User's Manual

User’s Guide
Supporting the handsfree and headset profile
Compatible with Nokia: 8910, 8910i, 6310, 6310i,
6600, 3650, N-Gage, N6230, 6820 Ericsson:T39,
T68 Sony Ericsson:T68,T68i,T610, T630, P800,
P900, Z600 Philips: Fisio820, Fisio 826 Panasonic:
X70 Siemens:S55, SX1, Motorola:V525, V600, A760
Sharp: GX-T15, GX-T21,GX-T31
1.Charging the battery:
When the battery is new, it is not fully charged. It takes 4 hours to fully charge the battery. Afterwards it will take 2 hours to fully
charge the battery. There are two modes of charging:
(1)Plug the travel charger into the AC outlet and the indicator of the adaptor will turn on. Connect the adaptor into the charging
status of the headset. The red indicator of the headset will light on. When the battery is full, the red indicator will be off. Disconnect
the adaptor from the headset.
(2)Plug the USB cable to the charging status of the headset. The red indicator of the headset will light on. The battery is now being
charged. When the battery is full, the red indicator will be off. Disconnect the USB cable from the headset.
2.Turning the headset on or off:
(1) Press the “Button 1 ” for 5 seconds. You will hear two beep sounds and the blue indicator begins to flash every 3 seconds. The
headset is now powered on.
(2) When the power is on, press the “Button 1 ” for 3 seconds. You will hear two beep sounds and the red indicator will flash, then
the headset is turned off.
3.Pairing the headset:
(1)The headset must be powered off before you begin to initiate the pairing. Press the “Button 1” for six seconds, and the blue and
red indicators will begin to flash alternatively. The headset is now in pairing mode.
(2)Initiate the pairing process of your bluetooth mobile phone. (Please refer to the manual of your mobile phone.)
(3) When asked the PIN code, please enter “0000” to successfully complete the pairing process.
(4)When the pairing process is successfully completed, the blue indicator will flash 3 times every 3 seconds. The headset is now in standby
mode.
Note:
(1)If the headset is not in pairing mode, your mobile phone can not find the headset. Please set the pairing the headset into
pairing mode before you start to connect the headset with your phone.
(2)If no pairing is possible over a period of time (Aprox. 1minute), the pairing process will be stopped. You have to repeat STEP 3
to successfully complete the pairing.
4.Answering or ending calls:
When the headset is paired with your phone, and when there is an incoming call, you will hear a musical beep. Then press the “
Button 1” to answer the call. When there is a call in session, you can press the “ Button 1 ” to end the call.
Note: Due to the different design of some mobile phones, an auto-disconnect may happen even when the Headset is powered on. In that case,
the headset won’t ring when there is an incoming call. Press “Button 1” for 1 second to reconnect the Headset with the mobile phone for
an incoming call.
5.Making calls:
(1) Voice-dialing:
Press the “Button 1”. After hearing a beep sound, say the name of the person you recorded on your phone.
(The availability of this function depends on the design of the mobile phone you use. Please refer to the manual of your mobile phone
for voice-dialing function. )
(2) Dial the phone number on you mobile phone as you normally do. The sound will be transmitted to the headset automatically.
6.Changing the volume of the Headset:
(1) Press the “Button 2” to increase the listening volume of the headset.
(2) Press the “Button 3 ” to decrease the listening volume of the headset.
(3) You can also adjust the volume from your mobile phone.
7.Redialing the call:
After ending the call, you can press the “Button 2” to redial the call you just ended.
(The availability of this function depends on the design of the mobile phone you use. Please refer to the manual of your mobile phone.)
8.Mute function:
You may have to keep a call on line while talking to others. Push the “Button 2” and the “Button 3” at the same
time for one second. You will hear continuous beep sounds. Now the headset is in “mute function” mode. To disable the “mute function”,
press the “Button 2 ” and the “Button 3” once again.
9.Rejecting a call
When there is a call in session, you can press the “Button 1” for three seconds to reject a call.