BE SURE TO READ 1. BE SURE TO READ 1-1 INTRODUCTION Thank you for your purchasing MAX LETATWIN LM-380A. This machine is equipped with a variety convenient features that are designed to print on tubes and tapes. To use the machine for a long time, you are recommended to use it in the proper way according to the instruction manual. 1-2 PRECAUTIONS FOR USE [Indications] This operation manual and the machine use various indications in relation to the safe and proper operation of the machine.
BE SURE TO READ WARNING • Never disassemble or remodel the machine –– it can cause a fire, electric shock, or trouble. • Do not put any foreign substance, such a finger, pen, or wire, inside the machine –– it can go out of order or cause a fire or electric fire. • Obtain power directly from an electric outlet. Do not put many loads on one electric outlet –– it can cause a fire. • Never put a heavy substance on a power cord –– the cord can be damaged, leading to a fire or electric shock.
BE SURE TO READ In order to prevent problems with the machine, follow the precautions below. 1. This machine and AC adopter are precision products. Handle them carefully, and do not drop them or allow them to receive any shock or impact. 5. Do not lift up the machine having its cassette cover. The machine may fall. 2. For the consumables other than the tubes (tape cassette, ink ribbon case, cutter, etc), use the specified products only. Never use other products. 3.
BE SURE TO READ 9. Do not place any heavy materials on the dew condensed within the machine due machine or power cable. to the rapid change of the temperature. In this case, leave the machine in the room for more than 30 minutes and use it after confirming that the dew has disappeared. 15. To avoid the cause of trouble, do not use or store the machine in the following 10. Do not put metal fragments or similar places. foreign substances in the card slot, which may cause trouble due to electrostatic.
BE SURE TO READ 1-3 CONTENTS 1. BE SURE TO READ ............................................................................................................... 1 1-1 INTRODUCTION ................................................................................................................. 1 1-2 PRECAUTIONS FOR USE.................................................................................................. 1 1-3 CONTENTS .........................................................................
BE SURE TO READ 6-5-2 MARGIN ................................................................................................................... 39 6-6 VERTICAL ......................................................................................................................... 40 6-7 REPEAT............................................................................................................................. 40 6-8 SEQUENCE...................................................................
BEFORE USE 2. BEFORE USE 2-1 MAIN FEATURES • With simple operation, you can print characters directly on tubes and tapes. • Both high-speed printing (up to 25mm/s) and high durability are achieved. • Usable tubes and tapes are as follows: Max genuine tubes = 3.2mm, 3.6mm, 4.2mm, 5.2mm Generic tubes = 2.5mm, 3.2mm, 3.6mm, 4.2mm, 5.2mm, 5.5mm Shrinkable tubes = 2.5mm, 3.2mm, 3.6mm, 4.2mm, 5.2mm, 5.5mm Max genuine Non PVC tubes = 3.2mm, 3.6mm, 4.2mm, 5.
BEFORE USE 2-2 CONFIRMING THE PACKAGE CONTENTS This machine comes with the following accessories. Confirm that they are included before using the machine.
BEFORE USE 2-3 NAME OF EACH SECTION Hook Cassette cover LCD display Cutter button AC adapter inlet Keyboard Memory card slot Push button Grip Card cover Head pressure switching lever Half cutting depth adjustment lever Platen roller Tape cassette setter M roller lever (silver) Head release lever (green) Tube holder A Half cutter (orange color) M roller (gold color) Half cutter guide (white) Tape cassette Ink ribbon setter Ribbon case Guide Button B Button A 9 Winding core (black) Ribbon c
BEFORE USE 2-4 NAME OF KEYS AND THEIR FUNCTIONS <1> Keyboard layout 2 1 4 3 6 1 1 1 11 1 8 9 5 7 <2> Keys and their functions 1 ON/OFF 2 ESC Press this key to turn ON/OFF the power supply. Press this key to return to the previous menu and not to make any changes. When printing or displaying an “IMAGE,“ cancel the operation. P.MATERIAL Press these key to set the “PRINETD MATERIAL” when changing material (SHIFT without turning off.
