MAXDATA PLATINUM 7200 IR M6 User’s Manual
Contents
Contents 1 Safety Information 7 Safety Warnings and Cautions ................................................................................................................7 Intended Application Uses ......................................................................................................................7 General Warnings ....................................................................................................................................8 Place Battery Marking ................
Setup Alias Keys ....................................................................................................................................38 Limitations .............................................................................................................................................38 Interface to Server Management ..........................................................................................................38 Sample Setup for Console Redirection ...........................
Installing and Removing Memory Boards .............................................................................................68 Removing Memory Board Air Baffle ................................................................................................69 Installing Memory Board Air Baffle ..................................................................................................69 Hot Removal of a Memory Board.................................................................................
Figures 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. PLATINUM 7200 IR Server Front View ...........................................................................................13 Front Components ..........................................................................................................................15 Front Panel Controls and Indicators ................................................................................................16 Local Control Panel ..................................
1 Safety Information This document applies to MAXDATA PLATINUM Server Boards, MAXDATA PLATINUM Server Chassis (pedestal and rack-mount) and installed peripherals. To reduce the risk of bodily injury, electrical shock, fire, and equipment damage, read this document and observe all warnings and precautions in this guide before installing or maintaining your MAXDATA PLATINUM server product.
General Warnings The power supply in this product contains no user-serviceable parts. There may be more than one supply in this product. Refer servicing only to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC cord for each supply. The DC push-button on/off switch on the front panel does not turn off system AC power.
Site Selection The system is designed to operate in a typical office environment. Choose a site that is: • Clean, dry, and free of airborne particles (other than normal room dust). • Well-ventilated and away from sources of heat including direct sunlight and radiators. • Away from sources of vibration or physical shock. • Isolated from strong electromagnetic fields produced by electrical devices.
Power Cord Warnings If an AC power cord was not provided with your product, purchase one that is approved for use in your country.
Rack Mount Warnings The equipment rack must be anchored to an unmovable support to prevent it from tipping when a server or piece of equipment is extended from it. The equipment rack must be installed according to the rack manufacturer’s instructions. Install equipment in the rack from the bottom up, with the heaviest equipment at the bottom of the rack. Extend only one piece of equipment from the rack at a time. You are responsible for installing a main power disconnect for the entire rack unit.
Laser Peripherals or Devices CAUTION To avoid risk of radiation exposure and/or personal injury: • Do not open the enclosure of any laser peripheral or device. • Laser peripherals or devices are not user serviceable. • Return to manufacturer for servicing.
2 Platform Description The PLATINUM 7200 IR Server is a compact, high-density, rack-mount system with support for one to four Intel® Xeon™ processors and 64 GB of DDR2 400 MHz SDRAM memory. The system is based on the PLATINUM 7200 IR Server Board using the Intel® E8501 chipset. The platform supports hot plug PCI-X and PCI-Express add-in cards; hot-swap, redundant power supply modules; hot swap, redundant cooling fans, hot-plug memory with RAS features, and hot-swap hard disk drives.
Platform Features The platform features are outlined in the following table. Table 2. Chassis Feature Summary 14 Feature Description Dimensions (4U rackmount platform) Height: 6.8 inches (173 mm) Width: 17.6 inches (447 mm) Depth: 27.
Platform Front A B G F C D E F Figure 2. Front Components Table 3. Front Components Item Description A. CD-ROM / DVD-ROM drive bay B. 5 ¼ peripheral bay C. Video connector D. USB 2.0 ports E. Front control panel. Standard control panel shown. F. Hot-swap fan modules G.
Standard Control Panel The standard control panel provides a user interface for system management via switches and status LEDs. The control panel also contains the speaker. Figure 3 shows the location of the buttons and status LEDs on the standard control panel. A B I C D E F J G H K L Figure 3. Front Panel Controls and Indicators Table 4.
Item Feature Description F System Status/Fault LED (Green/Amber) Indicates system status. G System Power LED (Green) LED State Description Off Not ready AC Power Off, POST error Green, On Ready System booted and ready Green, Blinking Degraded CPU or DIMM disabled Amber, On Critical Alarm Critical Power Supply, Blower, Voltage, or Temperature failure Amber, Blinking Non-Critical Alarm Redundant Power Supply or Blower failure. NonCritical Blower, Voltage, and Temperature failure.
