V11.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VIII • Only use a power adapter approved for use with this computer.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XVI
Preface Contents Notice .................................................................................I FCC Statement ................................................................ III FCC RF Radiation Exposure Statement: ........................ IV EuP Off Mode Power Consumption Statement: .............. V Instructions for Care and Operation ............................... VI Power Safety ................................................................ VIII Polymer Battery Precautions ...............
Preface Gestures and Device Settings ........................................2-8 Audio Features .............................................................2-12 Optimizing Audio Recording ......................................2-13 Adding a Printer ...........................................................2-14 USB Printer ..................................................................2-14 Parallel Printer .............................................................2-14 Power Management Overview ......
Preface Optional Drivers ............................................................4-9 PC Camera Module ........................................................4-9 Wireless LAN Module ...................................................4-9 Fingerprint Reader Module ............................................4-9 3.75G/HSPA Module .....................................................4-9 TPM Driver ....................................................................4-9 IRST Driver ...........................
Preface Upgrading the System Memory (RAM) ........................6-8 Modules & Options Overview ........................................................................7-1 PC Camera Module ........................................................7-2 PC Camera Driver Installation .......................................7-3 Wireless LAN Module .................................................7-10 3rd Party WLAN Driver Installation ...........................7-11 Intel® WLAN Driver Installation ...............
Preface Bluetooth Connection Problems ..................................8-13 Intel® Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules .........................8-17 Interface (Ports & Jacks) Overview ....................................................................... A-1 Intel Video Driver Controls Intel Video Driver Installation ...................................... B-1 Dynamic Video Memory Technology ...................... B-1 Intel® Graphics & Media Control Panel ......................
Preface XXII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, Card Reader, ExpressCard/34/54), Touchpad & Mouse, Audio & Printer. • Chapter 3 The computer’s power saving options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide Model Differences This notebook series includes two different model types that vary slightly in design style, color and general appearance. Note that your model may appear slightly different from those pictured in this manual. See “Specifications” on page C - 1 for a full information on the chipsets, CPUs and modules supported by each model. System Software Your computer may already come with system software pre-installed.
1 Quick Start Guide Figure 1 - 2 LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. Built-In PC Camera LCD Speakers Power Button Hot Key Buttons Keyboard Built-In Microphone Touchpad & Buttons Fingerprint Module System Map: LCD Panel Open 1 Wireless Device Operation Aboard Aircraft 2 5 3 3 4 6 7 9 Note that the valid operational area for the Touchpad’s scroll bar and Buttons is that indicated within the red dotted lines above.
Quick Start Guide LED Indicators The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/ hot-keys unique to the system’s regular keyboard may not work. NumLk & ScrLk Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.
Quick Start Guide Keyboard The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 3, on page 1 - 10 for full function key combination details. NumLk & ScrLk Keys Function Keys Play/Pause Key Fn Key 3.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Keys Function Keys Function Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle Fn + Fn + F1 3.
Quick Start Guide System Map: Front & Left Views Figure 1 - 4 Front & Left Views 1. 2. 3. 1 2 3 4 5 8 6 8 7 10 9 Multi-In-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo LED Indicators DC-In Jack External Monitor Port 4. RJ-45 LAN Jack 5. e-SATA Port/USB 2.0 Combo Port 6. HDMI-Out Port 7. Vent/Fan Intake/ Outlet 8. 2 * USB 3.0 Ports 9.
1 Quick Start Guide Figure 1 - 5 Right & Rear Views 1. 2. 3. 4. 5. 6. 7. S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack 1 * Powered USB 2.0 Port Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3) Security Lock Slot Battery System Map: Right & Rear Views 1 2 3 4 5 6 7 Powered USB 2.0 Port The powered USB 2.
Quick Start Guide CD/DVD Emergency Eject Changing DVD Regional Codes If you need to manually eject a CD/ DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.