BEFORE USE Press this key to operate the “MEMORY OF WORD” function. WORD (See 6-11: MEMORY OF WORD) OPTION IMAGE (SHIFT 3 OPTION) Press this key to change the “OPTION” setting. (See 6-13: OPTION) Press these keys to display the printing image. (See 6-12: IMAGE) Press this key to operate the “MEMORY” function. MEMORY (See 6-15-1: INTERNAL MEMORY) COPY Press these keys to copy the block indicated by the cursor. (SHIFT MEMORY) (See 6-14-1: COPY) Press this key to operate the “CARD” function.
BEFORE USE 10 SPACE Press this key to input a space. 11 A/ a Press this key to switch capital letters to small letters. 12 SHIFT Press this key to access secondary characters on the key or the secondary functions of group PRINT 13 14 Press this key to move to the “PRINT” function. FEED (SHIFT PRINT) Character keys 15 Press these keys to feed tubes or tapes. Press these keys to input characters. Press this key to change lines.
BEFORE USE The meanings of edit marks displayed on the screen are as follows. (1) : Represents the [PITCH PRINT MODE] activated. Represents a group of blocks with same pitch length until next [P] mark. (2) (See 6-4: PITCH PRINT) : Represents the block. Up to 100 blocks can be input in an entire document. (See 6-4: PITCH PRINT) (3) : Represents the line feed. (Printing on tubes) 2.5 to 4.2 : Only 1 line can be set. 5.2 and 5.5 : Up to 2 lines can be set, provided 2mm character size are used.
BEFORE USE 2-7 CLEANING THE PLATEN ROLLER OR REMOVING A JAMMED TUBES (“FEED” function) 1. Open the cassette cover. 2. While pressing C , press ON/OFF for about 3 seconds. Then, release ON/OFF first while displaying the logo of “LETATWIN.” 3. [FEED screen] appears. B> 4. Slide the switching lever (silver) until it stops. 5. Put wet cloth with water or alcohol to the platen roller and clean it using / key. Note: If the tube is jammed, remove the consumables using this “FEED” function.
BEFORE USE 2-8 ADJUSTING THE HALF CUTTING DEPTH You can adjust the half cutting depth with the ”Half cutting depth adjustment lever”, when half cutting is too deep. Deep Note: When printing on tubes, the leaver has to be positioned on the “TUBE.” When printing on tape, the lever has to be positioned on the “TAPE.” Shallow 2-9 SWITCHING THE HEAD PRESSURE You can change the strength of head pressure with the “Head pressure switching lever.
LOADING THE CONSUMABLES 3. LOADING THE CONSUMABLES Follow the steps bellow. (1) Installing the ink ribbon to the ink ribbon case. (2) Loading the tube or tape. (3) Loading the ink ribbon case. 3-1 INSTALLING OR REPLACING THE INK RIBBON Name of each section The side with letters comes the top. Button B Top (Transparent) Bottom Ribbon case Winding core (Black) Button A Ribbon core (Green) Note: Use a ribbon case (LM-RC310) for LM-380A. Don’t use a ribbon case (LM-RC300) for LM-370A. 1.
LOADING THE CONSUMABLES The color changes. 3. Rotate the ink ribbon toward the direction of the arrow until the black surface appears. (The color changes in the order of transparent blue black) When the surface (black) has appeared, stop rotating. 2. Rotation Replacing the ink ribbon, first remove the ink ribbon from the ribbon case. 1. While pressing “Button B,” take out the ribbon core (green) from the ribbon case. Button B 2.
LOADING THE CONSUMABLES 3-2 LOADING THE TUBES AND THE INK RIBBON CASE 1. Open the cassette cover. 2. Push the head release lever (green). Head release lever 3. Slide the switching lever (silver) until it stops. Switching lever 4. a: Pass the tubes under the holding plate. b: Extrude the tip of the tubes by 1 J 2cm from the machine. Holding plate Pull out 1~2cm 5. Place and hold the tube on the “TUBE” label and slide the “Switching lever” to lock.
LOADING THE CONSUMABLES The tube has been loaded. Make sure the tube is loaded as illustrated bellow. 6. Make sure the ribbon is not slack. If the ribbon is slack, rotate the winding core (black) toward the direction of the arrow to remove the slack of the ribbon. 7. Hold the ink ribbon case as illustrated below and load it completely. Proper loading Check the slack.
