mATX AIMB-562 Series Intel® Core® 2 Duo / Pentium® D / Pentium® 4 / Celeron® mATX Main Board User’s Manual Ver. 1.
Contents Notices ...........................................................................................................v Safety information .........................................................................................vi About this guide ............................................................................................ vii How this guide is organized ............................................................. vii Where to find more information .....................................
Contents 1.8.5 1.9 1.10 PCI Express x16 .......................................................... 1-21 Jumpers ....................................................................................... 1-22 Connectors .................................................................................. 1-23 1.10.1 Rear panel connectors ................................................. 1-23 1.10.2 Internal connectors ....................................................... 1-25 Chapter 2: BIOS setup 2.
Contents 2.6 2.7 iv 2.5.3 ACPI 2.0 Support [No] ...................................................2-19 2.5.4 ACPI APIC Support [Enabled] .......................................2-19 2.5.5 APM Configuration ....................................................... 2-20 2.5.6 Hardware Monitor ......................................................... 2-22 2.5.7 Energy Lake Feature [Enabled] .................................... 2-23 Boot menu...........................................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. This chapter also lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Typography Bold text Indicates a menu or an item to select Italics Used to emphasize a word or a phrase Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key Example: means that you must press the Enter or Return key ++ If you must press two or more keys simultaneously, the key names are linked with a plus sign (+) Command Example: ++ Means that you must type the command exactly as shown, then supply the require
AIMB-562 specifications summary CPU LGA775 socket for Intel® Core® 2 Duo / Pentium® D / Pentium® 4 / Celeron® processor Compatible with the Intel® 05B/05A and 04B/ 04A processors Supports Intel® Enhanced Memory 64 Technology (EM64T) Supports Enhanced Intel® SpeedStep® Technology (EIST) Supports Intel® Hyper-Threading Technology Chipset Northbridge: Intel® 945G Southbridge: Intel® ICH7 Front Side Bus 1066/800/533 MHz Memory Dual-channel memory architecture 4 x 240-pin DIMM sockets support up to 4GB of
AIMB-562 specifications summary BIOS features 4 Mb Flash ROM, AMI BIOS, PnP, WfM2.0, DMI2.0, SM BIOS 2.3 Industry standard PCI 2.2, USB 2.0 Manageability WfM 2.0, DMI 2.0, WOL by PME, WOR by PME, Chassis Intrusion Internal connectors 2 x USB 2.0 connectors for 4 additional USB 2.
This chapter describes the motherboard features and the new technologies it supports.
1.1 Welcome! Thank you for buying an ® AIMB-562 motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
Dual-core processors contain two physical CPU cores with dedicated L2 caches to meet demands for more powerful processing. Intel®’s 65nm process is the most advanced chip manufacturing technology, delivering breakthrough performance, enhanced media experience, and low power consumption. Intel ® 65nm dual-core processors utilize the latest package technologies for a thinner, lighter design without compromising performance.
PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus. PCI Express features point-to -point serial interconnections between devices and allows higher clockspeeds by carrying data in packets. This high speed interface is software compatible with existing PCI specifications. See page 1-22 for details.
1.4 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity • Hold components by the edges to avoid touching the ICs on them.
1.5 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 1.5.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
1.5.
1.6 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package. 1.6.1 • Your boxed Intel® Pentium® 4 LGA775 processor package should come with installation instructions for the CPU, fan and heatsink assembly. If the instructions in this section do not match the CPU documentation, follow the latter.
2. Press the load lever with your thumb (A) and move it to the left (B) until it is released from the retention tab. Retention tab PnP Cap A Load lever B This side of the cam box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! The motherboard supports Intel ® Pentium ® D or Intel ® Pentium ® 4 LGA775 processors with the Intel ® Enhanced Memory 64 Technology (EM64T), Enhanced Intel SpeedStep ® Technology (EIST), and Hyper-Threading Technology.