Local Control Panel A B C D E M L K J I H G F Figure 4. Local Control Panel Table 5. Local Control Panel Item Feature Description A LCD display Video display B Scroll up button Press to scroll up on the LCD. C Scroll down button Press to scroll down on the LCD. D Back button Press to move to the previous LCD screen. E Select button Press to enter a command or select an option on the LCD. F System ID LED (Blue) Helps identify the system via server management.
Item Feature Description L Hard Drive Status LED (Green/Amber) Indicates hard drive activity and fault status. M System Reset button MAXDATA PLATINUM 7200 IR M6 Green On A hard drive is being initialized. Green Blinking A hard drive is active. Amber On Hard drive/slot failure. Amber Slow Blinking (~1 Hz) A predictive hard drive/slot failure or rebuild in process. Amber Fast Blinking (~2.5 Hz) Hard drive rebuild interrupted or rebuild on empty slot. Resets the system.
Platform Rear Figure 5 shows the features on the chassis back panel. B A 1 2 3 4 C 5 6 7 K I E F G D H1 J L H2 Figure 5. Rear Platform Features Table 6. Rear Platform Features Item Description A Serial port connector. Emergency Management Port access is provided through the serial port.
Processors The PLATINUM 7200 IR Server supports from one to four physical processors, either 64-bit Intel® Xeon™ processor MP with 1 MB L2 Cache, 64-bit Intel® Xeon™ processor MP with 8 MB L3 Cache, or Dual-Core Intel® Xeon™ processor 7000 sequence. These processors are targeted for multiprocessor servers.
Available Memory Configurations Four memory configurations are available in the BIOS Setup utility. • Maximum Performance: Maximum Performance is the default configuration in BIOS setup. With this configuration, the BIOS first attempts to configure the Memory Boards as fourway interleaved. If four-way interleaving cannot be accomplished, it will attempt to two-way interleave. It will then use one-way interleaving if any remaining memory cannot be fourway or two-way interleaved.
The server BIOS also includes two additional memory reliability, accessibility, and serviceability (RAS) features: • Memory Sparing: A rank on each Memory Board can be reserved as a “spare” and can only be used as a backup for other ranks on the same Memory Board. The memory rank that is configured as spare is held in reserve and cannot be used by the operating system. Hot removal cannot be performed when in a Memory Sparing configuration.
Power Subsystem The power subsystem consists of the following: • Power supply modules • Plug-in VRM converters • The Power Distribution Board The power subsystem can be configured with two power supply modules installed for 1+1 redundancy at 220 VAC. Power Supply Modules The output rating of the power supply is 1470 W when operated between 170 VAC and 264 VAC. It is a current-sharing power supply with auto-ranging input. The power supply is approximately 7.75 inches wide by 13.5 inches deep by 1.
Each power supply module has three status LEDs. These are located next to the input connector, as shown by the following figure. A B C Figure 6. Power Supply Indicators Table 7. Power Supply Indicators Location Purpose Description A (left) Power Good LED (green) This green LED is driven by internal circuitry and is lit whenever the power is turned on. B (center) Fault LED (amber) This amber LED is driven by internal circuitry and is lit when a power rail has failed.
Cooling Subsystem CAUTION The chassis top cover must be installed for proper system cooling. Cooling components must be hotswapped within two minutes. This time period applies only to the time that the cooling component is physically removed, not from the time of failure. The cooling subsystem consists of hot-swap, redundant (2+2) fans. In the event of a cooling component failure, system cooling is maintained and the system continues to operate while the component is being hot swapped.
Peripherals Hot-Swap SCSI Hard Disk Drive Support The hot-swap hard disk drive carrier accommodates 15,000-RPM or slower Ultra320 SCSI SCA-type hard disk drives. The SCSI Backplane Board supports Low Voltage Differential (LVD) SCSI disk drives only. SingleEnded (SE) SCSI devices are not supported internally. SE drives are only supported on the external SCSI connector. A B Figure 7. Hard Disk Drive Carrier Table 10.
Platform Board Set The board set consists of the following boards: • One Main Board • One to four Memory Boards In addition, the server contains the following system boards: 28 • Front Panel Board • SCSI Backplane Board • Power distribution Board • SATA-to-IDE Adapter Board Platform Description
Main Board The Main Board consists of the Intel® E8501 chipset, four Memory Board connectors, and slots for PCI-Express and PCI-X adapters. The board also has support for the Management Module - Professional or Advanced, a dedicated Fibre Channel module connector, on-board video, gigabit Ethernet, USB2.0, Serial-ATA, Ultra320 SCSI, dual flash memory components for BIOS, and RAID On Motherboard (ROMB).