LOADING THE CONSUMABLES 8. Pull the head release lever (green). 9. Close the cassette cover until it clicks. (Removing the tube) 1. Open the cassette cover. 2. Push the head release lever. 3. Slide the switching lever (silver) until it stops, then remove the tube. Note: You don’t need to remove the ink ribbon case when removing tube. 4. Pull the head release lever (green), then close the cassette cover until it clicks. Caution Be careful when operating the Head release lever.
LOADING THE CONSUMABLES 3-3 LOADING THE TAPE CASSETTE AND THE INK RIBBON CASE 1. Open the cassette cover. 2. Push the head release lever (green). Head release lever 3. Slide the switching lever (silver) until it stops. Remove Switching lever 4. Load the tape cassette. Proper loading Before loading the tape cassette, prepare it as illustrated below. (1) Pass the tape through the guides. (2) Pull out the tip of the tape by about 4cm. about 4cm Guide 5. Make sure the ribbon is not slack.
LOADING THE CONSUMABLES 6. Hold the ink ribbon case as illustrated below and load it Proper loading Note: Make sure the ribbon is not slack. 7. Pull the head release lever (green). 8. Close the cassette cover until it clicks. (Removing the tape cassette) 1. Open the cassette cover. 2. Push the head release lever. 3. Remove the tape cassette Note: You don’t need to remove the ink ribbon case when removing tape cassette.
LOADING THE CONSUMABLES 4. Pull the head release lever (green), then close the cassette cover until it clicks. 3-4 REPLACING THE HALF CUTTER 1. Open the cassette cover. Half cutter 2. Pull out the half cutter. 3. Engage the guide of the half cutter to the groove of the half cutter holder and insert it completely. Guide Note: Engage the guide of the half cutter to the groove of the half cutter holder.
LOADING THE CONSUMABLES Push button To remove the card, press the push button.
BASIC OPERATION BASIC OPERATION 4. 1. Open the cassette cover and load the consumables to use. (See 3: LOADING THE CONSUMABLES) Then, close the cassette cover and turn the power on. 2. [PRINTED MATERIAL setting screen] appears. Press / / / key to set “PRINTED MATERIAL” and “SIZE.” Press K .QP R / 7 > / R S T1 R U )V / 'W X 7Y -V -Z[ '+ ENTER , and then [INPUT screen] appears.
BASIC OPERATION 4-1 PRINTING ON THE TUBE (PITCH PRINT) Printing the following contents on the tube. Tube size= 3. 2 mm Pitch length= 18mm U1 COM X1005 X1006 X1007 1pcs. 5pcs. 2pcs. 2pcs. 2pcs. 18mm 18mm 18mm 18mm 18mm 1. Set “MATERIAL = TUBE” and “SIZE = 3.2mm” in the [PRINTED MATERIAL setting screen]. 2. [INPUT screen] appears. Make sure that Press 3. Press A is turned on. / key to move the cursor to PITCH . PITCH LENGTH) Press / key to set “18.0.
BASIC OPERATION 8. As same as “4”, press 9. Input X . Press RPT SEQ to set “Repeat” to “2.” Press to set “SEQUENCE.” (See 6-8: SEQUENCE) ENTER . !a %Z< d 2' ENTER to select “10 scale.” Set the “START > 2 7ee Input Press 1 0 0 5 in the “START.” 7 !a %Z< 2' ' 2' ' B N + a -, B R aV fV ' > key to set the “END.” Input 1 0 0 Press ENTER . 2> B NUMBER” and “END NUMBER.” ! ! B PRINT .
BASIC OPERATION 4-2 PRINTING ON THE TAPE 4-2-1 PITCH PRINT ON THE TAPE Printing the following contents on the tape. Tape size= 9mm U1 15mm Pitch length=15mm SLD SLD SLD SLD SLD SLD X18 X19 X1A X1B X1C X1D 15mm 15mm 15mm 15mm 15mm 15mm COM COM 15mm 15mm 1. Set “MATERIAL=TAPE” and “SIZE=9mm” in the [PRINTED MATERIAL setting screen]. 2. [INPUT screen] appears. Make sure that Press / key to move the cursor to 3. Press PITCH . -Z< to set “PITCH LENGTH.
