Datasheet

MAX4536/MAX4537/MAX4538
Quad, Low-Voltage,
SPST Analog Switches with Enable
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—±5V Dual Supplies
(V+ = 4.5V to 5.5V, V- = -4.5V to -5.5V, V
INH
= 2.4V, V
INL
= 0.8V, V
EN
= 0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical
values are at T
A
= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltages Referenced to GND
V+........................................................................-0.3V to +13.0V
V-.........................................................................-13.0V to +0.3V
V+ to V-................................................................-0.3V to +13.0V
All Other Pins (Note 1) ..........................(V- -0.3V) to (V+ + 0.3V)
Continuous Current into Any Terminal..............................±10mA
Peak Current into Any Terminal
(pulsed at 1ms,10% duty cycle).....................................±20mA
ESD per Method 3015.7 ..................................................>2000V
Continuous Power Dissipation (T
A
= +70°C) (Note 2)
Plastic DIP (derate 10.53mW/°C above +70°C) ............842mW
Narrow SO (derate 8.70mW/°C above +70°C) ..............696mW
QSOP (derate 8.00mW/°C above +70°C)......................800mW
Operating Temperature Ranges
MAX453_C_ E.......................................................0°C to +70°C
MAX453_E_ E ....................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
(Note 4)
V
IN_
= 0.8V or 2.4V
V+ = 5.5V, V- = -5.5V,
V
COM_
= ±4.5V, V
N_ _
= 4.5V
V+ = 5.5V, V- = -5.5V,
V
COM_
= ±4.5V, V
N_ _
= ±4.5V
V+ = 5.0V, V- = -5.0V,
V
COM_
= -3.0V, 0, +3.0V, I
COM_
= 1mA
V+ = 4.5V, V- = -4.5V,
V
COM_
= 3.5V, I
COM_
= 1mA
V+ = 4.5V, V- = -4.5V,
V
COM_
= 3.5V, I
COM_
= 1mA
V+ = 5.5V, V- = -5.5V,
V
COM_
= ±4.5V, V
N_ _
= 4.5V
CONDITIONS
µA-1 0.03 1I
INH_
, I
INL_
EN, IN_ Input Current Logic
High or Low
V0.8 1.4V
INL
EN, IN_ Input Logic Threshold Low
V1.4 2.4V
INH
EN, IN_ Input Logic Threshold High
nA
-20 20
I
COM_(ON)
COM_ On-Leakage Current
(Note 7)
-2 0.01 2
nA
-10 10
I
COM_(OFF)
COM_ Off-Leakage Current
(Note 7)
55 100
VV- V+
V
COM_
,
V
NO_
, V
NC
Analog Signal Range
-1 0.01 1
nA
-10 10
I
NO_(OFF),
I
NC_(OFF)
NO_, NC_ Off-Leakage Current
(Note 7)
-1 0.01 1
Ω
15
R
FLAT(ON)
COM_ NO_, COM_ NC_
On-Resistance Flatness (Note 6)
Ω
125
R
ON
COM_ NO_, COM_ NC_
On-Resistance
14
Ω
6
∆R
ON
COM_ NO_, COM_ NC_
On-Resistance Match Between
Channels (Note 5)
410
UNITS
MIN TYP MAX
(Note 3)
SYMBOLPARAMETER
Note 1: Signals on NC_, NO_, COM_, EN, or IN_ exceeding V+ or V- are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
Note 2: All leads are soldered or welded to PC boards.
+25°C
C, E
C, E
C, E
C, E
+25°C
C, E
C, E
+25°C
C, E
C, E
+25°C
C, E
+25°C
+25°C
C, E
T
A
ANALOG SWITCH
LOGIC INPUT
±
±