Table 11. Main Board Component Locations Item Description Item Description A Generic Communication Module (GCM) R Memory Board Slot B B RAID Activation Key S DC power connectors C PCI-X 100 MHz (Slot 7) T Power Distribution Board (PDB) signal connector D PCI-X 100 MHz (Slot 6) U Processor socket 1 E PCI Express x4 - Hot Plug (Slot 5) V Processor socket 2 F PCI Express x4 - Hot Plug (Slot 4) W Processor socket 4 G PCI Express x4 - Hot Plug (Slot 3) X VRM 10.
• Integrated ATI Technologies Inc Radeon 7000 with 16 MB embedded SDRAM • Fibre Channel Module with a 64-bit PCI-X 100 Mhz interface • Broadcom BCM5704C Gigabit Ethernet Controller with dual-ports • Server Management LAN Port (RJ45) • USB 2.
Memory Board Up to four Memory Boards can be installed. Each Memory Board has four DIMM sockets and supports two DDR2 channels with two DIMMs per channel. The Memory Boards support both single-rank and double-rank registered DIMMs. Unbuffered DIMMs are not supported. The Memory Boards connect to the Main Board through x16 PCI-Express connectors. The Independent Memory Interface (IMI) bus connects the XMB on the Memory Board and the Intel® E8501 on the Main Board.
3 Starting Up and Shutting Down the Server Plugging the Server into AC Power When the server is plugged into the AC power the server will power cycle after a 30 seconds delay. This is required to initialize the Out Of Band functionality of the BMC. Once the server completed the power cycle, the server can be powered on using the power button on the front control panel. NOTE When installing a new Management Module remember to update the BMC with the correct server firmware.
Shutting Down the Server 1. Exit the operating system (if applicable) 2. Press and hold the power button until the server shuts down. CAUTION Powering down the server with the power button does not remove all power from the system. The +3.3 V standby power is still available to the system even when it is not running. To remove standby power from the system, unplug all power cords from the system and unplug the power supplies.
4 Server Platform Utilities BIOS Setup Utility The BIOS Setup Utility is a text-based utility that allows you to configure the system and view and change device settings and view environmental information for the platform. The BIOS Setup Utility interface consists of several screens, called pages. Each page contains information or links to other pages. The first page in Setup displays links for general categories. These links lead to pages containing specific configuration settings.
Keyboard Commands The bottom right portion of the Setup screen provides a list of commands that are used to navigate through the BIOS Setup Utility. These commands are context sensitive. The Keyboard Command Bar supports the following key presses: Table 14.
Key Option Description Setup Defaults Pressing causes the following to appear: Load default configuration now? (Y/N) If the “Y” key is pressed, all Setup fields are set to their default values.
Keystroke Mappings During console redirection, the remote terminal (which may be a dumb terminal or a system with a modem running a communication program) sends keystrokes to the local server. The local server passes video back over this same link. The keystroke mappings follow VT-UTF8 format with the following extensions. Setup Alias Keys The and - combinations are synonyms for the or “Setup” key. These are not prompted for in screen messages.
Console Configuration 1. Boot the console into the operating system. 2. Click the Start button in the task bar. 3. Select Programs > Accessories > Communications and click “Hyperterminal”. 4. At the Connection Description window, enter “guest” for the name and click “Ok”. 5. At the Connect To window, select the COM port of the console that the Null modem is connected. In this example, it is COM1. 6.
LSI Logic MPT SCSI Utility The LSI Logic MPT SCSI Utility provides a way to configure SCSI features. This configuration utility is accessed by pressing - during POST, right after the memory test but before entering the System Options Menu screen. Press to select “Menu”. This provides access to the menu options “Boot Adapter List” and “Global Properties”. The boot adapter list allows you to add or remove boot adapters.
The Device Properties Menu shows options for devices attached to the adapter. It is a large menu and requires the use of the arrow keys to move fully to the left and fully down to see all configuration options. Slide bars at the right and on the bottom of the screen help define your location in the menu.
System Configuration Wizard (SCW) The System Configuration Wizard (SCW) is a combination of software applications, batch files and helper applications that help you with the initial configuration of your MAXDATA PLATINUM server. The SCW supports IPMI 2.0, 1.5, and later compatible platforms. It performs the following activities: • Sets the system time and date in the BIOS. • Loads Field Replaceable Units (FRUs), Sensor Data Records (SDRs). • Sets the System Asset Tag.