1 Quick Start Guide Figure 1 - 6 Bottom View 1. 2. 3. 4. 5. Battery Docking Port RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Note: the 3.75G/HSPA USIM Card is located under the RAM & CPU Bay Cover. System Map: Bottom View 1 Battery Information 2 Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Quick Start Guide 3.75G/HSPA Module USIM Card Installation If you have included an optional 3.75G/HSPA module in your purchase option, follow the instructions below to install the USIM card (which will be provided by your service provider), and then run the Mobile Partner application. See “Wireless Manager” on page 7 - 51 for instructions on installing the program etc. 1. 2.
1 Quick Start Guide Docking Port Follow the instructions below before connecting the computer to the docking station, if included in your purchase configuration (Factory Option for Model A computers). Failure to open the cover of the docking port before connecting the computer to the docking station may result in irreparable damage to the connector on the docking station. 1. 2. 3. Turn the computer over. Slide the docking port cover latch in the direction of the arrow at point 1 to open the cover.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For more detailed video information see“Intel Video Driver Controls” on page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearance and Personalization category. Click Adjust Screen Resolution/Adjust resolution. OR 4. 5. 6.
Quick Start Guide To access the Intel(R) Graphics and Media Control Panel: 1. 2. Click Advanced settings 2 (Figure 1 - 10 on page 1 - 18) in the Display Settings control panel in Windows. Click Graphics Properties (button) 3 (Figure 1 - 11) in the Intel Graphics & Media Control Panel tab. OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon 4 (Figure 1 - 11) in the taskbar and select Graphics Properties from the menu. OR 5.
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 14) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-in-1 Card Reader ExpressCard Slot Touchpad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 18).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 13. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Touchpad Scrolling This computer model series may feature different Touchpad versions. These Touchpads may differ in their vertical scrolling function in most scrollable windows. Touchpad and Buttons/Mouse The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Features & Components Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings.
Features & Components 2 Figure 2 - 7 Scrolling Gesture Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight continuous motion). Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu).
Features & Components Optimizing Audio Recording 2 Follow these instructions to optimize your audio recording. 1. 2. 3. 4. Double-click the taskbar icon to bring up the Realtek HD Audio Manager. Click the Microphone tab. Click the Noise Suppression button to prevent any background noise or feedback. Click OK to close the Realtek HD Audio Manager.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Silent Mode Use the key to toggle Silent Mode to reduce fan noise and save power consumption. Note this may reduce computer performance. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Taskbar Icon If the taskbar icon does not appear then click the taskbar arrow and select Customize. Energy Star Power Saving This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these instructions: 1. 2. Right-click the taskbar icon (see sidebar). Select Power Conservation Modes.
Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 2 on page 3 - 5).
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button). 4 Figure 4 - 1 - Drivers Installer Screens 1. 2. 3. Check the driver installation order from Table , on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu. Click to select the driver you wish to install, (you should note down the drivers as you install them).
Drivers & Utilities Driver for Windows 7 with Service Page Driver for Windows 7 with Service Page Chipset Page 4 - 5 PC Camera Module Page 7 - 2 Video Page 4 - 5 Wireless LAN Module Page 7 - 10 LAN Page 4 - 6 Fingerprint Reader Module Page 7 - 29 CardReader Page 4 - 6 Bluetooth Module Page 7 - 34 TouchPad Page 4 - 6 3.75G/HSPA Module Page 7 - 48 Modem (Optional) Page 4 - 6 Trusted Platform Module Page 7 - 73 Hot Key Page 4 - 7 IRST Driver Page 7 - 87 USB 3.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Drivers & Utilities 4 LAN 1. Click 3.Install LAN Driver > Yes. 2. Click Install Drivers and Software > Next. 3. Click the button to accept the license and click Next. 4. Click Next > Install. 5. Click Finish. 6. The network settings can now be configured. CardReader 1. Click 4.Install Cardreader Driver > Yes. 2. Click Install. 3. Click Finish. TouchPad 1. Click 5.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4.
