MAXDATA PLATINUM 100 I M7 User’s Manual
Contents
Contents 1 Setting up the System 5 Safety Information ...................................................................................................................................5 Server Position ...................................................................................................................................5 System Access Warnings ..................................................................................................................6 Powering up the System ............
Figures 1. 2. 3. 4. 5. 6. 7. PLATINUM 100 I Controls .................................................................................................................7 Board Connector and Component Locations ..................................................................................10 Configuration Jumpers ....................................................................................................................11 Back panel Connectors .......................................................
1 Setting up the System Safety Information Server Position Please take note of the following criteria for creating a practical and safe workplace when setting up your computer: ! CAUTION The system can be used anywhere the temperature is suitable for people. However, rooms with humidity over 70%, and dusty or dirty areas are not appropriate. In addition, do not expose the server to any temperatures over +30°C or under +10°C.
System Access Warnings ! CAUTION To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product: • Turn off all peripheral devices connected to this product. • Turn off the system by pressing the power button to off. • Disconnect the AC power by unplugging all AC power cords from the system or wall outlet. • Disconnect all cables and telecommunication lines that are connected to the system.
Powering up the System At the front of the case, you can find the necessary controls like power button and the HDD LEDs. Press the power button one time briefly in order to boot the server. Figure 1. PLATINUM 100 I Controls MAXDATA PLATINUM 100 I M7 A. Power switch B. Power LED C. HDD LED D.
2 Board Features This chapter briefly describes the main features of the mainboard. Table 1 summarizes the major features of the board. Table 1.
Connector and Header Locations Figure 2 shows the approximate location of the major components on board. A B C D E FG H I J K L M LL KK JJ II HH GG FF EE DD CC AA Y BB Z X W VU T SR Q P O N Figure 2. Board Connector and Component Locations Table 2. Board Connectors and Components Label Description 10 Label Description A. Video Memory T. Battery B. PCI 32/33 Slot 2 U. 2x12 Main Power Connector C. ATI ES1000 Video Controller V. Front System Fan D. PCIe x8 (x4 Lane) Slot 5 W.
Configuration Jumpers Figure 3 shows the location of the configuration jumpers. CMOS CLR J1G3 BIOS 2 3 Default CLEAR CMOS 3 2 J1H3 Default Remove jumper for BIOS recovery Figure 3. Configuration Jumpers Table 3. Configuration Jumpers Jumper Name What happens at system reset... CMOS Clear If pins 2-3 are jumpered, the CMOS settings will be cleared on the next reset. These pins should be jumpered on 1-2 for normal operation. BIOS Recovery Remove the jumper for BIOS recovery.
Back Panel Connectors D B A C E Figure 4. Back panel Connectors Table 4. Back panel Connectors Label Description Label Description A. Stacked PS2 Mouse/Keyboard Ports D. NIC (10/100/1000 Mbps) B. Serial A E. USB1-2 C. Video The NIC LEDs at the right and left of the NIC provide the following information: Table 5.
Hardware Requirements To avoid integration difficulties and possible board damage, your system must meet the requirements outlined below. Memory The Intel® Server Board S3000AH provides four DIMM sockets across two banks. Bank 1 consists of DIMM sockets 1A and 1B. Bank 2 consists of DIMM sockets 2A and 2B. Minimum memory operation is a single 256MB DIMM in socket 1A. This will provide single-channel interleave. For dual-channel interleave, two identical DIMMs are required in sockets 1A and 1B.
3 Hardware Installations and Upgrades Before You Begin Before working with your server product, pay close attention to the “Safety Information” at the beginning of this manual. Tools and Supplies Needed • Phillips (cross head) screwdriver (#1 bit and #2 bit) • Needle nosed pliers • Antistatic wrist strap and conductive foam pad (recommended) Installing and Removing Memory The silkscreen on the board for the DIMMs displays DIMM 1A, DIMM 1B, DIMM 2A, DIMM 2B starting from the center of the board.
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (see letter “A” in Figure 5). 7. Holding the DIMM by the edges, remove it from its anti-static package. 8. Position the DIMM above the socket. Align the notch on the bottom edge of the DIMM with the key in the DIMM socket (see letter “B” in Figure 5). 9. Insert the bottom edge of the DIMM into the socket (see letter “C” in Figure 5). 10.
Replacing the Backup Battery The lithium battery on the server board powers the RTC for up to 10 years in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your customer service representative or dealer for a list of approved devices. ! WARNING Danger of explosion if battery is incorrectly replaced.
To replace the battery, follow these steps: 1. Observe the safety and ESD precautions in “Safety Information”. 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord from the server. 4. Remove the server‘s cover and locate the battery. 5. Lift the battery retention mechanism (see Figure 6). 6. Remove the battery from its socket. Figure 6. Removing the Battery 7. Dispose of the battery according to local ordinance. 8.
4 Server Utilities Using the BIOS Setup Utility This section describes the BIOS Setup Utility options, which is used to change server configuration defaults. You can run BIOS Setup with or without an operating system being present.
Table 6 describes the keyboard commands you can use in the BIOS Setup menus. Table 6. Keyboard Commands Press Description Help - Pressing F1 on any menu invokes the general Help window. ←→ The left and right arrow keys are used to move between the major menu pages. The keys have no affect if a sub menu or pick list is displayed. ↑ Select Item up - The up arrow is used to select the previous value in a menu item’s option list, or a value field pick list.
Clearing the CMOS If you are not able to access the BIOS setup screens, the CMOS Clear jumper will need to be used to reset the configuration RAM. 1. Power down the system and disconnect the AC power. 2. Open the server. 3. Move the jumper from the normal operation position, at pins 1 and 2 to the CMOS Clear position, covering pins 2 and 3 as indicated in the following diagram. CMOS CMOS CLR CLR J1G3 2 3 Default Default CLEAR CLEAR CMOS CMOS Figure 7. Clearing the CMOS 4.
Configuring the System for embedded Serial ATA RAID Configuring the BIOS 1. Make sure you are having at least two SATA hard drives. 2. Enter system BIOS Setup by pressing the key after the Power-On-Self-Test (POST) memory tests begin. 3. Go to “Advanced” - “Drive Configuration”; ensure “Configure SATA as RAID” is enabled. 4. Then save your settings by pressing . Creating your RAID set 1.
5 Regulatory and Compliance Information Product Regulatory Compliance Product Safety Compliance The server complies with the following safety requirements: • EN 60950 (European Union) • CE – Low Voltage Directive (73/23/EEC) (European Union) Product RoHS Compliance Restriction of Hazardous Substances: This server system is compliant to European Directive 2002/95/ EC (RoHS).