Starting the System Configuration Wizard To run the SCW, boot your server from the Server Deployment Toolkit CD. The Start screen provides a brief description of the Server Configuration Wizard.
• Load SDRs only onto this server: When this box is checked, the SCW will ask you questions about the SDRs and will load them based on how you answer those questions. • Load FRUs and SDRs onto this server: The FRUs and SDRs are loaded based on the master.cfg file found in the \FRUSDR folder in the Server Deployment Toolkit CD. • Configure this server with a System Asset Tag: When this box is checked, the SCW will ask you questions about the system asset tag to assign to the system.
Configuring Channels The Channels configuration screen provides a way for you to configure the various channels in the system. If your server has the Management Module - Professional Edition, one LAN channel and one serial modem channel are supported. If your server has the Management Module - Advanced Edition, your server supports one LAN channel, one serial modem channel, and one advanced LAN channel. The LAN Channel configuration provides a way to configure the individual LAN channel(s) on the system.
• Gateway IP Address: The Gateway IP Address edit box allows you to enter the Gateway IP address for this LAN channel. The Gateway IP Address is the logical or Internet address of the router. The Gateway IP Address is entered as a dotted decimal IP address, such as 10.0.0.254. This option is available only if Static IP is selected.
LAN Channel Configuration Screen 2 - Server Management and Serial Over LAN Setup This screen allows you to continue to enter the necessary settings to configure the specified LAN channel. When this screen is displayed, the settings shown are the current settings for this LAN channel on the server. The continue button is enabled at all times on this screen. • Enable LAN Access: Enable LAN Access allows you to enable or disable the LAN access for the server.
LAN Channel Configuration Screen 3 - LAN Alerting Setup This screen allows you to continue to enter the necessary settings to configure the specified LAN channel. 48 • Enable LAN Alerting: Allows you to configure the LAN alert settings for this LAN channel on the server. The availability of all settings on this display depends on the setting of this checkbox. • Alert Destination Console 1 IP Address: Allows you to enter the first alert destination IP address for this LAN channel.
The next screen displayed allows you to select the type of alert to receive: • Select All Button: This button will select all of the filter checkboxes on the dialog. • Clear All: This button will clear all of the filter checkboxes on the dialog. Configuring the Serial/Modem Channel The Serial/Modem channel option is available on both the Management Module - Professional Edition and Management Module - Advanced Edition system configurations.
Serial/Modem Configuration Screen 2 - Configuring Remote Server Management Options for a Serial / Modem Connection This screen allows you to continue to enter the necessary settings to configure the serial/modem channel. • Enable Access: The Enable Access checkbox allows you to enable or disable Serial/Modem connectivity. When checked, all of the Serial/Modem parameters are enabled and you can set them to the appropriate values. When not checked, all of the Serial/Modem parameters on this page are disabled.
Serial/Modem Configuration Screen 3 - Configuring Alerting over a Serial/Modem Connection This screen allows you to continue to enter the necessary settings to configure the serial/modem channel. The Continue button is disabled/grayed out until all edit boxes on the screen have data entered. • Enable Serial/Modem Paging Checkbox: The Enable Serial/Modem Paging checkbox allows you to enable Serial/Modem paging.
Select Users to Configure Screen The Configure Users Screen provides a mechanism for configuring user access to LAN and Serial/ Modem channels. A maximum of four users are supported by the PLATINUM 7200 IR Server. The screens allow configuration of user settings like username, password and the per-channel configuration for each user. These options are available on both the Management Module - Professional Edition and the Management Module - Advanced Edition system configurations.
• Enable HTTPS for this User: The Enable HTTPS for this User checkbox is provided to Enable HTTPS feature for this user on the Advanced MM LAN Channel. This option is available only on the platform configuration that uses the Management Module - Advanced Edition. • Enable Telnet for this User: The Enable Telnet for this User checkbox is provided to Enable Telnet feature for this user on the Advanced MM LAN Channel.
Configuring the Advanced Features Advanced Features are configured through three main screens and several sub-screens. Each screen displays the configuration options for one or more of the advanced features. The Advanced Features are available only on the platform configuration that uses the Management Module - Advanced Edition.
