Datasheet

MAX312L/MAX313L/MAX314L
10
ΩΩ
, Quad, SPST, +3V Logic-Compatible
Analog Switches
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS—Single Supply (continued)
(V+ = +12V, V- = 0, GND = 0, V
IH
= 2.0V, V
IL
= 0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
(Notes 2, 3)
PARAMETER
SYMBOL
CONDITIONS T
A
MIN TYP MAX
UNITS
+25°C 0.3 2
On-Resistance Match Between
Channels (Note 4)
ΔR
ON
I
COM_
= 10mA,
V
NO_
or V
NC_
= +10V
T
MIN
to T
MAX
2.5
Ω
+25°C 1.7 3.5
On-Resistance Flatness
(Note 5)
R
FLAT
(
ON
)
I
COM_
= 10mA,
V
NO_
or V
NC_
= +2V,
+6V, +10V
T
MIN
to T
MAX
4.5
Ω
DYNAMIC
+25°C
165 325
Turn-On Time t
ON
V
COM_
= 8V, R
L
= 300Ω,
C
L
= 35pF, Figure 1
T
MIN
to T
MAX
425
ns
+25°C
117 175
Turn-Off Time t
OFF
V
COM_
= 8V, R
L
= 300Ω,
C
L
= 35pF, Figure 1
T
MIN
to T
MAX
225
ns
Break-Before-Make Time Delay
(MAX314L only, Note 7)
t
D
R
L
= 300Ω, C
L
= 35pF,
Figure 2
+25°C 1 5 ns
Charge Injection Q
Figure 3, C
L
= 1.0nF,
V
GEN
= 0, R
GEN
= 0
+25°C -10 pC
LOGIC INPUT
Input Logic High V
IH
2.0 V
Input Logic Low V
IL
0.8 V
Input Current with Input Logic
High
I
INH
IN_ = 2.0V
-0.5 0.005
0.5 µA
Input Current with Input Logic
Low
I
INL
IN_ = 0.8V
-0.5 0.005
0.5 µA
POWER SUPPLY
Power-Supply Range V+
+4.5 +36
V
+25°C
0.01
1
V+ = +13.2V, V
IN
= 0 or V+
T
MIN
to T
MAX
5
+25°C 25
125
Positive Supply Current I+
V+ = +13.2V, V
IN
= 5V
T
MIN
to T
MAX
175
µA
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: -40°C specifications are guaranteed by design.
Note 4: ΔR
ON
= ΔR
ON
max - ΔR
ON
min.
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7: Guaranteed by design.
Note 8: Off-isolation = 20log
10
[V
COM
/(V
NC
or V
NO
)], V
COM
= output, V
NC
or V
NO
= input to off switch.
Note 9: Between any two switches.