Drivers & Utilities Hot Key 1. Click 7.Install Hotkey AP Driver > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. USB 3.0 1. Click 8.Install USB 3.0 Driver > Yes. 2. Click Next. 3. Click the button to accept the license agreement and click Next. 4. Click Install. 5. Click Finish. 6. Click Finish. OR 7. Choose the language you prefer and click OK. 8. Click Next. 9. Click the button to accept the license agreement and click Next. 10. Click Finish. MEI 1. Click 9.
Drivers & Utilities Windows Experience Index 4 After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in): 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click “Rate this computer”. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel.
Drivers & Utilities Optional Drivers PC Camera Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. See “PC Camera Module” on page 7 - 2. Wireless LAN Module See “Wireless LAN Module” on page 7 - 10. Fingerprint Reader Module See “Fingerprint Reader Module” on page 7 - 29. Bluetooth Module See “Bluetooth Module” on page 7 - 34. 3.75G/HSPA Module See “PC Camera Module” on page 7 - 2.
Drivers & Utilities 4 4 - 10
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . The Setup Utility Each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Intel® vPro™ technology Intel® vPro™ technology is supported by Model A computers only. This set of technology features, built into the computer’s motherboard, allows Information Technology departments remote access to the computer. This allows the IT department to monitor, maintain and manage computers regardless of the state of the operating system or the computer’s power state.
BIOS Utilities Figure 5 - 2 5 Intel(R) Management Engine (Password Creation) Once you have entered the password you will then be taken to the platform configuration screen.
BIOS Utilities Figure 5 - 3 Intel(R) Management Engine (Platform Configuration) The platform configuration screen allows you to setup Intel ME as per your requirements (consult your IT administrator for the actual settings required). See “MEI” on page 4 - 7 and “Intel® Management and Security Status” on page 7 - 88.
BIOS Utilities Main Menu Figure 5 - 4 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 5 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting.
BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. 5 Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 6 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Password Warning If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. 5 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 14 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility.
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the TPM Support menu and select Enable to display the full TPM configuration menu (see “Trusted Platform Module” on page 7 - 96 for details).
BIOS Utilities TPM State (Security Menu > TPM Support Enabled) Select TPM State, press Enter and select Enable to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. 5 Figure 5 - 8 TPM State (Enabled) As the computer restarts press F2 to enter the BIOS again and go to the TPM Configuration menu.
BIOS Utilities Pending TPM operation (Security Menu > TPM Support & TPM State Enabled) Select Pending TPM operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer.
BIOS Utilities Boot Menu Figure 5 - 10 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 18 Boot Menu When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Sequence (Boot Menu) Use the arrow keys to move up and down the menu and use the F5 and F6 keys to move the device’s boot priority up and down the list (the selected device will be highlighted in white).
BIOS Utilities Exit Menu Figure 5 - 11 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. Grip the tab and slide the hard disk in the direction of arrow 4 Lift the hard disk out of the bay 5 . . 4 Figure 6 - 3 HDD Assembly Removal 5 6. 7. 6 Remove the screw(s) 6 and the adhesive cover 7 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and loosen screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer 4. 5. Remove the screw at point 4 , and use a screwdriver to carefully push out the optical device at point 5 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDRIII (DDR3) type memory modules (see “Memory” on page C - 2 for details of supported module types). 1. 2. 6 Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 .
Upgrading The Computer 3. 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 4 , and remove the cover 5 . Fan Cable & Cover Make sure you reconnect the fan cable 4 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in “Cover Pins” on page 6 - 11. 5 6 4 5.
Upgrading The Computer 6. 7. 8. The RAM module will 8 pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. Figure 6 - 10 RAM Module Removal 8 6 Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket.
Upgrading The Computer 11. Replace the bay cover and screws (make sure you reconnect the fan cable before screwing down the bay cover). Cover Pins Note that there are cover pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover (see Figure 6 - 11). Figure 6 - 11 Cover Pin Alignment 12. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
Upgrading The Computer 6 6 - 12
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • • • • • PC Camera Module Wireless LAN Module Security Modules (Fingerprint & TPM) Fingerprint Reader Module Bluetooth Module 3.75G/HSPA Module Trusted Platform Module IRST Driver Intel® Management and Security Status Important Notice 3.
