C_
, V
EN
Input Logic High 1.5C, E
C, E 450
V
CC
= 3.6V; V
A_
, V
B_
, V
C_
, V
EN
= 0 or V
CC
µAI
CC
V
CC
Supply Current
1 0.5 1+25°C
ANALOG SWITCH
DIGITAL I/O
SWITCH DYNAMIC CHARACTERISTICS (Note 6)
POWER SUPPLY
C, E -10 10