BASIC OPERATION 7. Pressing ENTER . Set the “START NUMBER” and “END NUMBER.” Input 1 8 Press Input Press C D ' > R aV fV BLOCK Press / ENTER . !ac%Z< to set “REPEAT.” (See 6-7: REPEAT) key to set “2.” Press ' R P P h , , ! ' N B V P 2 Note: It is also possible to input the value by pressing Ten key. !ac%Z< ' N B 10. Press PRINT .
BASIC OPERATION 4-2-2 NORMAL PRINT ON THE TAPE Printing the following contents on the tape. MAX LETATWIN 12mm LM-380A 40mm 1. Set “MATERIAL=TAPE” and “SIZE=12mm” in the [PRINTED MATERIAL setting screen]. 2. [INPUT screen] appears. Make sure that Press / key to move the cursor to A is turned on. . 3. In order to change to [NORMAL PRINT MODE], press DELET to delete . (See 6-5: NORMAL PRINT) SHIFT .QP R SIZE (TP/LNG) and set “PRINTING LENGTH.” (See 6-5-1: Printing length) Press / 4 5.
BASIC OPERATION 6. [INPUT screen] appears. Press after . Input M W I 0 A. 7. Press A N PRINT X L key to move the cursor SPACE L M SHIFT E T A T A 3 8 to start printing. (See 7: PRINTING) 8. The printed result is as shown.
INPUTTING AND DELETING CHARACTERS 5. INPUTTING AND DELETING CHARACTERS 5-1 INPUTTING CHARACTERS 1. To input the capital letter “A.” 1) Press A/a 2) Press A . and make sure that the indicator of n P B A is turned on. A 2. To input the small letter “a.” 1) Press A/a 2) Press A n and make sure that the indicator of . P B a P B a is turned on. 3. To input “+.” 1) Turn on 2) Press S SHIFT . + . 5-2 DELETING CHARACTERS 1. DELET : 1) Press DELET .
INPUTTING AND DELETING CHARACTERS 5-3 INPUTTING CHARACTERS WITH “CODE” FUNCTION Using the “CODE” function, you can input the characters according to the following table. M (In case English is selected as the screen language.) [ The Table of Code ] Code 0 No. 1 2 2 3 4 5 6 7 8 9 A B C D E F ! “ # $ % & ‘ ( ) * + , - .
USING FUNCTIONS USING FUNCTIONS 6. The following table shows the setting items and their default values. SETTING ITEM DEFAULT VALUE Printed material No setting Size of printed material No setting Character size AUTO: ON Sequence No setting Character width STANDARD Justification CENTER Character space STD 6, 9 mark (6_ 9_) Line space STD Printing density 4 TAPE: 10.0 mm Cutting position 0.0mm TUBE: 20.
USING FUNCTIONS The selectable “CHARACTER SIZE” varies depending on the “SIZE” of the material, the “PITCH LENGTH” and the number of lines, etc. 6-2 WIDTH Setting the “CHARACTER WIDTH” at the cursor position. Selectable items: STANDARD, CONDENSED, EXTENDED Note: You can select “CHARACTER WIDTH” according to the following table.
USING FUNCTIONS 6-3 CHARACTER / LINE SPACE Setting the “CHARACTER / LINE SPACE” for the document. Selectable items: “CHARACTER SPACE” = STD (STANDARD), CLS (CLOSE), CNT (CONTACT), WID (WIDE) “LINE SPACE” = STD (STANDARD), CLS (CLOSE), WID (WIDE), CNT (CONTACT) A B C C D Character space 1. Press Line space E . 2'` C/SPC . The [CHARACTER / LINE SPACE setting screen] appears. 2 key to move the cursor to the “L / SPACE.” 2 2 4. Press ENTER .
USING FUNCTIONS 6-4 PITCH PRINT [PITCH PRINT MODE] on the top means that LM-380A is in the [PITCH PRINT MODE]. By deleting the , you can switch to the [NORMAL PRINT MODE]. [NORMAL PRINT MODE] [PITCH PRINT MODE] -Z< P B 2' B P ' "! (See 6-5: NORMAL PRINT) ! -, , ' -Z< 2' Note: In the [PITCH PRINT MODE], you can print every block ( and the center as illustrated bellow.