Modules & Options Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. PC Camera Module Make sure that the PC Camera module is on before installing the driver and use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 10) to toggle power to the PC Camera module.
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Webcam Driver > Yes. 4. Click Next > Finish to restart the computer. OR 5. Click Next >Install > Finish > Finish to restart the computer. 6.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 1 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 5
Modules & Options Pre-Allocating File Size/Space Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. You may pre-allocate the file size (File > Allocate File Size/Space) for the capture file in the camera program (you may need to set a folder location first).
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here, including the figures pictured here. Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3.
Modules & Options Taking Still Pictures The camera application allows you to take still pictures. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop. Snapshot Folder on the The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 10/ Table 1 - 1, on page 1 - 7).
Modules & Options 3rd Party WLAN Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next. 6. Click Finish to restart the computer.
Modules & Options Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options Security Enabled Networks 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Intel® My WiFi Configuration Intel® My WiFi Technology uses your WLAN (for Intel WLAN modules only) module to allow you to connect up to eight other WiFi enabled devices (e.g. digital cameras, other computers, cell phones, handheld devices etc.) to your computer (similar to Bluetooth), while still connecting to the Internet through your WiFi wireless connection.
Modules & Options Intel® My WiFi Configuration You can configure the My WiFi settings as follows. 1. 2. 7 Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . Click Enable (on the first run of the program there will be no connected devices listed).
Modules & Options 3. 4. 5. Click Start and click Control Panel. Click Network and Sharing Center (Network and Internet). Click Change adapter settings.
Modules & Options 6. Right-click Wireless Network Connection and select Properties. Figure 7 - 8 Network Connections Right-click Wireless Network Connection and select Properties.
Modules & Options 7. 8. 9. Click Sharing (tab) and select “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Connection under Home networking connection. Click OK. Click “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Connection.
Modules & Options 10. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . 11. Click Profiles .
Modules & Options 12. Click Profiles, click Intel Wireless PAN and click Edit or New (Note that all preset settings may not be editable - see sidebar). Figure 7 - 11 Profiles Profile Settings 13. You can change the Profile Name and Network Name to your personal preferences in General (tab). Profile and Network Names The Profile Name is the name as displayed on your computer in the Network Connections control panel (see Figure 7 - 13 on page 7 - 22).
Modules & Options 14. Click Security (tab). 15. Change the Security Type to WEP and the Encryption Type to 64bit. 16. Enter a password (8 characters long) in the Password box.
Modules & Options 17. Click Sharing (tab). 18. It is recommended that the Filter Network Traffic and DHCP and DNS Server are Disabled.
Modules & Options 19. Click Advanced (tab). 20. It is recommended that the Default Channel is set to Channel 1, 6 or 11. 21. Click OK to save the settings.
Modules & Options 22. Double-click Wireless Network Connection in Network Connections. 23. Click Details to display the Network Connection Details.
Modules & Options 24. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . 25. To add a new device follow the instructions in the devices’ user guide for connecting to a WiFi network. 26. Click Add New Device in Intel® My WiFi Utility to confirm the security settings detail.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Modules & Options Fingerprint Reader Module The fingerprint reader module provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 3.Install Fingerprint Driver > Yes. 4. Click Next > Next > Next. 5.
Modules & Options Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. User Enrollment 1. 2. 3. 4. 5. 7 Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the notification area icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules & Options 6. Click the button above any of the fingers to begin the enrollment process for that finger. 7. Swipe the finger until the progress bar reaches 100% to enroll that finger. 8. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Save and Continue. 9. Enter a backup password and click Apply. 10. Close the fingerprint status window. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc.
Modules & Options 11. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 12. Click “Help” in Control Center Home to get more information on any topic. 13. You can also run the Tutorial, or Product Tour video to get more information.
Modules & Options Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Modules & Options Wireless Device Operation Aboard Aircraft 7 Bluetooth Module If your purchase option includes the Combination Wireless LAN & V3.0 Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Modules & Options Intel Bluetooth Combo Driver Installation Note this driver is required only for the Intel combo Bluetooth and WLAN module only. 1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3.
