Datasheet
Power-Supply Voltage (V
DD
to V
SS
).........................-0.3V to +6V
All Other Pins...................................(V
SS
- 0.3V) to (V
DD
+ 0.3V)
Output Short-Circuit Duration
(OUT shorted to V
SS
or V
DD
).................................Continuous
Continuous Power Dissipation (T
A
= +70°C)
5-Pin SC70 (derate 3.1mW/°C above +70°C)............. 247mW
6-Pin SC70 (derate 3.1mW/°C above +70°C)..............245mW
5-Pin SOT23 (derate 3.1mW/°C above +70°C)
...........
247mW
6-Pin SOT23 (derate 8.7mW/°C above +70°C)
...........
696mW
8-Pin SOT23 (derate 5.1mW/°C above +70°C)
...........
408mW
8-Pin μMAX (derate 4.5mW/°C above +70°C)
............
362mW
8-Pin SO (derate 5.9mW/°C above +70°C)
................
471mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C).........727mW
14-Pin SO (derate 8.33mW/°C above +70°C)
.............
667mW
Operating Temperature Range .........................-40°C to +125°C
Military Operating Temperature Range
..
.............-55°C to +110°C
Junction Temperature
.
...........................
................
.............150°C
Storage Temperature Range
..
.............................-65°C to +150°C
Lead Temperature (soldering, 10s)
..
...............................+3000°C
Soldering Temperature (reflow)
.
..................
.....................+240°C
(V
DD
= +5V, V
SS
= 0V, V
CM
= 0V, V
OUT
= V
DD
/2, R
L
≥ 1MΩ connected to V
DD
/2, SHDN = V
DD
(MAX4481 only), T
A
= +25°C, unless
otherwise noted.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Supply Voltage Range V
DD
Inferred from PSRR test 2.5 5.5 V
Supply Current per Amplier I
DD
V
DD
= 2.5V 45
μA
V
DD
= 5.0V 50 100
Supply Current in Shutdown I
SHDN
SHDN = V
SS
(MAX4481 only) 0.05 0.5 μA
Input Offset Voltage V
OS
±1 ±5.5 mV
Input Bias Current I
B
(Note 1) ±0.1 ±100 pA
Input Offset Current I
OS
(Note 1) ±0.1 ±100 pA
Input Resistance R
IN
Differential or common mode 1000 MΩ
Input Common-Mode Voltage
Range
V
CM
Inferred from CMRR test V
SS
V
DD
-
1.3
V
Common-Mode Rejection Ratio CMRR V
SS
≤ V
CM
≤ V
DD
- 1.3V 71 86 dB
Power-Supply Rejection Ratio PSRR 2.5V ≤ V
DD
≤ 5.5V 82 92 dB
Large-Signal Voltage Gain A
VOL
V
SS
+ 0.02V ≤ V
OUT
≤ V
DD
- 0.03V
R
L
= 100kΩ 110
dB
V
SS
+ 0.10V ≤ V
OUT
≤ V
DD
- 0.20V
R
L
= 5kΩ 94 105
Output Voltage High V
OH
Specied as
V
DD
- V
OUT
R
L
= 100kΩ 4
mV
R
L
= 5kΩ 80 150
Output Voltage Low V
OL
Specied as
V
OUT
- V
SS
R
L
= 100kΩ 1
mV
R
L
= 5kΩ 8 30
Output Short-Circuit Current I
SC
Sourcing 3
mA
Sinking 17
Shutdown Mode Output Leakage I
OUTSHDN
Device in shutdown mode, SHDN = V
SS
,
V
SS
< V
OUT
< V
CC
(MAX4481 only)
±0.01 ±0.1 μA
SHDN Logic Low V
IL
MAX4481 only 0.3 x V
DD
V
SHDN Logic High V
IH
MAX4481 only 0.7 x V
DD
V
SHDN Input Current I
IL
, I
IH
SHDN = V
DD
or V
SS
(MAX4481 only) ±0.001 ±1 ±500 nA
Gain-Bandwidth Product GBW 140 kHz
MAX4480–MAX4483 Single/Dual/Quad, Low-Cost, Single-Supply,
Rail-to-Rail Op Amps with Shutdown
www.maximintegrated.com
Maxim Integrated
│
2
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics