Datasheet

INPUT
Input Current with
I
INH
V
IN
_
= 2.4V, all others = 0.8V
-1.000 0.005 1.000 µA
Input-Voltage High
Input Current with
I
INH
V
IN
_
= 0.8V, all others = 2.4V
-1.000 0.005 1.000 µA
Input-Voltage Low
SUPPLY
Power-Supply Range ±4.5 ±20 V
Positive Supply Current
T
A
= +25°C -1.00 0.01 1.00
I+
T
A
= T
MIN
to T
MAX
-5.00 5.00
µA
Negative Supply Current I-
T
A
= +25°C -1.00 -0.01 1.00
T
A
= T
MIN
to T
MAX
-5.00 5.00
µA
Logic-Supply Current I
L
T
A
= +25°C -1.00 0.01 1.00
T
A
= T
MIN
to T
MAX
-5.00 5.00
µA
Ground Current I
GND
T
A
= +25°C -1.00 -0.01 1.00
T
A
= T
MIN
to T
MAX
-5.00 5.00
µA
DYNAMIC
Turn-On Time t
ON
Figure1 T
A
= +25°C 100 150 ns
Turn-Off Time t
OFF
Figure 1 T
A
= +25°C 60 100 ns
Break-Before-Make
t
D
MAX303 only,
T
A
= +25°C 10 20 ns
Time Delay (Note 3) Figure 2
C
L
= 10nF, V
GEN
= 0V,
Charge Injection Q R
GEN
= 0Ω,T
A
= +25°C 10 15 pC
(Note 3) Figure 3
Off-Isolation (Note 5) OIRR
R
L
= 100Ω, C
L
= 5pF,
T
A
= +25°C 72 dB
f = 1MHz, Figure 4
Crosstalk (Note 6)
R
L
= 50Ω, C
L
= 5pF,
T
A
= +25°C 90 dB
f = 1MHz, Figure 5
Off-Capacitance
C
OF
f = 1MHz, Figure 6 T
A
= +25°C 12 pF
COM Off-Capacitance
C
COM(OFF
f = 1MHz, Figure 6 T
A
= +25°C 12 pF
Channel-On Capacitance C
COM(ON)
f = 1MHz, Figure 7 T
A
= +25°C 39 pF
MAX301/MAX303/MAX305
Precision, Dual, High-Speed Analog Switches
_________________________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, V- = -15V, V
L
= +5V, GND = 0V, V
INH
= +2.4V, V
INL
= +0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER SYMBOL CONDITIONS
MIN TYP MAX
UNITS
(Note 2)
All channels on or off,
V
IN
= 0V or 5V,
V+ = 16.5V, V- = -16.5V
All channels on or off,
V
IN
= 0V or 5V,
V+ = 16.5V, V- = -16.5V
All channels on or off,
V
IN
= 0V or 5V,
V+ = 16.5V, V- = -16.5V
All channels on or off,
V
IN
= 0V or 5V,
V+ = 16.5V, V- = -16.5V
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used on
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆R
ON
= ∆R
ON
MAX - ∆R
ON
MIN. On resistance match between channels and flatness are guaranteed only with
specified voltages.
Note 5: See Figure 4. Off isolation = 20log
10
V
COM
/V
NC or
V
NO
, V
COM
= output, V
NC or
V
NO
= input to off switch.
Note 6: Between any two switches. See Figure 5.