NAN XL 72" & 90" INDUSTRIAL FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz For Damp Location QUICK ASSEMBLY NOTES: * Do not wire in fan while house wires are Live. Turn power off at breaker before installation begins. * Do not use any controls, wall or remote, other than those provided by Matthews Fan Company. * Please do not use any electric or battery powered tools in the assembly and installation of this or any other Matthews Fan Company product.
TABLE OF CONTENTS 1. Tools and Materials Required......................................................................................1 2. Package Contents ...................................................................................................... 1 3. Safety Rules................................................................................................................ 2 4. Mounting Options.....................................................................................................
1. TOOLS AND MATERIALS REQUIRED Philips screwdriver Blade screwdriver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS c Unpack your fan and check the contents. You should have the following items: a. b. c. d. e. f. g. Blade set (3) Hanger bracket assembly Ball / down rod assembly Coupling cover Fan motor assembly Hand held transmitter+holder+2 mounting screws Wall transmitter incl. 2 mounting screws and 3 wire nuts h. Wall plate incl. 1 face plate and 2 mounting screws i. 12V batteries (2) J.
3. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 9. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 3.
4. MOUNTING OPTIONS If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan 15.9 kgs (35lbs) or less. Do not use plastic outlet boxes.
5. HANGING THE FAN Ceiling hanger bracket REMEMBER to turn off the power. Follow the steps below to hang your fan properly. Ceiling canopy 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Fig. 5) 2. Remove the hanger bracket from the canopy by removing the 1 of 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head.
6. MAKE THE ELECTRIC CONNECTIONS Outlet box White ("AC IN N") NOTE: Your fan has included as standard equipment two types of controls: a hand held remote control and a wall mounted wall control. You may use both as long as the dip switches are calibrated the same. Select one of the controls at this moment for installation and programming of your fan. Green or bare copper (ground) Black ("AC IN L") Ground (green) (Connect to ground wire on hanger bracket if no house ground wire exists.
B. Wall mount remote control BLACK 1. Connect the fan supply (black) wire to the black household supply wire (Conductor cable between ceiling and wall outlet box). (Fig. 10) WHITE SUPPLY CIRCUIT a. Fan wire connection Ground Conductor Ceiling Outlet Box BLACK WHITE GREEN 2. Connect the neutral fan (white) wire to the white neutral household wire. 3. Connect the fan ground wire (green) to the household ground wire. 4. Check that the two plugs, large and small are making proper contact.
7. FINISHING THE INSTALLATION Outlet box Hanger bracket STANDARD CEILING INSTALLATION Screws 1. Tuck connections neatly into ceiling outlet box. Canopy 2. Slide the canopy up to hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 11) Canopy cover 3. Align the circular hole on canopy with the remaining hole on the hanger bracket, secure by tightening the two set screws.
9. PROGRAMMING YOUR FAN AND OPERATING THE REMOTE CONTROL AND WALL CONTROL Before programming takes place, fan must be fully assembled and mounted to the ceiling with blades attached. You must also choose which control you will be using for programming the fan, the remote or the wall control. No other wall control should be used with this fan but that whichwas included. Using another wall control other than ours will damage your fan and void your warranty.
NOTE: If the self calibration test failed, turn the AC power off; restore power and process the self calibration test again. NOTE: During self calibration test, the remote and the wall control are non-functional. NOTE: The learning frequency function and calibration test will continue to retain the last frequency and calibration set even when the power is shut off. If the frequency is changed self calibration test will occur again.
11. CARE OF YOUR FAN Here are some suggestions to help you maintain your fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish.
LIMITED LIFETIME WARRANTY MATTHEWS-GERBAR, LTD. DBA MATTHEWS FAN COMPANY LIFETIME LIMITED WARRANTY. warranted by Matthews-Gerbar, Ltd. to the original user against defects in workmanship or materials under normal use and inside or outside damp location installation for: Motors: Lifetime of original purchaser: Labor & Component parts: (lights, finish, blades, etc…): one year after date of purchase, Light Bulbs: no warranty. Any part, which is determined by Matthews-Gerbar, Ltd.
