COMMERCIAL SERIES TREADMILL OWNER’S MANUAL 06'_Treadmills_M.
06'_Treadmills_M.
TABLE OF CONTENTS CHAPTER 1: IMPORTANT SAFETY INSTRUCTIONS 1.1 1.2 1.3 1.4 1.5 PAGES Before Getting Started .................................................................................................... 01 Proper Usage ................................................................................................................. 01 Read and Save These Instructions ................................................................................... 01 Electrical Requirements ....................
06'_Treadmills_M.
CHAPTER 1: IMPORTANT SAFETY INSTRUCTIONS 1.1 BEFORE GETTING STARTED 1.3 BEFORE GETTING STARTED It is the sole responsibility of the purchaser of Matrix Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel, on proper usage of the equipment. This Treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating the MATRIX treadmill.
CHAPTER 1: IMPORTANT SAFETY INSTRUCTIONS CHAPTER 2: PREVENTATIVE MAINTENANCE 1.4 ELECTRICAL REQUIREMENTS 2.1 RECOMMENDED CLEANING TIPS For your safety and treadmill performance, the ground on this circuit must be non-looped. Please refer to NEC article 210-21 and 210-23. Your Treadmill is provided with a power cord with a plug listed below and requires the listed outlet. Any alterations of this power cord could void all warranties of this product. 1. Use a soft, clean cotton cloth.
CHAPTER 2: PREVENTATIVE MAINTENANCE 2.4 ADJUSTING THE BELT CHAPTER 3: SERIAL NUMBER LOCATION 3.1 MX-T3x & T3xi TREADMILL After placing the treadmill in the position it will be used, the belt must be checked for proper tension and centering. The belt might need to be adjusted after the first two hours of use. Temperature, humidity, and use cause the belt to stretch at different rates. If the belt starts to slip when a user is on it, be sure to follow the directions below.
CHAPTER 4: MX-T3X / MX-T3XI OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 4.1 MX-T3x CONSOLE DESCRIPTION MX-T3xi CONSOLE DESCRIPTION The MATRIX treadmill is inspected before it is packaged. It is shipped in four pieces: the base, the upright console supports, the handlebar and the console. Carefully unpack the unit and dispose of the box material. The MATRIX treadmill is inspected before it is packaged.
CHAPTER 4: MX-T3X / MX-T3XI OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 4.2 MANUAL OPERATION 4.4 HEART RATE CONTROL MATRIX design makes using the programs as easy as one touch of a button. Follow these easy Steps to enter into the Heart Rate Program. QUICK START Press the “QUICK START” key and the LED will show “3”, “2”, “1”, “GO!”. The treadmill will start running from the lowest incline and 0.5 mph, with the default time counting down from 20 minutes.
CHAPTER 4: MX-T3X / MX-T3XI OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 4.5 FIT TEST FIT TEST allows you to measure your fitness based on a program designed specifically for your Matrix Treadmill. The test takes 5 minutes and is based on your heart rate. User should keep hands on contact heart rate graps.
CHAPTER 4: MX-T3X / MX-T3XI OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 4.6 ENGINEERING MODE 4.7 MANAGER SCREEN DESCRIPTIONS / DETAILS Engineering screens allow the viewing and editing of variables that would be necessary for a club operator/manager to customize. Unless otherwise noted, engineering screens consist of the initial screen, the editing or action screen, and the saving screen. The initial screen displays the variable type, and in most cases, the current value.
CHAPTER 4: MX-T3X / MX-T3XI OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 4.7 MANAGER SCREEN DESCRIPTIONS / DETAILS PRODUCT TEST Test the product. Below is a list of the MX-T3xi functions for each engineering screen. Exceptions will be noted in the description for each engineering screens: P0 LOW SPEED LEARN MODE (EDIT) This variable controls the low limit for the speed of the treadmill. P1 HIGH SPEED LEARN MODE (EDIT) This variable controls the hight limit for the speed of the treadmill.
CHAPTER 5: MX-T5X OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 5.2 MANUAL OPERATION 5.1 CONSOLE DESCRIPTION MATRIX design makes using the programs as easy as one touch of a button. QUICK START Start pedaling and press QUICK START to begin workout. MANUAL MODE allows you to enter desired time, level and weight.
CHAPTER 5: MX-T5X OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 5.3 OPERATING LEVEL BASED PROGRAMS 5.4 HEART RATE CONTROL Your MATRIX treadmill offers versatile programs to keep the usere motivated. The following instructions will guide you through simple steps to select INTERVALS, ROLLING, and RANDOM programs. For your convenience, MATRIX Treadmills come standard with digital contact heat rate sensors and are POLAR telemetry compatible. STEP 1 Select the PROGRAM button on left of panel.
CHAPTER 5: MX-T5X OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE MEN’S OUTPUT TABLE FOR TEST #1 AND #2 AGE EXCELLENT GOOD 15-19 61+ 56 ~ 61 20-29 57+ FAIR POOR 52 ~57 48 ~ 51 42 - 44 ~ 51 38 ~ 43 38 - 30-39 51+ 48 ~ 51 40 ~ 47 34 ~ 39 34 - 40-49 48+ 44 ~ 48 36 ~ 43 30 ~ 35 30 - 50-59 44+ 40 ~ 44 32 ~ 39 60-69 21+ 21 ~ 26 27 ~ 35 36 ~ 40 40 - 70-79 36+ 32 ~ 36 23 ~ 31 17 ~ 22 17 - 52 ~ 57 AVERAGE 25 ~ 31 25 - 5.
