Datasheet

MAX4004/MAX4006
High-Accuracy, High-Side Current Monitors
in SOT23
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
CLAMP to GND ......................................................-0.3V to +25V
BIAS, REF to GND ..................................................-0.3V to +25V
OUT to GND .........................................-0.3V to (V
CLAMP
+ 0.6V)
Short-Circuit, REF to GND..........................................Continuous
Current into any Pin ..........................................................±30mA
Continuous Power Dissipation (T
A
= +70°C)
6-Pin SOT23 (derate 8.7mW/°C above +70°C)............696mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(V
BIAS
= 5V, GND = 0V, REF = Open, V
OUT
= 0V (MAX4004), CLAMP = Open, T
A
= -40°C to +85°C. Typical values are at T
A
= +25°C,
unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS MIN TYP MAX
UNITS
Bias Voltage Range V
BIAS
Inferred from power-supply
rejection test
2.7 22 V
I
REF
= 250nA 40 100 µA
Bias Quiescent Current I
BIAS
I
REF
= 2.5mA 3.6 4 mA
Reference Voltage V
REF
I
REF
= 2.5mA
V
BIAS
- 1.1 V
BIAS
- 0.8
V
Thermal Shutdown
Engage Temperature
T
SHDN
REF shorted to GND, junction
temperature rising
150 °C
Trip-Point Temperature
Hysteresis
T
HYS
REF shorted to GND, junction
temperature falling
5 °C
Input Current Limit I
LIM
V
REF
= V
BIAS
- 5V 20 mA
I
REF
= 250nA
0.3
f = 0.1Hz to 10Hz
I
REF
= 2.5mA
63
I
REF
= 250nA
9.2
MAX4004
Output Current Noise
i
NOUT
f = 0.1Hz to 10kHz
I
REF
= 2.5mA
1240
pA
RMS
I
REF
= 250nA
0.041
f = 0.1Hz to 10Hz
I
REF
= 2.5mA
0.63
I
REF
= 250nA
1.3
MAX4006
Output Voltage Noise
e
NOUT
f = 0.1Hz to 10kHz
I
REF
= 2.5mA
12.5
µV
RMS
I
REF
= 250nA
50 GΩ
MAX4004
I
REF
= 2.5mA
5MΩ
Output Resistance R
OUT
MAX4006 10 kΩ
Output Leakage REF = open 1 pA
Output Voltage Range V
OUT
V
BIA S
= 2.7V to 22V , I
RE F
= 0 to 1m A,
MAX4004: ∆I
OUT
/I
OUT
= ±1%,
MAX4006: ∆V
OUT
/I
OUT
= ±1%
0 to V
BIAS
- 1.5
0 to V
BIAS
- 0.85
V