USING FUNCTIONS 6-4-1 PITCH LENGTH Setting the “PITCH LENGTH” at the cursor position. Setting range: “Tube” = AUTO, 10.0 v 60.0mm, “Tape” =AUTO, 4.0 v 60.0mm -Z< and press 1. Press / key to move the cursor under P PITCH . P B / >> >^ V LENGTH.” P ENTER , the “PITCH LENGTH” is set and the [INPUT screen] appears. , P B 7 2'` , >> >^ ' -Z< , -Z< P B ` 2' V 3.
USING FUNCTIONS 6-5 NORMAL PRINT [NORMAL PRINT MODE] In the [NORMAL PRINT MODE], the pitch function is not available and you can print a tape or tube up to 300mm as the total printing length. Deleting in the [INPUT screen]. [NORMAL PRINT MODE] [PITCH PRINT MODE] -Z< P B 2' B ' "! P ! -, , ' -Z< 2' ' "! P ! -, , ' 6-5-1 PRINTING LENGTH Setting the total length of the document.
USING FUNCTIONS 6-6 VERTICAL Setting to print a document vertically. Selectable items: YES (vertical), NO (horizontal) Note: The printed result varies depending on the selected “PRINT MODE.” HORIZONTAL VERTICAL Tube COM Tape COM Tape COM PITCH PRINT NORMAL PRINT 1. Press COM MATERIAL C O M PRINT MODE C O M You can select “PRINTING DIRECTION” according to the following table. . VRT . The [VERTICAL setting screen] appears. . 2. Press / key to select. Note: ENTER .
USING FUNCTIONS 1. Press -Z< RPT . The [REPEAT setting screen] appears. R P R P B P ' "! V -Z< 2. Press / key or Ten key to input the value of the “REPEAT.” 3. Press P B 2' 2' V P ! P 2' ' "! 2' ENTER . Note: You can change the default value of “REPEAT” in the “OPTION” setting. 6-8 SEQUENCE Setting sequential number. To activate “SEQUENCE” function, set the “START” number and “END” number as below.
USING FUNCTIONS 4. Press key to move the cursor to the “END.” And then Press / key or Ten key to input the value of the “END.” -Z< P B ' > 5. Press Note: 2' ' "! R aV fV !a ENTER . Make sure that set both the “START” number and the “END” number. In the [PITCH PRINT MODE], you can set only one series of “SEQUENCE” in one block and up to 15 series of “SEQUENCE” in one document. In the [NORMAL PRINT MODE], you can set only one series of “SEQUENCE” in one document.
USING FUNCTIONS 6-10 SYMBOL Inputting various symbols. Selectable group of symbols: NUMERAL, ALPHABET IN CIRCLE, UNIT OFFICE SYMBOLS, SUPERSCRIPT, SUBSCRIPT, ELECTRICAL INSTALLATION ] , ITALIC, GREEK LARGE RUSSIAN, SMALL RUSSIAN Note: “LARGE RUSSIAN” and “SMALL RUSSIAN” can be displayed in the LM-380A A11-C, BSA and CE selected the English as the “screen language”. Please confirm the model of your LM-380A. 1. Press SHIFT SEQ (SYMBOL). The [SYMBOL select screen] appears.
USING FUNCTIONS 6-11 REGISTRATION OF WORD You can save up to 30 words in the internal memory. Each word contains up to 15 characters. , Note: 1. Press , and WORD . cannot be saved. The [MEMORY OF WORD setting screen] appears. -Z< P B .0/ / R 2. Press / key to select a desired item and press 2' R 2> ' "! R \ Bsi )1 ENTER . Selectable Items: RECALL, SAVE, DELETE, INITI.(INITIALIZE) [SAVE] Saving the “WORD.” 1. Select “SAVE.
USING FUNCTIONS [RECALL] Recalling the saved “WORD.” 1. Select “RECALL.” And then press ENTER . -Z< P B .0/ / R 2. Press / key or Ten key to input the desired file No. Then the word of the desired file is displayed as the bottom of the screen. 3. Press ENTER ' "! R \ Bsi 2> )1 -Z< 2' ' "! P B B % >\ > V ! to input the word at the cursor position. [DELETE] Deleting the registered “WORD.” 1. Select R 2' DELETE . And then press ENTER .