CHAPTER 5: MX-T5X OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 5.6 ENGINEERING MODE 5.7 MANAGER SCREENS EXCEPTIONS/DETAILS Manager screens allow the viewing and editing of variables that would be necessary for a club operator/manager to customize. Unless otherwise noted manager screens consist of the initial screen, the editing or action screen and the saving screen. The initial screen displays the variable type and in most cases the current value.
CHAPTER 5: MX-T5X OVERLAY DESCRIPTION / PROGRAMING / ENGINEERING MODE 5.8 USING CSAFE P10 DEFAULT CHANNEL (EDIT) Controls the default channel for enterainment CSAFE compativle devices. This variable is editable. Numeric entry is active. P11 DEFAULT VOLUME (EDIT) Controls the default channel for enterainment CSAFE compativle devices. This variable is editable. Numeric entry is active. P13 SPEED MODE (EDIT) Changes from Standard (Miles) to Metric (kilometers).
CHAPTER 6: MX-T3X / T3XI TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 6.1 MX-T3X / MX-T3XI MODEL SPECIFICATIONS SPECIFICATIONS Foot Print Weight Max User Weight Belt Type Frame Construction Running Area Incline Range Speed Min. Speed Max. Motor Type Controller Cooling Fan Electrical Receptacle Electrical Plug Electrical Receptacle Electrical Plug Electrical Amps Electrical Amps Deck Wax inches = 85” x 34” x 55” cm = 216 x 87 x 140 350 lbs kg 400 lbs = 181 kg Habisat Steel 20” x 60” 0-15% 0.
CHAPTER 6: MX-T3X / T3XI TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 6.2 MX-T3X / MX-T3XI MODEL REQUIRED FASTENERS & ASSEMBLEY TOOLS QTY PART # SKETCH DESCRIPTION 8mm ALLEN WRENCH 01 10mm ALLEN WRENCH 01 #2 PHILLIPS SCREW DRIVER [ 4.5 x 50 ] 08 Z50 FLAT WASHER 30x2.0L 08 Z51 SOCKET HEAD CAP SCREW M10 x 25 04 Z52 SOCKET HEAD CAP SCREW M8 x 30 02 Z52 BUTTON HEAD MACHINE SCREW M5 x 12L MX-T3X / T3XI • TREADMILL 01 NOTES 15 06'_Treadmills_M.
CHAPTER 6: MX-T3X / T3XI TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 6.3 MX-T3X / MX-T3XI MODEL ASSEMBLY STEPS • ATTENTION After installation is completed, the treadmill will need to be calibrated by using the AUTO-CHECK function. If this is not done, the treadmill's speed and incline values may be incorrect and damage the treadmill. Do not stand on the belt when performing the AUTO-CHECK function.
CHAPTER 6: MX-T3X / T3XI TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 6.4 MX-T3X / MX-T3XI MODEL ASSEMBLY STEPS STEP 3 STEP 4 Z53 Z53 FINAL ASSEMBLY • • • • AUTO CHECK Press and hold both incline “UP” and speed “DOWN“ buttons simultaneously for 3 seconds .Then the “ENGINEERING MODE” is shown onto the console. Press the incline “UP” button to find the “AUTO CHECK” screen. Press the incline “START” button and then, the treadmill will run the auto check function automatically.
CHAPTER 7: MX-T5X TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 7.1 MX-T5X MODEL SPECIFICATIONS SPECIFICATIONS Product Name Foot Print 157.5 Weight TIME DISTANCE ELEVATION SPEED 1 3 2 4 MANUAL ROLLING 6 7 8 KEYPAD QUICK START SELECT CLEAR INTERVALS 5 PAUSE HOLD TO RESET 9 0 RANDOM FIT TEST TARGET HR Max User Weight Belt Type Frame Construction Running Area Incline Range Speed Min. Speed Max.
CHAPTER 7: MX-T5X TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 7.2 MX-T5X MODEL REQUIRED FASTENERS & ASSEMBLEY TOOLS QTY PART # SKETCH DESCRIPTION 01 5mm ALLEN WRENCH 01 ALLEN WRENCH [ #8 x 168 ] 01 ALLEN WRENCH [ #5 x 172 ] 01 #2 PHILLIPS SCREW DRIVER [ 4.5 x 50 ] C10 FLAT HEAD MACHINE SCREW (M8 x 20L) 08 C09 FLAT HEAD MACHINE SCREW (M8 x 25L) 06 C05 SOCKET HEAD CAP SCREW (M8 x 15L) 04 C24 BUTTON HEAD MACHINE SCREW M5 x 10L 02 Q28 END CAP 12.
CHAPTER 7: MX-T5X TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 7.
CHAPTER 7: MX-T5X TREADMILL SPECIFICATIONS, PARTS, AND ASSEMBLY GUIDES 7.
06'_Treadmills_M.
MATRIX FITNESS SYSTEMS CORP. 1610 L AND MARK DRIVE COTTAGE GROVE WI 53527 USA T O L L F R EE 866.693.4863 w w w. m a t r i x f i t n e s s . c o m FAX 608.839.8687 REV. 02 06'_Treadmills_M.
