Datasheet

71M6543F/71M6543G Data Sheet
82 v2
Wake Enable Wake Flag
De-bounce Description
Name
Location
Name
Location
Always Enabled
WF_OVF
28B0[4]
No
Wake after WD reset.
Always Enabled
WF_CSTART
28B0[7] No
Wake after cold start - the first
application of power.
Always Enabled
WF_BADVDD
28B0[2] No
Wake after insufficient VBAT
voltage.
*This pin is sampled every 2 ms and must remain high for 64 ms to be declared a valid high level. This pin is high-
level sensitive.
Table 64: Wake Bits
Name
Location
RST
WK
Dir
Description
EW_DIOR
28B3[2] 0 – R/W
Connects SEGDIO4 to the WAKE logic and permits
SEGDIO4 rising to wake the part. This bit has no effect
unless SEGDIO4 is configured as a digital input.
EW_DIO52
28B3[1] 0 – R/W
Connects DIO52 to the WAKE logic and permits DIO52
high level to wake the part. This bit has no effect unless
DIO52 is configured as a digital input.
EW_DIO55
28B3[0] 0 – R/W
Connects DIO55 to the WAKE logic and permits DIO55
high level to wake the part. This bit has no effect unless
DIO55 is configured as a digital input.
WAKE_ARM
28B2[5] 0 – R/W
Arms the WAKE timer and loads it with the value in
WAKE_TMR (I/O RAM 0x2880) register. When SLP or
LCD mode is asserted by the MPU, the WAKE timer
becomes active.
EW_PB
28B3[3] 0 – R/W
Connects the PB pin to the WAKE logic and permits PB
high level to wake the part. PB is always configured as
an input.
EW_RX
28B3[4] 0 – R/W
Connects the RX pin to the WAKE logic and permits
RX rising to wake the part. See 3.4.1 for de-bounce
issues.
WF_DIO4
28B1[2] 0 – R
SEGDIO4 flag bit. If SEGDIO4 is configured to wake
the part, this bit is set whenever SEGDIO4 rises. It is
held in reset if SEGDIO4 is not configured for wakeup.
WF_DIO52
28B1[1] 0 – R
SEGDIO52 flag bit. If SEGDIO52 is configured to wake
the part, this bit is set whenever SEGDIO52 is a high
level. It is held in reset if SEGDIO52 is not configured
for wakeup.
WF_DIO55
28B1[0] 0 – R
SEGDIO55 flag bit. If SEGDIO55 is configured to wake
the part, this bit is set whenever SEGDIO55 is a high
level. It is held in reset if SEGDIO55 is not configured
for wakeup.
WF_TMR
28B1[5]
0
–
R
Indicates that the Wake timer caused the part to wake up.
WF_PB
28B1[3]
0
–
R
Indicates that the PB pin caused the part to wake.
WF_RX
28B1[4]
0
–
R
Indicates that RX pin caused the part to wake.
WF_RST
WF_RSTBIT
WF_ERST
WF_CSTART
WF_BADVDD
28B0[6]
28B0[5]
28B0[3]
28B0[7]
28B0[2]
*
*
*
*
*
– R
Indicates that the RST pin, E_RST pin, RESET bit (I/O
RAM 0x2200[3]), the cold start detector, or low voltage
on the VBAT pin caused the part to reset.
*See Table 65 for details.