Datasheet
High-Output-Drive, Precision, Low-Power, Single-
Supply, Rail-to-Rail I/O Op Amps with Shutdown
MAX4165–MAX4169
ABSOLUTE MAXIMUM RATINGS
DC ELECTRICAL CHARACTERISTICS
(V
CC
= +2.7V to +6.5V, V
EE
= 0V, V
CM
= 0V, V
OUT
= (V
CC
/ 2), R
L
= 100kΩ to (V
CC
/ 2), V
SHDN
≥ 2V, T
A
= +25°C, unless otherwise
noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage (V
CC
to V
EE
)....................................................7V
IN_+, IN_-, SHDN_............................(V
EE
- 0.3V) + (V
CC
+ 0.3V)
OUT_ (shutdown mode) ...................(V
EE
- 0.3V) + (V
CC
+ 0.3V)
Output Short-Circuit Duration to V
CC
or V
EE
(Note 1) .....Continuous
Continuous Power Dissipation (T
A
= +70°C)
5-Pin SOT23 (derate 7.10mW/°C above +70°C)..........571mW
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin µMAX (derate 4.10mW/°C above +70°C) ...........330mW
8-Pin µDFN (derate 4.8mW/°C above +70°C) .............380mW
10-Pin µMAX (derate 5.60mW/°C above +70°C) ..........444mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C) 800mW
14-Pin SO (derate 8.33mW/°C above +70°C)...............667mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
MAX416_EPA/EPD
0.25 0.85
mV
MAX416_ESA/ESD
0.25 0.85
Input Offset Voltage V
OS
V
CM
= V
EE
to V
CC
MAX416_EUA/EUB/ELA
0.35 1.7
MAX416_EUK
0.35 1.5
MAX4169E_D
0.25 1.0
Input Bias Current I
B
V
CM
= V
EE
to V
CC
±50 ±150 nA
Input Offset Current I
OS
V
CM
= V
EE
to V
CC
±1 ±15 nA
Differential Input Resistance R
IN(DIFF)
| V
IN
+ - V
IN
- | 1.8V
kΩ
| V
IN
+ - V
IN
- | > 1.8V
2
Common-Mode Input
Voltage Range
V
CM
Inferred from CMRR test V
EE
- 0.25 V
CC
+ 0.25 V
MAX416_EPA/EPD
72 93
dB
Common-Mode
Rejection Ratio
CMRR
V
EE
- 0.25V <
V
CM
< (V
CC
+ 0.25V)
MAX416_ESA/ESD
72 93
MAX416_EUA/EUB/ELA
62 89
MAX416_EUK
63 90
MAX4169E_D
71 93
MAX416_EPA/EP
D 72 88
dB
MAX416_ESA/ESD
72 88
Power-Supply Rejection Ratio PSRR V
CC
= 2.7V to 6.5V
MAX416_EUA/EUB/ELA
72 86
MAX416_EUK
72 86
MAX4169E_D
70 88
Output Resistance R
OUT
A
VCL
= +1V/V 0.1
Off-Leakage Current
in Shutdown
I
OUT(SHDN)
V
SHDN
< 0.8V, V
OUT
= 0V to V
CC
±0.001 ±2 μA
Large-Signal Voltage Gain A
VOL
V
CC
= 5V
V
OUT
= 0.2V to 4.8V, R
L
= 100k 95 120
dB
V
OUT
= 0.6V to 4.4V, R
L
= 25 71 83
≤
Ω
Ω
kΩ
500
Note 1: Continuous power dissipation should also be observed.
2 _______________________________________________________________________________________