USING FUNCTIONS 6-12 IMAGE Previewing a document to get the following information about tubes and tapes before printing. 1) Total print length 2) Preview of the document key: Temporarily stops the “IMAGE” scroll. key: Increases the scroll speed. key: Reduces the scroll speed. ESC : Cancel the preview. 6-13 OPTION Press OPTION . The [OPTION setting screen] appears. The selecting items in the “OPTION” are as follows. . P R 7 P & >^ % )s 2' + .
USING FUNCTIONS 6-13-2 LOW TEMP. MODE You can get the printing result darker or clearer by this mode besides adjusting the “PRINTING DENSITY.” . % )s / P / 4 1 LOW TEMP. MODE PRINTING SPEED YES About 10 mm/s NO About 25mm/s Note: When this function activates, printing speed is changed as the above table. 6-13-3 LCD BRIGHTNESS Adjusting the “LCD BRIGHTNESS.” When the screen is not clear, adjust the “LCD BRIGHTNESS” level.
USING FUNCTIONS 6-13-5 POSITION OF PRINTING LINE Adjusting the “POSITION OF PRINTING LINE.” By pressing / key, increase or decrease the position of printing line. Press ENTER to register the setting. (Printed result) .QP j 7j U \ B P R 7 & >^ i 7 A1 (Increment) ABC ! (Decrement) 6-13-6 CUTTING POSITION Adjusting the “CUTTING POSITION.” By pressing / key, increase or decrease the cutting position. Press ENTER to register the setting. Setting range: -2.0 v +2.0mm .
USING FUNCTIONS 6-13-8 DEFAULT VALUE OF “PITCH LENGTH” Setting the default value of “PITCH LENGTH.” Note: The default value is set initially as “TUBE = 20mm and TAPE = 10mm” at our factory. After setting the desirable value by pressing / / / key, press ENTER to register the setting. Setting range .QP “Tube” £ 10.0 v 60.0mm ¢ 7 2'` + V P Note ¡ If you press the >> ^ `%1 ,', “Tape” £ 4.0 v 60.
USING FUNCTIONS 6-13-10 JUSTIFICATION Setting the “JUSTIFICATION” for a document in the [NORMAL PRINT MODE]. Note: This setting is only applied to the [NORMAL PRINT MODE]. The character arrangement in the [PITCH PRINT MODE] is always “CENTER.” After selecting the item by pressing / key, press ENTER to register the setting. Selectable items: LEFT, CENTER, RIGHT .
USING FUNCTIONS 6-13-12 FEED THE HEAD OF TUBE Setting the “FEED THE HEAD OF TUBE”. After selecting the item by pressing . > B > / key, press ENTER to register the setting. ` ` 4 B '+ 1 This function is available only when printing on tube. Note: When “YES” is selected, the head of tube (approx.55mm) can not be printed. 6-14 COPY / PASTE You can copy a block in the document and paste it to the cursor position.
USING FUNCTIONS 6-15 MEMORY 6-15-1 INTERNAL MEMORY You can save the created document and its setting values in the internal memory. The saving capacity is up to 20 documents and up to 40,000 characters in total (according to the setting contents). , , 1. Press and can also be saved. .0/ MEMORY . The [MEMORY setting screen] appears. R / 2> R >> 2. Press / / / key to select a desired item and press %1 & 7j ENTER . Selectable items: RECALL, SAVE, DELETE, INITI.
USING FUNCTIONS [RECALL] Recalling the saved document. 1. Select RECALL . And then press .¥R ENTER . B % > The [FILE NO. inputting screen] appears. V P B Note: ! + À 2. Press / key or Ten key to select the desired file No. Press 2> ' T1 B ENTER to recall the file. If there is a document created in the [INPUT screen], the overwrite message appears. [DELETE] Deleting the saved document 1. Select DELETE . And then press ENTER . .
