CA92276-8158 EN-09 ECONEL 100 S2 ／ TX120 ／ TX150 S6 ／ TX300 S4 ／ RX100 S5 ／ RX200 S4 ／ RX300 S4 ／ RX600 S4 Manual OS Installation
Manual OS Installation Before Reading This Manual Before Reading This Manual Remarks ■ Symbols Symbols used in this manual have the following meanings: These sections explain prohibited actions and points to note when using this software. Make sure to read these sections. These sections explain information needed to operate the hardware and software properly. Make sure to read these sections. ■ Key descriptions / operations Keys are represented throughout this manual in the following manner: E.g.
Manual OS Installation ■ Before Reading This Manual Abbreviations The following expressions and abbreviations are used throughout this manual.
Contents Chapter 1 Installing Windows Server 2003 ................................... 5 1.1 1.1.1 1.1.2 1.1.3 1.1.4 1.2 Preparation .......................................................................................... 6 Creating Driver Disk .................................................................................. Configuring Array ...................................................................................... Cautions for unconfigured array.............................................
Chapter 1 Installing Windows Server 2003 This chapter explains how to install Windows Server 2003 manually. 1.1 1.
Manual OS Installation 1.1 Chapter1 Installing Windows Server 2003 Preparation This section explains preparation requirements for installation. 1.1.1 Creating Driver Disk When installing the OS manually, it is necessary to create a driver installation disk beforehand. Create a driver disk by using PRIMERGY Startup Disc supplied with the server. About the procedure for creating a driver disk, refer to "User's Guide".
Manual OS Installation Chapter1 Installing Windows Server 2003 ● PRIMERGY RX100 S5 Onboard LAN / Expansion card Driver Onboard LAN Onboard LAN Driver & Broadcom Advanced Control Suite for Windows 2003 V12.2.0.2/V12.2.9.0 LAN card (PG-2861L / PG-289L / PG-288L/ PG285L) Onboard/PG-18xx/PG-28xx LAN Driver V13.4 SCSI card (PG-2281L) PG-2281L SCSI Driver for Windows 2003 / R2 V7.0.0.
Manual OS Installation Chapter1 Installing Windows Server 2003 ● PRIMERGY TX300 S4 Onboard LAN / Expansion card Driver Onboard LAN Onboard LAN Driver & Broadcom Advanced Control Suite for Windows 2003/2008 V4.8.5/V11.7.5 LAN card (PG-1853 / PG-1863 / PG-1882 / PG-1892/ Onboard/PG-18xx/PG-28xx LAN Driver V13.
Manual OS Installation Chapter1 Installing Windows Server 2003 1.1.2 Configuring Array When you operate with array configurations, configure arrays first before you install OS. 1 Turn on the server. 2 Configure an array. The method differs depending on your array controller. For Onboard Software RAID (Embedded MegaRAID SATA) When the following message appears, press the [Ctrl] + [M] keys or the [Enter] key. Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.
Manual OS Installation Chapter1 Installing Windows Server 2003 1.1.4 Installing Internal Options Before starting installation of the OS, install internal options in the server. For the procedures, refer to "Chapter 6 Installing Internal Options" in the "User's Guide". When the following optional devices are connected to the server, be sure to read "Precautions on OS Installation" described below. Failure to observe the cautions may cause the OS to be installed in unexpected media.
Manual OS Installation 1.2 Chapter1 Installing Windows Server 2003 Installation Procedure This section explains how to install Windows Server 2003/Windows Server 2003 x64/Windows Server SBS 2003 manually. For details on the OS settings, refer to the following website. http://technet.microsoft.com/en-us/library/bb123872(EXCHG.65).aspx ◆ For using the external Floppy Disk, connect the USB connector to the server before turning on the power.
Manual OS Installation Chapter1 Installing Windows Server 2003 3 Select the following depending on your controller type, and press the [Enter] key.