Modules & Options Standard Bluetooth Configuration in Windows 7 Add a Device Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices. 7 Bluetooth Module & Resuming From Sleep Mode Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation).
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code. Figure 7 - 23 3.
Modules & Options 4. Figure 7 - 24 Pairing Codes Pairing Code Example 7 Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3.
Modules & Options 3rd Party Bluetooth Combo Driver Installation High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & V3.0 Bluetooth module supports high speed (V3.0) data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed (V3.0) data transfer make sure that both the WLAN and Bluetooth modules are powered on.
Modules & Options 3rd Party Bluetooth & WLAN Combo Settings This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (menu heading). Bluetooth Module & Resuming From Sleep Mode The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state.
Modules & Options 4. 5. 7 Figure 7 - 28 General Settings 7 - 42 Bluetooth Module Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings.
Modules & Options 6. 7. Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings.
Modules & Options Bluetooth Networking Setup This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 27 on page 7 - 41). 7 Figure 7 - 30 Network Settings 4. 5. 6. 7 - 44 Bluetooth Module Click Network Settings (make sure the Bluetooth module is powered on.
Modules & Options Bluetooth & WLAN Combo Module Configuration Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Bluetooth Module & Resuming From Sleep Mode To Turn the Bluetooth Module On 1. Press the Fn + F12 key combination to power on the Bluetooth module. To Add a Bluetooth Device 1. 2.
Modules & Options 3. You will then be presented with a menu of options to select from. 4. Click the appropriate button to connect to the device.
Modules & Options 5. 6. You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
Modules & Options 3.75G/HSPA Module If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page C - 4 for specification details) in your purchase option, you will have the appropriate application provided for your particular module. Follow the instructions on page 7 - 50 to install the USIM card (supplied by your service provider), and then install the application (see over for further details). Important Notice - 3.
Modules & Options Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot Key Indicators” on page 1 - 10) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the on-screen indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table , on page 4 - 3.
Modules & Options Power Safety Warning Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). 3.75G/HSPA Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5. Turn off the computer, and turn it over. Slide the latch 1 in the direction of the arrow.
Modules & Options Wireless Manager With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Wireless Manager application. The Wireless Manager application allows you to directly access your HSPA internet service from the computer. Wireless Manager Installation 1. Enable power to the module by pressing the Fn + key combination (give the module about 10 seconds to power on - the on screen icon will indicate the module’s power status). 2.
Modules & Options PIN Number The PIN number for your USIM card will be supplied by your service provider. You usually have a limited number of attempts to enter the correct PIN number. 7 Wireless Manager Application The connection information is stored on the USIM card supplied by the service provider (where this is not the case you may need to create a profile - see “Creating a Profile” on page 7 - 58). 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination.
Modules & Options 5. 6. 7. The system will connect to your network. Connected will appear above the timer icon (the timer will indicate your connected time for the current session) . You can then access the internet, download e-mail etc. as per any internet connection. Wireless Manager Help To get help on Wireless Manager configuration and settings, click the Help icon or press F1. 7 Figure 7 - 36 Wireless Manager (Connected) 3.
Modules & Options 8. Click the Wireless Manager notification area icon to view the connection status, or wireless icon to view the Mobile Broadband Connection status. 9. The indicator will display the signal strength and radio access technology.
Modules & Options Profiles 1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click the Settings > Advanced. Click the Profiles (tab). Figure 7 - 38 Advanced Settings Profiles 7 3.
Modules & Options 4. Multiple profiles may be available from the USIM card and the first time the application starts it may require you to select a profile (Set Profile) to use for your connection. Figure 7 - 39 Multiple Profiles Found 7 Automatic Profile Selection If Automatic selection is chosen, then the application will search the operator profile database for a profile that matches the details on your USIM card. If a correct profile is found it will be automatically selected as your profile.
Modules & Options Selecting a Profile 1. 2. 3. Click Manual selection (button). Click the Filter to view the drop-down list. Select the Profile you wish to use and click Apply to confirm the selection. Figure 7 - 40 Profile - Manual Selection (Filter) 7 3.