1.6.2 Installing the CPU heatsink and fan ® The Intel Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • Install the motherboard to the chassis before you install the CPU fan and heatsink assembly • When you buy a boxed Intel ® Pentium ® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel® -certified multi-directional heatsink and fan.
2. 3. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A B A A B When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU fan connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
1.6.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
4. Remove the heatsink and fan assembly from the motherboard. 5. Rotate each fastener clockwise to reset the orientation. Narrow end of the groove The narrow end of the groove should point outward af ter reset ting. ( The photo shows the groove shaded for emphasis.
1.7 System memory 1.7.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
• A lways install DIM Ms with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor. Refer to the memory Qualified Vendors List on the next page for details. • Due to CPU limitation, DIMM modules with 128 Mb memory chips or doublesided x16 memory chips are not supported in this motherboard. When using one DDR DIMM module, install into DIMM_B1 slot only. • 1.7.
DDR2 667 Qualified Vendors List Size Vendor 512MB 1024MB 512MB 256MB 256MB 512MB 256MB 1024MB 256MB 512MB 1024MB Hynix Hynix Hynix MICRON MICRON Infineon Infineon Infineon ELPIDA ELPIDA ELPIDA Model HYMP564U64AP8-Y5 HYMP512U64AP8-Y4 HYMP564U64AP8-Y4 MT8HTF3264AY-667B5 MT8HTF3264AY-667B6 HYS64T64000HU-3S-A HYS64T32000HU-3S-A HYS64T128020HU-3S-A EBE25UC8ABFA-6E-E EBE51UD8AEFA-6E-E EBE11UD8AEFA-6E-E Side(s): SS - Single Sided Brand Hynix Hynix Hynix MICRON MICRON Infineon Infineon Infineon ELPIDA ELPIDA N/A Si
1.7.4 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by p r e s s i n g t h e r et a i n i n g c li p s outward. 2. A li gn a D I M M on t he s o c ket such that the notch on the DIMM matches the break on the socket. 3.
1.8 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion c ards. Failure to do so may c ause you physic al injur y and damage motherboard components. 1.8.1 Installing an expansion card To install an expansion card: 1.
1.8.
1.8.4 PCI slots The PCI slots support cards such as a L AN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows the type of LAN card that can be installed on a PCI slot. 1.8.6 1.8.5 PCI Express x16 This motherboard supports one PCI Express x16 graphics card. The figure shows a typical graphics card that can be installed on the PCI Express x16 slot.
1.9 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) R AM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
1.10 Connectors 1.10.1 Rear panel connectors 1 2 3 4 5 6 7 8 12 13 14 11 10 9 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 3. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
8. Microphone port (pink). This port connects a microphone. 9. Center/Subwoofer port (gray). This port connects the center/subwoofer speakers. Refer to the audio configuration table below for the function of the audio ports in 2, 4, 6, or 8-channel configuration.
1.10.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
PRI_IDE NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.
3. ITE IDE connector (40-1 pin PRI_EIDE [red]) Supported by the ITE8211F controller, this connector is for Ultra ATA 133/100/66 signal cables. This connector supports two IDE hard disk drives for easier data storage. PRI_EIDE PIN 1 PRI_EIDE connector 4. NOTE: Orient the red markings (usually zigzag) on the IDE cable to PIN 1.
5. Speaker connector (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. SPEAKER +5V GND GND Speak Out 1 Speaker out connector 6. CPU, Power and Chassis fan connectors (4-pin CPU_FAN, 3-pin PWR_RAN, 3-pin CHA_FAN) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V.
7. Digital Audio connector (4-1 pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. SPDIFOUT GND +5V SPDIF_OUT Digital audio connector The S/PDIF out module is purchased separately. 8. Power LED connector (3-pin PLED) This 3-pin connector is for the system power LED.
9. ATX power connectors (24-pin EATXPWR and 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot. • Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices.
10. Optical drive audio connector (4-pin CD) This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. CD Right Audio Channel Ground Ground Left Audio Channel CD audio connector Enable the CD - IN function in the audio utilit y when using this connector. 11. USB connectors (10-1 pin USB56, USB78) AIMB-562 USB78 1 USB+5V USB_P7USB_P7+ GND USB 2.
12. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC’97 audio standard.
14. System panel connector (10-1 pin F_PANEL) This connector supports several chassis-mounted functions. F_PANEL PWRSW PWRLED GND PWR PWR_LEDPWR_LED+ Reset Ground IDE_LEDIDE_LED+ RESET IDE LED * Requires an ATX power supply. System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details. • Power/Soft-off button (Black 2-pin PWRSW) This connector is for the system power button.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2.1 Managing and updating your BIOS 2.1.1 Creating a bootable floppy disk 1. Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1.44MB floppy disk into the drive. b. At the DOS prompt, type format A:/S then press . Windows® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click Start from the Windows® desktop, then select My Computer. c. Select the 3 1/2 Floppy Drive icon. d. Click File from the menu, then select Format.
2.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “2.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
2.2.1 BIOS menu screen Menu items Menu bar Configuration fields System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [ 1 1 : 5 1 : 1 9 [Thu 05/07/2004 [1.44M, 3.5 in] : [ S T 3 2 0 4 1 3 A :[Not Detected :[Not Detected :[Not Detected :[Not Detected :[Not Detected] General help ] ] ] ] ] ] ] Use [ ENTER ] , [ TA B ] or [SHIFT-TAB] to select a field.
2.2.4 Menu items T he hi ghli ghte d item o n t he m enu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 2.2.5 Main menu items Sub-menu items A solid triangle before each item on any menu screen means that the iteam has a sub-menu. To display the sub-menu, select the item and press . 2.2.
2.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [ 1 1 : 5 1 : 1 9 [Thu 05/07/2004 [1.44M, 3.
2.3.4 Primary, Third and Fourth IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information. Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA SMART Monitoring Type LBA/Large Mode Block(Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer : Hard Disk : ST320413A : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
Enhanced Mode Support On [S-ATA] The default setting S-ATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports only if you did not install any Serial ATA device. The P-ATA+S-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting S-ATA.
2.3.6 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version Build Date Processor Type Speed Count System Memory Size Appropriated Available : 0128 : 05/11/05 : Genuine Intel(R) CPU 3.
2.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. JumperFree Configuration USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP 2.4.
The following item appears only when you set the AI Overclocking item to [Manual]. CPU Frequency [XXX] Displays the frequency sent by the clock generator to the system bus and PCI bus. The value of this item is auto-detected by the BIOS. Use the <+> and <-> keys to adjust the CPU frequency. You can also type the desired CPU frequency using the numeric keypad. The values range from 100 to 400. Refer to the table below for the correct Front Side Bus and CPU External Frequency settings.
MCH Chipset Voltage [Auto] Allows you to select the memor y controller hub (MCH) voltage. Configuration options: [Auto] [1.50V] [1.60V] [1.70V] CPU VCore Voltage [Auto] Sets the operating VCore voltage. Conf iguration options: [Auto] [1.7000V] [1.6875V] [1.6750V] [1.6625V] [1.6500V] [1.6375V] [1.6250V] [1.6125V] [1.6000V] [1.5875V] [1.5750V] [1.5625V] [1.5500V] [1.5375V] [1.5250V] [1.5125V] [1.5000V] [1.4875V] [1.4750V] [1.4625V] [1.4500V] [1.4375V] [1.4250V] [1.4125V] [1.4000V] [1.3875V] [1.3750V] [1.
2.4.2 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options. USB Configuration Module Version - 2.23.0-F.4 USB Devices Enabled: None USB Function Legacy USB Support USB 2.0 Controller USB 2.0 Controller Mode BIOS EHCI Hand-Off [Enabled] [Auto] [Enabled] [HiSpeed] [Disabled] T h e M o d u l e Ve r s i o n a n d U S B D e v i c e s E n a b l e d i t e m s s h o w t h e auto-detected values.