Manual OS Installation Chapter1 Installing Windows Server 2003 When the ServerStart window appears, exit ServerStart. 2 Execute the following command on the PRIMERGY Startup Disc. For PRIMERGY ECONEL 100 S2 [CD/DVD drive]:\DRIVERS\VIDEO\ATI\W2K3\Setup.exe For PRIMERGY RX100 S5/TX150 S6 [CD/DVD drive]:\DRIVERS\VIDEO\MATROX\w2k3\ServerEnginesG200eSETUP.exe or \DRIVERS\VIDEO\MATROX\w2k3x64\ServerEnginesG200eSETUP.
Manual OS Installation Chapter1 Installing Windows Server 2003 10 Apply Windows Server 2003 (or Windows Server 2003 x64) Service Pack. For details, refer to the descriptions on the window. When applying the Service Pack, a driver may be replaced with the driver in the Service Pack. For more information, refer to the manual supplied with hardware. 11 Install ServerView ServerView download is available at the Fujitsu PRIMERGY Website. http://www.fujitsu.
Chapter 2 Installing Windows Server 2008 This chapter explains how to install Windows Server 2008 manually. For the Server Core installation, refer to Chapter 3 2.1 2.2 Preparation Installation Procedure * For the latest information on Windows Server 2008 support, refer to the matrix provided at: http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf * For some models, the software attached with the server does not support Windows Server 2008.
Manual OS Installation 2.1 Chapter2 Installing Windows Server 2008 Preparation This section explains preparation requirements for installation. 2.1.1 Creating Driver Disk When installing the OS manually, it is necessary to create a driver installation disk beforehand. There is a 2-type procedure for creating the driver disk by using PRIMERGY Startup Disc supplied with the server and by downloading from webpage.
Manual OS Installation Chapter2 Installing Windows Server 2008 ● PRIMERGY RX100 S5 Onboard LAN / Expansion card Driver Intel Chipset driver Intel Chipset Driver for Windows Server 2008 Onboard LAN Onboard LAN Driver & Broadcom Advanced Control Suite for Windows 2008/2008 R2 V12.2.0.3/V12.2.9.0 LAN card (PG-2861L / PG-289L / PG288L/ PG-285L) Onboard / PG-18xx/28xx LAN Driver V13.4 SCSI card (PG-2281L) PG-2281L SCSI Driver for Windows 2008 / R2 x64 Edition V7.2.0.
Manual OS Installation Chapter2 Onboard LAN / Expansion card Installing Windows Server 2008 Driver SAS array controller card(PG-248B / PG- MegaRAID SAS Windows Server 2008 Drivers Disk 248C / PG-244C1) or MegaRAID SAS Windows Server 2008 for x64 Edition Drivers Disk Fibre Channel card (PG-FC202) PG-FC202 Storport Miniport Driver V2.01a4 for Windows 2008 SAS Ctrl (PG-228BL) Install it from PCI-Express SAS Card Document & Tool CD.
Manual OS Installation Chapter2 Installing Windows Server 2008 Onboard LAN / Expansion card Driver SAS Ctrl (PG-224B/PG-228B) Install it from PCI-Express SAS Card Document & Tool CD. Other expansion card Driver attached with each expansion card 2.1.2 Configuring Array When you operate with array configurations, configure arrays first before you install OS. 1 Turn on the server. 2 Configure an array. The method differs depending on your array controller.
Manual OS Installation Chapter2 Installing Windows Server 2008 2.1.4 Installing Internal Options Before starting installation of the OS, install internal options in the server. For the procedures, refer to "Chapter 6 Installing Internal Options" in the "User's Guide". When the following optional devices are connected to the server, be sure to read "■Precautions on OS Installation" described below. Failure to observe the cautions may cause the OS to be installed in unexpected media.
Manual OS Installation Chapter2 Installing Windows Server 2008 When installation of OS has been completed, install extension I/O riser card and make the LAN port on a card effective once again. 1 Start up the BIOS Setup Utility. 2 Select a "Peripheral Configuration sub menu" from a "Advanced menu",and press the [Enter] key. 3 Change [IO-Riser LAN Controller] from "Disabled" to "Enabled". 4 Save a setup by [F10] key and then exit BIOS Setup Utility.
