Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsDev KitsPCB design board

Table Of Contents

Evaluates: MAX14626

MAX14626 Evaluation Kit

General Description

The MAX14626 evaluation kit (EV kit) is a fully assembled

and tested circuit board that demonstrates the MAX14626

high-voltage 4–20mA current-loop protector.

Benets and Features

● Evaluates Current-Limit Protection

● Proven PCB Layout

● Fully Assembled and Tested

19-6802; Rev 0; 9/13

Ordering Information appears at end of data sheet.

*EP = Exposed pad.

Note: Indicate that you are using the MAX14626 when contacting these component suppliers.

DESIGNATION QTY DESCRIPTION

C1, C2 2

1µF ±10%, 50V X5R ceramic

capacitors (0805)

Taiyo Yuden UMK212BJ105KG-T

JU1–JU8 8 2-pin single-row headers

R1 1

200Ω±1%,0.5Wresistor(1210)

R2 1 499Ω±1%,0.5Wresistor(1210)

R3 1 1kΩ±1%,0.5Wresistor(1210)

R4 1 2kΩ±1%,0.5Wresistor(1210)

R5 1

5kΩ1Wpotentiometer

Bourns3290W-1-502

R6, R7 2 499Ω±0.1%resistors(0805)

DESIGNATION QTY DESCRIPTION

TB1, TB2 2

Terminal blocks

Molex 39357-0002

TP1, TP3, TP5 3 Red test points

TP2, TP4, TP6 3 Black test points

U1 1

4–20mA current-loop protector

(6 TDFN-EP*)

Maxim MAX14626ETT+

(Top Mark: AVF)

— 8 Shunts

— 1 PCB: MAX14626 EVKIT

SUPPLIER PHONE WEBSITE

Bourns, Inc. 408-496-0706 www.bourns.com

Molex 800-786-6539 www.molex.com

Taiyo Yuden 800-348-2496 www.t-yuden.com

Component List

Component Suppliers

Summary of content (6 pages)

PAGE 1
Evaluates: MAX14626 MAX14626 Evaluation Kit General Description The MAX14626 evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the MAX14626 high-voltage 4–20mA current-loop protector. Benefits and Features ● Evaluates Current-Limit Protection ● Proven PCB Layout ● Fully Assembled and Tested Ordering Information appears at end of data sheet.
PAGE 2
Evaluates: MAX14626 MAX14626 Evaluation Kit Quick Start Required Equipment ● MAX14626 EV kit ● 25V DC power supply ● Ammeter Procedure The EV kit is fully assembled and tested. Follow the steps below to verify board operation: 1) Verify that all jumpers are in their default positions, as shown in Table 1. 2) Install shunts on jumpers JU7 and JU8. 3) Connect one side of the ammeter to 25V power supply and the other side to TP1 to measure the current going through the device and load.
PAGE 3
MAX14626 Evaluation Kit Evaluates: MAX14626 Figure 1. MAX14626 EV Kit Schematic www.maximintegrated.
PAGE 4
Evaluates: MAX14626 MAX14626 Evaluation Kit 1.0’’ Figure 2. MAX14626 EV Kit Component Placement Guide— Component Side 1.0’’ Figure 3. MAX14626 EV Kit PCB Layout—Component Side 1.0’’ Figure 4. MAX14626 EV Kit PCB Layout—Solder Side www.maximintegrated.
PAGE 5
MAX14626 Evaluation Kit Evaluates: MAX14626 Ordering Information PART TYPE MAX14626EVKIT# EV Kit #Denotes RoHS compliant. www.maximintegrated.
PAGE 6
Evaluates: MAX14626 MAX14626 Evaluation Kit Revision History REVISION NUMBER REVISION DATE 0 9/13 DESCRIPTION Initial release PAGES CHANGED — For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied.