Full Product Manual

ManualsBrandsMax Load ManualsAutomotive2000 lb. Payload Capacity Side Wind Trailer Jack with Dual Wheels and Horizontal Mounts

*Actual product may vary slightly

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.

Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property

damage and/or personal injury. Please keep instructions for future reference.

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

This product contains or, when used, produces a chemical

known to the State of California to cause cancer and birth

defects or other reproductive harm.

(California Health & Safety Code § 25249.5, et seq.)

WARNING

36210

2,000 LB. CAPACITY DUAL WHEEL

SWING-BACK BOAT TRAILER JACK

For Customer Service, Call 1-800-348-5004

or e-mail customerservice@focus-ontools.com

36210 03/2017

Summary of content (8 pages)

PAGE 1
36210 2,000 LB. CAPACITY DUAL WHEEL SWING-BACK BOAT TRAILER JACK WARNING This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.) *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others.
PAGE 2
SPECIFICATIONS Rated Capacity Height Range Wheel Diameter 2,000 lbs 14-1/4” to 26-1/4” 6” SAFETY WARNINGS 1. Do not exceed rated capacity. 2. Lock Trailer Jack in vertical position before applying load. 3. Use on flat, level, hard surface capable of supporting load. 4. Wear ANSI-approved safety goggles during use. 5. Prevent trailer wheels from moving using wheel chocks while raising or lowering. 6. Before towing, fully raise trailer jack and secure properly in its horizontal position. 7.
PAGE 3
17. Do not disconnect the boat trailer and use this Trailer Jack to roll the boat down the boat ramp. 18. Follow all state regulations for boat safety and towing when using Trailer Jack, including using safety chains securely attached to the towing vehicle when the trailer is hooked to the vehicle. 19. Not for aircraft purposes. 20. Trailer Jack must always be in the folded up position (horizontal to ground) when towing the trailer. 21.
PAGE 4
MOUNTING Bolt Square or Rectangular Trailer Tongue Insert Bolts in this direction Figure B Mounting Plate WARNING: The trailer tongue must be square or rectangular in profile for this Jack to mount properly. A cylindrical tongue will allow the Jack to rotate off to the side and the trailer may suddenly fall, potentially causing serious personal injury or property damage. Do not drill holes or otherwise damage the trailer tongue when installing this Jack, as failure of the trailer tongue may result.
PAGE 5
DISMOUNTING 1. Before dismounting, chock the trailer wheels to prevent the trailer from rolling. 2. With the trailer on the hitch, pull and release the Swivel Handle, allowing the Jack to swing downwards. Keep fingers away from the Swivel Plate area, and feet away from the Wheels as the Trailer Jack swings downward. 3. Assure that the spring loaded Swivel Handle pin locks the Jack into the lowered position. 4. Rotate the Crank clockwise to raise the Jack, lowering the Wheels to the ground.
PAGE 6
5. Turn the Crank counterclockwise to lower the Jack slightly, transferring the trailer weight onto the towing vehicle. 6. Pull out the Swivel Handle, and rotate the Jack into its horizontal position. Assure that the Swivel Handle pin is in place, locking the Jack into the raised horizontal position before moving the trailer. 7. Attach the safety chain (sold separately).
PAGE 7
PARTS LIST AND ASSEMBLY DIAGRAM Part 1 2 3 4 5 6 7 8 9 10 11 Description Qty Lock Nut Swivel Plate Spring Washer Bearing Washer Screw Rod Inner Tube Bolt Wheel Lock Nut 4 1 1 1 1 3 1 1 1 2 1 Part 12 13 14 15 16 17 18 19 20 21 Description 19 Part Qty Outer Tube Clip Spring Pin Gear A Plastic Cover Gear B Washer Bushing Handle Lock Nut 22 23 24 25 26 27 28 29 30 31 1 1 1 1 1 1 1 1 1 1 Description Qty 1 1 1 1 4 2 4 4 4 1 Handle Grip Bolt Bracket Large Washer Bolt Connecting Plate Nut Spring Wash
PAGE 8
Limited Manufacturer Warranty FOT makes every effort to ensure that this product meets high quality and durability standards. FOT warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.