Advanced Features Configuration Screen 2: HTTP Settings This screen allows you to continue the configuration of the Advanced Features on this server, by configuring the HTTP and HTTPS settings. The HTTP module accepts requests via HTTP on a user-configurable port (default port is 80). Two interface styles are supported via the network interface: • Browser Interface: The “browser interface” style presents web pages to the user, who may click buttons or enter text values in order to interact with the server.
Saving the Configuration to a Disk When you have completed the data entry portion of the SCW, you are prompted to save the configuration to a CD-ROM drive or to a USB flash memory device. This allows future servers to be configured identically to this server, using the silent mode of the SCW. Save Server Configuration to Disk: The Save Server Configuration checkbox saves the configuration to a USB accessable device. This makes configuring a group of identical servers fast and easy.
5 User Serviceable Platform Components Tools and Supplies Needed • Phillips #2 screwdriver • Flat head screwdriver • Antistatic wrist strap (recommended) Removing and Installing the Top Cover WARNING Make sure the rack is anchored securely so it will not tilt forward when the server chassis is extended. A crush hazard exists should the rack tilt forward. This could cause serious injury. CAUTIONS For proper cooling and airflow, do not operate the server with the cover removed.
Removing the Top Cover To remove the top cover, follow these instructions: 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. If the chassis is rack-mounted, slide the chassis out far enough to expose the entire top cover. 3. Unscrew the two captive screws on the faceplate of the chassis. 4. Slide the top cover toward the back of the chassis until the tabs on the cover disengage with the slots in the chassis. 5. Lift the cover to remove it. B A Figure 10.
Hot-swapping a System Fan Assembly Two cooling fan assemblies are located at the front of the chassis. Each assembly contains two fans. You cannot replace the individual fans within the assembly, but you can replace each fan assembly. You can replace a failed cooling fan assembly without turning off the power to the server only if the remaining fan in the assembly is fully operational. Each fan assembly uses an amber LED to indicate a failed fan condition.
Hot-swapping Hard Disk Drives The server supports five hot-swap drive carriers. Each carrier holds a standard one-inch high SCSI-2 or SCSI-3 hard drive. The procedures in this section describe how to determine drive status, remove a faulty drive, and install a new drive. If a drive is in a redundant configuration, you can install or replace a hot-swap hard disk drive without powering down the server.
Removing a Hard Disk Drive 1. Observe the safety, ESD, and other precautions described in “Safety Information.” 2. Press on the green drive carrier latch. 3. Pull the handle to remove the drive cage from the chassis. 4. Place the drive cage on a clean, static-free work surface. Mounting a Hard Disk Drive in a Carrier To mount a hard drive in a carrier: 1. Observe the safety, ESD, and other precautions described in “Safety Information.” 2.
Hot-swapping Power Supplies If your server is configured with two power supplies, you can replace a failed or failing power supply without powering down the server. CAUTION Because of chassis airflow disruption, a power supply bay should never be vacant for more than two minutes when the server power is on. Exceeding five-minutes might cause the system to exceed the maximum acceptable temperature and possibly damage system components.
Installing and Removing PCI Cards This section outlines the procedures for performing a hot-plug operation with PCI cards and installing and removing non-hot-plug PCI cards. Cards can be hot-swapped in PCI slots 1 through 5. The server must be powered down to install or remove a card from PCI slots 6 and 7. CAUTION Expansion slot covers must be installed on all vacant slots to maintain the electromagnetic emission characteristics of the server and to ensure proper cooling of the system.
Removing Hot-plug PCI Card with Hardware Hot-Plug Interface CAUTION Only PCI add-in cards in PCI slots 1 through 5 are hot-swappable. If you are adding or removing a PCI card from PCI slot 6 or 7, see “Removing a Non-Hot-Plug PCI Card” and “Installing a Non-Hot-Plug PCI Card”. 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. Remove the top cover. For instructions, see “Removing the Top Cover”. 3. Press the attention button for the slot.
Installing a Hot-plug PCI Add-in Card CAUTION Only PCI add-in cards in PCI slots 1 through 5 are hot-swappable. If you are adding or removing a PCI card from PCI slot 6 or 7, see “Removing a Non-Hot-Plug PCI Card” and “Installing a Non-Hot-Plug PCI Card”. 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. If your server is operating, use your operating system or GUI application to power down the PCI slot. 3. Remove the top cover.
Removing a Non-Hot-Plug PCI Card PCI cards installed in slots 1 through 5 are hot-swappable. If you are adding or removing a card from one of these slots, you can do so without powering down the server. If you wish to do so, follow the instructions under “Removing Hot-plug PCI Card with Operating System Hot-Plug Interface” or “Removing Hot-plug PCI Card with Hardware Hot-Plug Interface”, and “Installing a Hot-plug PCI Add-in Card”.