Manual OS Installation 2.2 Chapter2 Installing Windows Server 2008 Installation Procedure This section explains how to install Windows Server 2008 manually. ■ Requirements • • • 1 Windows Server 2003 CD/DVD (installation disc) PRIMERGY Startup Disc (supplied with the server) A driver disk created in advance Prepare the installation disc for Windows Server 2008. Turn on the server, and immediately insert the Windows Server 2008 DVD-ROM (*1) into the CD/DVD drive.
Manual OS Installation Chapter2 Installing Windows Server 2008 For Onboard Software RAID (Embedded MegaRAID SATA) 1 Set the driver floppy disk when the wizard window below is displayed. 2 Click [Browse], and select the folder in which the installed driver is saved 3 After selecting the driver, the following message is displayed. LSI Embedded MegaRAID (A:\MegaSR1.INF) 4 Click [Next] and go on to the step 4 on page 28.
Manual OS Installation Chapter2 Installing Windows Server 2008 1 When the wizard window is displayed as below, click the "Load Driver", go on to the driver installation window. 2 At the display below, change the Windows installation DVD to Array Controller Document & Tool CD. Then click the [Browse]. 3 Select the folder in which the installed driver is saved. 4 Select the folder at the following location, and click [OK].
Manual OS Installation Chapter2 Installing Windows Server 2008 5 Select the following driver, and click [Next]. For Windows Server 2008 Standard/Enterprise (32-bit) RAID 5/6 SAS based on LSI MegaRAID ([CD/DVD drive]:\Drivers\Mega-SAS\W2K8\oemsetup.inf) For Windows Server 2008 Standard/Enterprise (64-bit) RAID 5/6 SAS based on LSI MegaRAID ([CD/DVD drive]:\Drivers\Mega-SAS\W2K8x64\oemsetup.inf) 6 Change the disc to Windows installation DVD again, and go on to the step 4 on page 28.
Manual OS Installation Chapter2 Installing Windows Server 2008 For SAS controller card or onboard IM (Integrated Mirroring SAS) 1 When the wizard window is displayed as below, click the "Load Driver", go on to the driver installation window. 2 At the display below, change the Windows installation DVD to Array Controller Document & Tool CD. Then click the [Browse]. 3 Select the folder in which the installed driver is saved. Select the folder at the following location, and click [OK].
Manual OS Installation Chapter2 Installing Windows Server 2008 [CD/DVD drive]:\Drivers\IM-SAS\W2K8x64 4 Select the following driver, and click [Next]. For Windows Server 2008 Standard/Enterprise (32-bit) LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort ([CD/DVD drive]:\Drivers\IM-SAS\W2K8\lsi_sas.inf) For Windows Server 2008 Standard/Enterprise (64-bit) LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort ([CD/DVD drive]:\Drivers\IM-SAS\W2K8x64\lsi_sas.
Manual OS Installation Chapter2 Installing Windows Server 2008 For Unconfigured array No manual driver installation is required. Go on to the step 4 on page 28. 4 Select OS installation type. Select "Windows Server 2008 Enterprise (Full Installation)" and click [Next]. 5 When the following window appears, read the license terms and put a check-mark to agree. Then click [Next]. The program automatically executes the OS installation.(The system is rebooted a couple of times.
Manual OS Installation 6 Chapter2 Installing Windows Server 2008 Install the LAN driver. Install it according to an attached manual after having downloaded the latest LAN driver in the following Web. http://www.fujitsu.com/global/services/computing/server/ia/driver/index.html The name of Onboard LAN that displays it with the device manager is the following.
Manual OS Installation Chapter2 Installing Windows Server 2008 8 Restart the server. VGA chip installation for PRIMERGY ECONEL 100 S2 cannot be executed via installer. VGA chip from ATI needs a driver different from other servers. Thus, the driver is not supplied with the Startup Disc. Please download the required driver from the Web page. For PRIMERGY RX100 S5 / PRIMERGY TX150 S6 / PRIMERGY RX200 S4 / PRIMERGY TX300 S4 / PRIMERGY RX300 S4 Double click "install_kronos2_vga.