USING FUNCTIONS 6-15-2 EXTERNAL MEMORY You can save the documents in the memory card (CF card). The data format can be selected from “CSV” or “LMF” format. The data formatted by “CSV” can be edited by Excel of Windows in a personal computer. The data formatted by “LMF” can be edited by MAX original application software “LETATWIN PC EDITOR” in a personal computer. (See 8: EDITTING DATA IN PERSONAL COMPUTER) 1. Insert the CF card into LM-380A. 2. Press (See 3-5: INSERTING THE MEMORY CARD) CARD .
USING FUNCTIONS FILE Displays the next file. Displays the file name. To save, input the name within 8 alphanumeric characters. DATE Displays the date when the file is created. To save, input the last two digits of the year/month/date. 5. To save the document, input all of the above items with alphanumeric characters. The following alphanumeric characters can be inputted. - 0 1 2 3 4 5 6 7 8 9 @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 6.
PRINTING 7. PRINTING Printing the created document. 7-1 PRINT RANGE SETTING SCREEN You can print desired blocks by inputting block No. 1. Press PRINT . [PRINTING RANGE setting screen] 7 P A >V ! ! 2> appears. Setting value: .QP R COPIES: 1 v 10 %1 ' R V > V START NO. = 1 END NO. = The last block No. of the created document.
EDITTING DATA IN THE PERSONAL COMPUTER 8. EDITTING DATA IN THE PERSONAL COMPUTER You can edit the “CSV” and “LMF” data through the memory card (CF card) that is created with “LETATWIN PC EDITOR” in the personal computer. “CSV” data includes only document data. “LMF” data includes document and setting data. Note: How to use “LETATWIN PC EDITOR” Please see the “HELP menu” of “LETATWIN PC EDITOR” after installing it.
TROUBLE SHOOTING 9. TROUBLE SHOOTING 9-1 ERROR MESSAGE LIST Error message Contents Solution OVER INPUT CHARACTER NO. Number of characters inputted has exceeded 2,000 characters. Characters more than 2,000 cannot be inputted. OVER NO. be inputted has exceeded 4 lines. INPUT LINE Number of lines of the document to The maximum lines are 4 lines. OVER INPUT BLOCK Number of blocks of the document Blocks more than 300 cannot be NO. has exceeded 300 blocks. inputted.
TROUBLE SHOOTING Error message Contents Solution INITIALIZE AFTER It was attempted to initialize the Implement the initialization of setting DELETE ALL FILES setting while inputting a document. after deleting all documents. NO INPUT FILE It was attempted to print without a Implement the print after inputting the file to be created. file. OVER PRINTING SIZE The file to be printed is Change number of lines, space overflowing from the print material between lines or character size. now editing.
TROUBLE SHOOTING 9-2 TROUBLESHOOTING Problem 1. The power is on but: 1) The screen does not turn on. 2) The screen is dark (or too light) 1. When printing to the tube: 1) It does not print. 2) The printing is blurred (thin). 3) It does not print sporadically. 4) The printing is stained (thick). Solution • Make sure that the power cable is firmly connected to the plug socket, the adapter and the unit.
TROUBLE SHOOTING Problem 3. When printing to the tape: 1) The tape cannot be set. 2) It does not print. 3) The printing is blurred (thin). 4) The printing is stained (thick). Solution • Make sure the position of the switching lever. • Make sure that the tape has properly been set. • Make sure that the setting value for the tape width is correct. • Make sure that the ink ribbon has properly been set. • Make sure that there is no dirt, oil stain, etc attached to the tape.
TROUBLE SHOOTING Problem Solution 6. The external memory does not • Check that the card has been inserted in the card slot save data. up to the end. • Check that the memory capacity is sufficient. Ã If the problem is not remedied with above corrective actions, contact your dealer.
PRODUCT SPECIFICATIONS 10. PRODUCT SPECIFICATIONS ITEMS CONTENTS Dimensions 286(W)x267(D)x95(H)mm Weight 2Kg Printing method Thermal transfer method (300 dpi) Display LCD dot matrix: 64 X 132 pixel Printing speed 25mm/s (Standard) 10mm/s (Low temperature mode) Maximum printing length Tube: 20m, Tape: 5m Maximum number of characters 2,000 characters to input Character size Usable tube 2, 3, 4, 6mm height 2.5 to 5.
APPENDICES 11.
