ENGLISH HN65J HIGH PRESSURE METAL CONNECTOR NAILER INDEX 1. SAFETY INSTRUCTIONS ..................................4 2. SPECIFICATIONS & TECHNICAL DATA .............................................7 3. AIR SUPPLY AND CONNECTIONS ...................8 4. INSTRUCTIONS FOR OPERATION...................9 5. MAINTAIN FOR PERFORMANCE ................... 13 6. STORING.......................................................... 13 7. TROUBLESHOOTING/REPAIRS .....................
1. SAFETY INSTRUCTIONS ! WARNING: TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING "SAFETY INSTRUCTIONS". FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR SERIOUS INJURY. PRECAUTIONS ON USING THE TOOL 1. WEAR SAFETY GLASSES OR GOGGLES Danger to the eyes always exists due to the possibility of dust being blown up by the exhausted air or of a fastener flying up due to the improper handling of the tool.
8. INSPECT SCREW TIGHTNESS Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put into operation. Inspect to confirm that all screws and bolts are tight and properly installed prior to operating the tool. 9. DO NOT TOUCH THE TRIGGER UNLESS YOU INTEND TO DRIVE A FASTENER Whenever the air supply is connected to the tool, never touch the trigger unless you intend to drive a fastener into the work.
18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE When fastening roofs or similar slanted surface, start fastening at the lower part and gradually work your way up. Fastening backward is dangerous as you may loose your foot place. Secure the hose at a point close to the area you are going to drive fasteners. Accidents may be caused due to the hose being pulled inadvertently or getting caught. 19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g.
2. SPECIFICATIONS 1. NAME OF PARTS Frame Cylinder Cap Contact Arm Nose Magazine Trigger Grip Exhaust Cover Trigger Lock Dial Aiming Guide Locator 2. TOOL SPECIFICATIONS PRODUCT NO. HEIGHT WIDTH LENGTH WEIGHT RECOMMENDED OPERATING PRESSURE LOADING CAPACITY AIR CONSUMPTION 3. FASTENER SPECIFICATIONS HN65J 11-1/2” (291 mm) 4” (102 mm) 11-1/2” (291 mm) 4.4 lbs. (2.0 kg) 170 to 320 p.s.i. (12 to 23 bar) 100 Nails 1.4 ℓ at 257 p.s.i.
! WARNING: 3. AIR SUPPLY AND CONNECTIONS Read section titled "SAFETY INSTRUCTIONS". DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR The tool is designed to operate on compressed air. Do not operate the tool on any other combustible gases (e.g., oxygen, acetylene, etc.) since there is the danger of an explosion. For this reason, absolutely do not use anything other than an air compressor to operate the tool.
4. INSTRUCTIONS FOR OPERATION Read section titled "SAFETY INSTRUCTIONS". 1. BEFORE OPERATION Wear Safety Glasses or Goggles. Do not connect the air supply. Inspect screw tightness. Check operation of the contact arm & trigger if moving smoothly. Connect the air supply. Check the air-leakage. (The Tool must not have the air-leakage.) Hold the Tool with finger-off the trigger, then push the contact arm against the work-piece. (The tool must not operate.
Door Latch NAIL LOADING Open the Magazine: Pull up Door Latch and swing Door open. Swing Magazine Cover open. When using 40 mm (1-1/2”) nails, attach the nail support in such a manner that a mark “40” can been seen. When using 65 mm (2-1/2”) ones, attach the nail support upside down. Nail Support 65 mm (2-1/2”) 40 mm (1-1/2”) To detach, push the latch on the back of the magazine with a finger. Nail Feed Pawl Nail loading: Place a coil of nails over the Nail Post in the Magazine.
TEST OPERATION X Adjust the air pressure at 170 p.s.i. (12 bar) and connect the air supply. Y Without touching the Trigger, depress the Contact Arm against the work-piece. Pull the Trigger. (The tool must fire the fastener.) Z With the tool off the work-piece, pull the Trigger. Then depress the Contact Arm against the work-piece. (The tool must fire the fastener.) [ Adjust the air pressure as much as the lowest possible according to the diameters and length of fastener and the hardness of work-piece.
DRIVING DEPTH ADJUSTMENT DIAL Adjustment Dial ! WARNING: ALWAYS disconnect air supply before adjustment dial. With air pressure set, drive nails into a representative material sample to determine if adjustment is necessary. If adjustment is required, disconnect air supply. Refer to the mark on the Adjust Spacer for direction to turn the adjustment dial. Reconnect air supply. Deeper Shallow Deeper Shallow TRIGGER LOCK MECHANISM The tool is equipped with a Trigger Lock Mechanism.
5. MAINTAIN FOR PERFORMANCE X DO NOT FIRE THE NAILER WHEN IT IS EMPTY Y USE RECOMMENDED OIL The velocite or turbine oil should be used to lubricate the tool. Upon completion of operations, place 2 or 3 drops of oil into the air plug inlet with the jet oiler. (Recommended Oil : ISO VG32) Z INSPECT AND MAINTAIN DAILY OR BEFORE OPERATION ! WARNING: Disconnect air supply and empty the magazine when inspecting or maintaining the tool.
6-6 NIHONBASHI-HAKOZAKI-CHO, CHUO-KU, TOKYO, JAPAN Tel: (03) 3669-8131 Telefax : (03) 3669-7104 http://www.maxusacorp.com (USA Site) http://www.max-ltd.co.
SuppIément au mode d’emploi Selon Ia norme européenne EN 792-13 le réglement suivant est valable du 1.1.2001, que toutes machines à enfoncer les fixations équipées de commande par contact doivent être marquées avec le symbole ,,Ne pas utiliser sur des échafaudages ou e’chelles,, et elles ne seront pas utilisées pour utilisations spécifiques, par example: - en cours de déplacement d’ un lieu d’ enfoncement à l’autre sur des échafaudages, escaliers, échelles ou constructions de même qu ‘ êchelles comme p.e.