Manual OS Installation Chapter2 Installing Windows Server 2008 For PRIMERGY RX600 S4 Execute the following file stored on the PRIMERGY Startup Disc, and apply the hot fix module. For Windows Server 2008(32-bit) [CD/DVD drive]: \Hotfix\Essential\W2K8\Windows6.0-KB956115-x86.msu \Hotfix\Essential\W2K8\Windows6.0-KB955252-x86.msu \Hotfix\Essential\W2K8\Windows6.0-KB954429-x86.msu For Windows Server 2008(64-bit) [CD/DVD drive]: \Hotfix\Essential\W2K8x64\Windows6.0-KB956115-x64.
Chapter 3 Installing Windows Server 2008 Server Core This chapter explains how to install Server Core manually. 3.1 3.2 Preparation Installation Procedure * For the latest information on Windows Server 2008 support, refer to the matrix provided at: http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf * For some models, the software attached with the server does not support Windows Server 2008.
Manual OS Installation 3.1 Chapter3 Installing Windows Server 2008 Server Core Preparation This section explains required preparation for installation. 3.1.1 Creating Driver Disk When installing the OS manually, it is necessary to create a driver installation disk beforehand. There is a 2-type procedure for creating the driver disk by using PRIMERGY Startup Disc supplied with the server and by downloading from webpage.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core ● PRIMERGY RX100 S5 Onboard LAN / Expansion card Driver Intel Chipset driver Intel Chipset Driver for Windows Server 2008 Onboard LAN Onboard LAN Driver & Broadcom Advanced Control Suite for Windows 2008/2008 R2 V12.2.0.3/V12.2.9.0 LAN card (PG-2861L / PG-289L / PG288L/ PG-285L) Onboard / PG-18xx/28xx LAN Driver V13.4 SCSI card (PG-2281L) PG-2281L SCSI Driver for Windows 2008 / R2 x64 Edition V7.2.0.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core Onboard LAN / Expansion card Driver SAS array controller card(PG-248B / PG- MegaRAID SAS Windows Server 2008 Drivers Disk 248C / PG-244C1) or MegaRAID SAS Windows Server 2008 for x64 Edition Drivers Disk SCSI card (PG-2281L) PG-2281L SCSI Driver for Windows 2008 / R2 x64 Edition V7.0.0.6 Fibre Channel card (PG-FC202) PG-FC202 Storport Miniport Driver Core Kit V2.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core Onboard LAN / Expansion card Driver SCSI card (PG-2281) PG-2281 SCSI Driver for Windows 2008 / R2 x64 Edition V7.0.0.6 Fibre Channel card (PG-FC202) PG-FC202 Storport Miniport Driver Core Kit V2.01a4 for Windows 2008 Display driver Onboard VIDEO Driver for Windows 2008/2008 x64 SAS Ctrl (PG-224B/PG-228B) Install it from PCI-Express SAS Card Document & Tool CD.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core 3.1.4 Installing Internal Options Before starting installation of the OS, install internal options in the server. For the procedures, refer to "Chapter 6 Installing Internal Options" in the "User's Guide". When the following optional devices are connected to the server, be sure to read "■Precautions on OS Installation" described below. Failure to observe the cautions may cause the OS to be installed in unexpected media.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core When installation of OS has been completed, install extension I/O riser card and make the LAN port on a card effective once again. 1 Start up the BIOS Setup Utility. 2 Select a "Peripheral Configuration sub menu" from a "Advanced menu",and press the [Enter] key. 3 Change [IO-Riser LAN Controller] from "Disabled" to "Enabled". 4 Save a setup by [F10] key and then exit BIOS Setup Utility.