Modules & Options Creating a Profile Deleting a Profile To delete a profile click to select Manual selection and select the profile and click Delete. Modifying a Profile 7 1. 2. 3. 4. 5. 6. 7. 8. Click Manual selection (button). Click the New. Enter a name you prefer for the profile. Enter the Access Point Name (APN). Enter the User Name and Password if required (some service providers may not require this information and the fields may then be left blank).
Modules & Options Settings The Settings tab allows you at adjust the application features. Click to put a tick in Launch Wireless Manager at Windows startup to launch the application at Windows Startup. Figure 7 - 42 Settings 7 The Advanced settings allows more detailed configuration. To access the Advanced settings: 1. 2. 3. Access the Wireless Manager program from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click the Settings > Advanced.
Modules & Options PIN Notes You will have to enter your current PIN to change the PIN settings. Request PIN at startup will apply only after you have shut the computer down and restarted it (not just restarted). 7 SIM Most USIM cards are protected by a Personal Identity Number (PIN). You may turn on or off the Request PIN at startup (click Apply to save any changes). You can also Change PIN (you will need to enter the new PIN in the two fields provided and click Apply to save any changes).
Modules & Options Networks The mobile network list lists available networks at your location, and allows you to select a network which to connect. You must disconnect before being able to select a network. Connection You can set the Wireless Manager to automatically connect at Windows startup (however the module must be powered on, and radio must be turned on). You can also automatically connect when resuming from a power-saving state (click Apply to save any changes).
Modules & Options Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using the Wireless Manager, if your service supports SMS. SMS Utility 1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start.
Modules & Options Messages Click the Messages tab to access the tabs displaying text messages. The tabs at the top of the menu display the Inbox, Drafts, Outbox, Sent and Trash menus. Inbox Drafts Outbox Sent Trash 7 Figure 7 - 46 SMS Utility Messages Text messages are automatically saved to your computer and may be sorted in ascending or descending order by name or date. 3.
Modules & Options Sending a Text Message 1. 2. 3. 4. 5. 6. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the New Message tab. Enter the phone number in the To field (multiple numbers may be entered to select a name from separated by a semicolon (;), or click the phonebook icon the phonebook.
Modules & Options 7. 8. 9. Click Send to send the message or Save to save the message in the Drafts folder. clears both the Message and To fields. Clicking the Clear icon If radio is on then the message will be sent, however if the radio is off the message will be stored in the Outbox. Note that you do not have to connect to the network to Send/Receive SMS messages. Inbox Any received text messages will be displayed in the Inbox.
Modules & Options Messages • Opening a text message: Double-click the message and the message will open in a new window (to close it click the close icon in the top right of the message). Figure 7 - 49 Click to close the message Close Message • Previewing a text message: Click the preview icon will open. Click the icon again to close the preview. 7 and the message preview • Replying to a text message: Double-click the message and click Reply.
Modules & Options Phonebook The Phonebook allows you to view and edit all your frequently used contacts, and is divided into Contacts and Groups . To access the Phonebook: 1. 2. 3. Access the Wireless Manager application from the Start menu (Start > All Programs > Wireless Manager > Wireless Manager) or the desktop shortcut . Click SMS and the SMS Utility will then start. Click the Phonebook tab. 7 Figure 7 - 50 SMS Utility Phonebook (Contacts) 3.
Modules & Options Import/Export Contacts Import/Export Contacts: Click the Import/ Export buttons to import or export the list of contacts. 7 Contacts • New Contact: Click the New contact button to create a contact. Add the name and at least one phone number (Mobile, Work, Home and Other fields are available) for the contact. Click the icon to expand the number details. Select Synchronize with SIM to synchronize the contact information with your USIM card. Click the Save icon to save the information.
Modules & Options Groups You can organize existing contacts into groups from the Groups tab. • New Group: Click the New group button to create a group. Click the icon to expand the group details, and click a check box to add at least one phone number from the contacts for the group. Click the Save icon to save the information.