Installing and Removing the Fibre Channel Module Removing the Fibre Channel Module 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. Turn off all peripheral devices connected to the system. 3. Power down the system and unplug both AC power cords. 4. Remove the top cover. For instructions, see “Removing the Top Cover”. 5. Disconnect any cables attached to the Fibre Channel Module. 6. Remove the Memory Board or Memory Board air baffle from Slot C.
Installing the Fibre Channel Module 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. Turn off all peripheral devices connected to the system. 3. Power down the system and unplug both AC power cords. 4. Remove the top cover. For instructions, see “Removing the Top Cover”. 5. Remove the Memory Board or Memory Board air baffle from Slot C. For instructions, see “Cold Removal of Memory Board”. 6.
CAUTION Do not attempt to hot remove or hot add a Memory Board in a non-redundant configuration. If your server is not configured in the BIOS setup utility for Maximum Compatibility, Memory RAID, or Memory Mirroring, you must power down your server before removing or installing any Memory Board or memory DIMMs. For instructions, see “Cold Removal of Memory Board” and “Cold Insertion of a Memory Board”.
Hot Removal of a Memory Board NOTE If you remove a Memory Board from your server, you must either replace it with a replacement Memory Board or you must install a Memory Board air baffle. If the Memory Board is installed in a system that is powered on, the following steps are required to ensure proper hot removal so that the system will not crash: 1. Observe the safety precautions, warnings, and cautions described in “Safety Information”. 2. Remove the top cover.
Hot Insertion of a Memory Board 1. Add or replace memory DIMMs as needed. For instructions, see “Installing and Removing DIMMs”. 2. Ensure the handle on the Memory Board is in the open / up position. 3. Align the ends in the card guides and slide the Memory Board into the Memory Board slot. 4. Push the handle down into the fully-locked position. 5. Install the top cover. For instructions, see “Installing the Top Cover”.
Installing and Removing DIMMs To remove or install the DIMMs, remove the Memory Board from the chassis and install the DIMMs on the Memory Board, then reinstall the Memory Board. Be sure to follow the “Rules for Adding Memory”. CAUTION Do not attempt to hot remove or hot add a Memory Board in a non-redundant configuration.
Installing DIMMs CAUTIONS Use extreme care when installing a DIMM. Applying too much pressure can damage the connector. DIMMs are keyed and can be inserted in only one way. Hold DIMMs only by the edges. Do not touch the components or gold edge connectors. Install DIMMs with gold-plated edge connectors only. The maximum DIMM height is 4.445 cm (1.75 inches). Do not install DIMMs that exceed this height. NOTE DIMM slots on the memory module must be installed only in certain configurations.
Removing DIMMs CAUTION Use extreme care when removing DIMMs. Too much pressure can damage the connector. Apply only enough pressure on the plastic levers to release the DIMM. 1. Remove the top cover. For instructions, see “Removing the Top Cover”. 2. Remove the Memory Board. For instructions, see “Hot Removal of a Memory Board” or “Cold Removal of Memory Board”, depending on your server configuration. 3. Remove the Memory Board DIMM cover from the Memory Board: - Pull out on the latch.
6 Replacing the CMOS Battery The lithium battery on the Main Board powers the real-time clock (RTC) for three to four years in the absence of power. When the battery weakens, it loses voltage and the system settings stored in CMOS RAM and the Real Time Clock (such as the date and time) can be wrong. Contact your customer service representative or dealer for a list of approved replacement batteries.
CAUTION Do not attempt to pull the battery up until it is pushed clear of the smaller prongs. Doing so may damage the battery holder on the Main Board. B A Figure 13. Removing the Battery 9. Dispose of the battery according to local ordinance. 10. Remove the new lithium battery from its package. 11. Being careful to observe the correct polarity, insert the battery at an angle into the battery socket with the edge of the battery under the larger prongs in the battery socket. 12.
7 Regulatory and Integration Information Product Regulatory Compliance Product Safety Compliance The server board complies with the following safety requirements: • EN 60950 (European Union) • IEC 60950 (International) • CE - Low Voltage Directive (73/23/EEC) (European Union) Product EMC Compliance The server board has been has been tested and verified to comply with the following electromagnetic compatibility (EMC) regulations when installed a compatible host system.