Manual OS Installation 3.2 Chapter3 Installing Windows Server 2008 Server Core Installation Procedure This section explains how to install Windows Server 2008 Server Core manually. ■ Requirements • • • 1 Windows Server 2003 CD/DVD (installation disc) PRIMERGY Startup Disc (supplied with the server) A driver disk created in advance Prepare the installation disc for Windows Server 2008. Turn on the server, and immediately insert the Windows Server 2008 DVD-ROM (*1) into the CD/DVD drive.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core For Onboard Software RAID (Embedded MegaRAID SATA) 1 Set the driver floppy disk when the wizard window below is displayed. 2 Click [Browse], and select the folder in which the installed driver is saved 3 After selecting the driver, the following message is displayed. LSI Embedded MegaRAID (A:\MegaSR1.INF) 4 Click [Next] and go on to the step 4 on page 45.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core For SAS array controller card (MegaRAID SAS) 1 When the wizard window is displayed as below, click the "Load Driver", go on to the driver installation window. 2 At the display below, change the Windows installation DVD to Array Controller Document & Tool CD. Then click the [Browse]. 3 Select the folder in which the installed driver is saved. 4 Select the folder at the following location, and click [OK].
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core 5 Select the following driver, and click [Next]. For Windows Server 2008 Standard/Enterprise (32-bit) RAID 5/6 SAS based on LSI MegaRAID ([CD/DVD drive]:\Drivers\Mega-SAS\W2K8\oemsetup.inf) For Windows Server 2008 Standard/Enterprise (64-bit) RAID 5/6 SAS based on LSI MegaRAID ([CD/DVD drive]:\Drivers\Mega-SAS\W2K8x64\oemsetup.inf) 6 Change the disc to Windows installation DVD again, and go on to the step 4 on page 45.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core For SAS controller card or onboard IM (Integrated Mirroring SAS) 1 When the wizard window is displayed as below, click the "Load Driver", go on to the driver installation window. 2 At the display below, change the Windows installation DVD to Array Controller Document & Tool CD. Then click the [Browse]. 3 Select the folder in which the installed driver is saved. Select the folder at the following location, and click [OK].
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core [CD/DVD drive]:\Drivers\IM-SAS\W2K8x64 4 Select the following driver, and click [Next]. For Windows Server 2008 Standard/Enterprise (32-bit) LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort ([CD/DVD drive]:\Drivers\IM-SAS\W2K8\lsi_sas.inf) For Windows Server 2008 Standard/Enterprise (64-bit) LSI Adapter, SAS 3000 series, 4-port with 1064E -StorPort ([CD/DVD drive]:\Drivers\IM-SAS\W2K8x64\lsi_sas.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core For Unconfigured array No manual driver installation is required. Go on to the step 4 on page 45. 4 Select OS installation type. Select "Windows Server 2008 Enterprise (Server Core Installation)" and click [Next]. 5 When the following window appears, read the license terms and put a check-mark to agree. Then click [Next]. The program automatically executes the OS installation.(The system is rebooted a couple of times.
Manual OS Installation 6 Chapter3 Installing Windows Server 2008 Server Core Install the LAN driver. Install it according to an attached manual after having downloaded the latest LAN driver in the following Web. http://www.fujitsu.com/global/services/computing/server/ia/driver/index.html 7 Install the Intel Chipset driver. For PRIMERGY ECONEL 100 S2 / PRIMERGY RX100 S5 / PRIMERGY TX150 S6 1 Insert the installation disc into the CD/DVD drive. 2 Execute commands below under Command Prompt.
Manual OS Installation Chapter3 Installing Windows Server 2008 Server Core For PRIMERGY RX600 S4 12 Make the registry editable, and adding the following registry key: Key:HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\PCI\Parametars value name:111d8018 value kind :REG_BINARY value data :00 00 10 00 00 00 00 00 For PRIMERGY RX600 S4 Execute the following file stored on the PRIMERGY Startup Disc, and apply the hot fix module.
Manual OS Installation Manual OS Installation CA92276-8158 EN-09 • • • Issued in November 2009 Issued by FUJITSU LIMITED The contents of this manual may be revised without prior notice. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