Modules & Options SMS Settings The SMS Utility Settings tab allows you at adjust the SMS features. Figure 7 - 53 SMS Utility Settings SMS Settings 7 Message Length: You can set the number of blocks that can be sent (up to a length of 10 blocks). Message validity period: This sets the period after which the message will be deleted from the SMS center and therefore not forwarded to the recipient(s) when they come online.
Modules & Options Send Click Delivery Report to automatically request a reply from a recipient. If you click to Send messages in Outbox automatically upon connection then messages written when the radio is off, will then be sent automatically the next time radio is turned on. You can also choose to Include original message in reply. Notification This menu allows you to enable/disable Show animation on new message to get an animated notification of newly received messages.
Modules & Options Number You can choose to Use default service center number or you can uncheck the box and add your number manually if your service provider supplies a different number (click Apply to save the change or Default to return to the default number). Memory Phonebook memory status displays the number of contacts displayed on the USIM card. 7 Figure 7 - 55 SMS Utility Advanced Settings Number & Memory 7 - 72 3.
Modules & Options Trusted Platform Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu Select TPM Configuration and press Enter. Select TPM Support and press Enter, select Enable and press Enter. Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. 7.
Modules & Options 8. Select Pending TPM operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership) and press Enter. You will then need to press F4 to save the changes and restart the computer. Figure 7 - 57 Pending TPM operation (Enable Take Ownership) 7 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 76) and then initialize the TPM.
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver (if you do not do see the note below). 2. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 3. Click Option Drivers (button). 4. Click 6.Install TPM Driver > Yes. 5. Click Install > Next. 6. Click the button to accept the license and click Next. 7. Click Next > Next > Install. 8.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. Run the application from the Infineon Security Platform Solution > Manage Security Platform item in the Start > Programs menu. Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. Help 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 7 You can also click the Help button in any of the Infineon Security Platform Settings Tool tabs to bring up specific help topics on each tab.
Modules & Options Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Menus Note that not all the menus pictured here will be available for access.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Modules & Options IRST Driver Install the Intel Rapid Storage Technology to support your SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 11). 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 7.Install IRST Driver > Yes. 4. Click Next. 5. Click Yes > Next > Next. 6. Click Finish to restart the computer.
Modules & Options Intel® Management and Security Status (Model B Only) Access the Intel® Management and Security Status control panels from the Start menu in Windows. These features allow users and IT Administrators to enhance and protect computing assets. Your system administrator will need to assist you in managing some of the information here.
Modules & Options General The General tab provides basic information on Intel® AMT, Intel® Standard Manageability, Level 3 Manageability Upgrade, Intel® Anti-Theft and Intel® RPAT status and events.
Modules & Options Intel® Active Management Technology The Intel® AMT tab will be shown if you system is configured to support it. This allows your network’s IT professionals to remotely discover, heal and protect your computer.
Modules & Options Intel® Anti-Theft This tab displays information on Intel® Anti-Theft information. Click on the link to connect to an Intel site to get more information on Intel® Anti-Theft technology.
Modules & Options Advanced The Advanced tab provides additional information on the system.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 14). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination in order to enable the module (see “Function/Hot Key Indicators” on page 1 - 10). Run the BisonCap program to view the camera picture. The Wireless LAN/Bluetooth/ PC Camera/3.75G/HSPA modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting 8 Problem Possible Cause - Solution A yellow exclamation mark appears alongside PCI Simple Communications Controller (Other Devices) in Device Manager. The IRST driver will fix this known issue. Install the IRST driver (see “IRST Driver” on page 7 - 87). I cannot obtain high speed Bluetooth data transfer. To obtain high speed Bluetooth data transfer take into account the following: • Only the combination Wireless LAN & V3.0 Bluetooth module supports high speed (V3.0) data transfer.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. 8 Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Troubleshooting Intel® Centrino Advanced WLAN & Bluetooth V3.0+HS Combo Modules Note that, at the time of going to press, Intel® Centrino® Advanced-N 6230 or Intel® Wireless-N 1030 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see “Standard Bluetooth Configuration in Windows 7” on page 7 - 38). Do not use the Bluetooth & WLAN Combo settings information outlined from page 7 - 30 to page 7 - 36.