2.4.3 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu. Advanced Chipset Settings Configure DRAM Timing by SPD [Enabled] Booting Graphic Adapter Priori Internal Graphics Mode Select [PCI Express/Int-VG] [Enabled, 8MB] Graphics memory type [Auto] Advanced Chipset Settings Booting Graphic Adapter Priority [PCI Express/Int-VGA] Allows selection of the graphics controller to use as primar y boot devic e.
2.4.4 Onboard Devices Configuration Configure Win627EHG Super IO Chipset Quick Resume Technology HD Audio Controller Front Panel Support Type Onboard PCIEX GbE LAN LAN Option ROM ITE8211F Controller Detecting Device Time [Enabled] [Enabled] [AC97] [Enabled] [Disabled] [Enabled] [Quick Mode] Serial Port1 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ [3F8/IRQ4] [378] [ECP] [DMA3] [IRQ7] HD Audio Controller [Enabled] Enables or disables the Azalia/AC’97 CODEC.
Parallel Port Address [378] Allows you to select the Parallel Port base addresses. Configuration options: [Disabled] [378] [278] [3BC] Parallel Port Mode [ECP] Allows you to select the Parallel Port mode. Configuration options: [Normal] [Bi-directional] [EPP] [ECP] ECP Mode DMA Channel [DMA3] Appears only when the Parallel Port Mode is set to [ECP]. This item allows you to set the Parallel Port ECP DMA. Configuration options: [DMA0] [DMA1] [DMA3] EPP Version [1.
2.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [PCI Device] [Reserved] 2.5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press to display the configuration options. Suspend Mode Repost Video on S3 Resume ACPI 2.
2.5.5 APM Configuration APM Configuration Power Button Mode [On/Off] Restore on AC Power Loss Power On By RTC Alarm Power On By External Modems Power On By PCI Devices Power On By PCIE Devices [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed.
Power On By PCI Devices [Disabled] When set to [ Enabled], this parameter allows you to turn on the system through a PCI L AN or modem card. This feature requires a n AT X p o w e r s u p p l y t h a t p r ov i d e s a t l e a s t 1A o n t h e + 5 VS B l e a d. Configuration options: [Disabled] [Enabled] Power On By PCIE Devices [Disabled] When set to [ Enabled], this parameter allows you to turn on the system through a PCI Express L AN card.
2.5.6 Hardware Monitor Hardware Monitor CPU Temperature MB Temperature [51ºC/122.5ºF] [41ºC/105.5ºF] CPU Fan Speed (RPM) CPU Q-Fan Control Chassis Fan Speed (RPM) Power Fan Speed (RPM) [3813 RPM] [Disabled] [N/A] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.320V] [ 3.345V] [ 5.094V] [11.880V] C P U T e m p e r a t u r e MB Temperature [xxxC/xxxF] [ x x x C / x x x F ] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. 2.5.7 Energy Lake Feature [Enabled] Allows you to enable or disable the Energy Lake technology feature.
2.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Boot Settings Boot Device Priority Boot Settings Configuration Security 2.6.1 Boot Device Priority Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [PM-ST330620A] [PS-ADVANSUS CD-S360] 1st ~ xxth Boot Device [1st Floppy Drive] These items specif y the boot device priority sequence from the ava i l a b l e d ev i c e s .
2.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 2.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Security Settings Supervisor Password User Password : Not Installed : Not Installed to change password. again to disabled password.
After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check [Full Access] [Setup] User Access Level (Full Access] This item allows you to select the access restriction to the Setup items.
Password Check [Setup] When set to [Setup], BIOS checks for user password when a c c e s s i n g t h e S et u p u t i l i t y. W h e n s et t o [ A l way s ] , B I O S c h e c ks f o r us e r pas swo r d b ot h w hen ac c e s sin g S et up an d b o ot in g t he syste m. Configuration options: [Setup] [Always] 2.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System Time, and Password, the BIOS asks for a confirmation before exiting. Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select Ok to discard any changes and load the previously saved values.
