Datasheet

DS4100H
100MHz HCSL Clock Oscillator
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
CC
= 3.135V to 3.465V, T
A
= -40°C to +85°C. Typical values are at V
CC
= +3.3V and T
A
= +25°C, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Power-Supply Voltage (V
CC
) .......................................-0.3V, +4V
Continuous Power Dissipation (T
A
= +70°C) ...................280mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range ...............................-40°C to +85°C
Soldering Temperature Profile
(3 passes max) .......................................................Refer to the
IPC/JEDEC J-STD-020 specification.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Supply Voltage V
CC
(Note 1) 3.135 3.300 3.465 V
Supply Current I
CC
OE = V
IH
, Figure 2 71 85 mA
Input High Voltage (OE) V
IH
(Note 1) 2.0 V
CC
V
Input Low Voltage (OE) V
IL
(Note 1) 0 0.8 V
Input Leakage Current
(OE)
I
IN
GND  OE  V
CC
-55 +10 μA
HCSL OUTPUTS (OUTP, OUTN)
Output High Current I
OH
475 resistor connected between RREF and GND, V
OUTN
or V
OUTP
= 1.2V, V
CC
= 3.3V ±5%
12.25 13.92 15.59 mA
Output High Voltage V
OH
R
S
= 0, R
T
= 50 (Notes 1, 2) 612.5 696.0 779.5 mV
Output Low Voltage V
OL
R
S
= 0, R
T
= 50 (Notes 1, 2) 0 50 mV
Output Leakage High
Current
I_
LEAKH
V
OE
= 0; V
OUTN
, V
OUTP
= V
CC
-10 +10 μA
Output Leakage Low
Current
I_
LEAKL
V
OE
= 0; V
OUTN
, V
OUTP
= 0 -10 +10 μA
Output Resistance R
O
Measure current out of OUTN pin at V
OUTN
= 0.5V and 1.0V;
R
O
= 0.5 / I
0.5
- I
1.0
3000 
Crossover Voltage V
CROSS
Measure crossing voltage at OUTP and OUTN
(Notes 1, 2, and 3)
(50% x
V
OH
) ±5%
mV
Output Rise Time t
R
20% to 80%, CL = 2pF 175 700 ps
Output Fall Time t
F
80% to 20%, CL = 2pF 175 700 ps
Overshoot V
OVER
Measure overshoot voltage at OUTP and OUTN
(Notes 1, 2, and 3)
V
OH
+
0.2V
V
Undershoot V
UNDER
Measure undershoot voltage at OUTP and OUTN
(Notes 1, 2, and 3)
-0.2 V
Output-Enable Time to
Low Level
t
PZL
Figure 3 (Note 4) 200 ns
Output-Enable Time to
High Level
t
PZH
Figure 3 (Note 5) 200 ns