Troubleshooting 8 8 - 18
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
Interface (Ports & Jacks) A Item Description HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video signals. Headphone-Out Jack Headphones or speakers may be connected through this jack.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 4
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring video are outlined in “Video Features” on page 1 - 18. DVMT Notes DVMT is not local video memory. Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table , on page 4 - 3. 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click 2.Install VGA Driver > Yes. 3. Click Next > Yes > Next > Next. 4.
Intel Video Driver Controls Application Mode Note that all figures pictured, and instructions outlined here are based on the Advanced Application Mode. Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® Graphics and Media Control Panel. To access the control panel: 1. 2. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button). OR 3.
Intel Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu tab on the left of the menu and adjusting the settings on the right. Options & Support Click Options & Support and select an item from the sub-menu to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links. Multiple Display At least one other display must be attached in order to view multiple display selection options.
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Display Devices & Options Besides the built-in LCD you can also use an external monitor/flat panel display/TV connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The table below outlines the display options.
Intel Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port or HDMI-Out port on the left of the computer. To Clone Displays: 1. 2. 3. 4. 5. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Clone Displays from the menu. Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls To Enable Extended Desktop: Display Settings Extended Desktop 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) G&M control panel and click Display > Multiple Displays. Click Operating Mode and select Extended Desktop from the menu. Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls Display Profiles You can save display settings to be loaded at any time. 1. 2. 3. 4. 5. 6. 7. Go to the Intel(R) G&M control panel and click Display. Configure the General Settings, Multiple Displays, Color Enhancement, Custom Resolution & Monitor/TV Settings to your preferences. Click Apply, and OK to confirm the settings change. Click the Save button at the top of the General Settings, Multiple Displays or Color Enhancement menus (under Display Profiles).
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Configuring an External Display in Windows 7 You can also use the Screen Resolution control panel in Windows 7 to configure an external display. 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on.
Intel Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 7 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Intel Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your display to the external monitor port or HDMI-Out port, and turn it on. + P key combination. Press the An on-screen menu will pop up.
Intel Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Intel Video Driver Controls 5. 6. Double-click the connected HDMI device (or right-click and select Properties) to adjust the HDMI settings from the control panel tabs. Click OK to close the control panel (see notes overleaf).
Intel Video Driver Controls HHDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display.
Intel Video Driver Controls B B - 14
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processors For All Models Processor For Model A Only Memory Note all processor packages are rPGA Intel® Pentium® B950 (2.10GHz) 2M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Dual Channel DDRIII (DDR3) Intel® Core i7-2620M (2.7GHz) 4M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel® Core i5-2540M (2.6GHz) 3M L3 Cache, 32nm (32 Nanometer), DDR3-1333MHz, TDP 35W Intel® Core i5-2520M (2.
Specifications BIOS Keyboard & Pointing Device Interface AMIBIOS Model A: One 32Mb SPI Flash ROMs Isolated Full Size WinKey Keyboard with Independent Numeric Keys Built-in TouchPad (integrated scrolling key functionality) with Multi Gesture Function Three Instant Keys (WWW, E-Mail, Silent Mode) One Powered USB 2.0 Port One eSATA / USB 2.0 Combo Port Two USB 3.0 Ports One External Monitor Port One HDMI 1.
Specifications Communication Power Management Security 10/100/1000 MB Base-TX Ethernet LAN Supports Wake on LAN Supports Wake on USB Security (Kensington® Type) Lock Slot BIOS Password Fingerprint Reader Module with Trusted Platform Module Support For Model B Only: Intel® vPro Support Intel® Centrino® Advanced-N 6230 (2*2 802.11 a/g/n) Half Mini-Card PCIe WLAN & Bluetooth 3.0 Combo Module (Factory Option) 1.3M or 2.0M Pixel USB PC Camera Module (Factory Option) UMTS/HSPDA-based 3.
