U7xe U5x U3x R7xe R5x R3x H7xe H5x H3x CYCLES OWNER’S MANUAL MX_12_HUR3x_5x_7xe_OM_Rev1_3.
IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS Read this GUIDE before using the OWNER’S MANUAL. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this product. It is the responsibility of the owner to ensure that all users of this product are adequately informed of all warnings and precautions.
DANGER TO REDUCE THE RISK OF ELECTRICAL SHOCK: Always unplug the unit from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking off parts. CAUTION If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing. WARNING 4 • Use this exercise bike for its intended purpose as described in this manual.
CAUTION CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE. It is essential that your unit is used only indoors, in a climate controlled room. If your unit has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the unit is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.
DANGER Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. BASIC OPERATION WARNING Connect this exercise product to a properly grounded outlet only.
LOCATION OF THE EXERCISE BIKE UPRIGHT SEAT HEIGHT Place the unit on a level and stable surface away from direct sunlight. The intense UV light can cause discoloration on the plastics. Locate your unit in an area with cool temperatures and low humidity. Please leave a clear zone on both sides of the unit that is at least 24” (600 mm). This zone must be clear of any obstruction and provide the user a clear exit path from the machine.
PULSE GRIPS Place the palm of your hands directly on the grip pulse handlebars. Both hands must grip the bars for your heart rate to register. It takes 5 consecutive heart beats (15-20 seconds) for your heart rate to register. When gripping the pulse handlebars, do not grip tightly. Holding the grips tightly may elevate your blood pressure. Keep a loose, cupping hold. You may experience an erratic readout if consistently holding the grip pulse handlebars.
RECOMMENDED CLEANING TIPS CARE AND MAINTENANCE Preventative maintenance and daily cleaning will prolong the life and look of your equipment. WHAT KIND OF ROUTINE MAINTENANCE IS REQUIRED? We use sealed bearings throughout our bikes so lubrication is not needed. The most important maintenance step is to simply wipe your perspiration off the bike after each use. A Use a soft, clean cotton cloth. DO NOT use paper towels to clean surfaces on the treadmill. Paper towels are abrasive and can damage surfaces.
HYBRID CYCLE™ ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the bike could have frame parts that are not tightened and will seem loose and may cause irritating noises.
INCLUDED FASTENERS FASTENERS REFERENCE SKETCH DESCRIPTION QUANTITY PACKAGE COLOR Z11 BUTTON HEAD BOLT(M8x25L) 4 WHITE Z12 SPRING WASHER 4 WHITE Z13 BUTTON HEAD BOLT(M5x10L) 2 WHITE Z21 BUTTON HEAD BOLT(M8x20L) 8 BLACK Z22 FLAT WASHER 8 BLACK BUTTON HEAD BOLT(M8x25L) 2 BLUE Z41 BUTTON HEAD BOLT(M8x50L) 8 RED Z42 ARC WASHER 8 RED Z43 SPRING WASHER 8 RED Z51 BUTTON HEAD BOLT(M8x15L) 4 GREEN Z52 FLAT WASHER 4 GREEN Z53 SPRING WASHER 4 GREEN Z71 ADJUSTMENT FOO
ASSEMBLY STEP 1 ASSEMBLY STEP 2 BLACK HARDWARE BAG CONTENTS : Z22 x4 Z23 x4 8 Z22 FLAT WASHER 8 Z23 SPRING WASHER 8 Open BLACK HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on each side. AJ1 C Z22 x4 Z23 x4 BUTTON HEAD BOLT(M8x20L) A Z21 x4 AJ2 Z21 Attach the ADJUSTMENT FOOT. YELLOW HARDWARE BAG CONTENTS MX_12_HUR3x_5x_7xe_OM_Rev1_3.
ASSEMBLY STEP 3 RED HARDWARE BAG : ASSEMBLY STEP 4 GREEN HARDWARE BAG : A Z41 BUTTON HEAD BOLT(M8x50L) 8 Z51 BUTTON HEAD BOLT(M8x15L) 4 Z42 ARC WASHER 8 Z52 FLAT WASHER 4 Z43 SPRING WASHER 8 Z53 SPRING WASHER 4 C Z42 AD4 Q07 Z52 Z51 Z53 Z42 Z43 Z41 MX_12_HUR3x_5x_7xe_OM_Rev1_3.indd 22-23 Attach the GUIDE RAIL SET to the MAIN FRAME using 4 BOLTS (F), 4 SPRING WASHERS (E) and 4 FLAT WASHERS (D).
ASSEMBLY STEP 6 ASSEMBLY STEP 5 7XE / 5X CONSOLE ASSEMBLY A 7XE SHOWN CONSOLE SCREW P02 P20 B Slide the LOWER LINK ARM into the PEDAL ARM BRACKET. C Attach the LOWER LINK ARM to the PEDAL ARM BRACKET using 1 FLAT WASHER (R), 1 SPRING WASHER (Q) and 1 BOLT (P). P06 P11 D 3X CONSOLE ASSEMBLY Slide 1 FLAT WASHER (N), 1 WAVY WASHER (O) and another FLAT WASHER (N) onto the LOWER LINK ARM. BLUE HARDWARE BAG CONTENTS : 7XE SHOWN Z34 2 A Open HARDWARE BAG.
UPRIGHT CYCLE ASSEMBLY UPRIGHT BIKE C8000 WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the bike could have frame parts that are not tightened and will seem loose and may cause irritating noises.
Z32 SPRING WASHER 4 YELLOW Z33 FLAT WASHER 4 YELLOW Z34 HEX SOCKET HEAD CAP SCREW(M8x25L) 2 BLUE Z41 BUTTON HEAD HEX SOCKET CAP SCREW-CHROME PLATED(M8x20L) 4 RED PACKAGE COLOR Z42 FLAT WASHER-CHROME PLATED 4 RED INCLUDED FASTENERS FASTENERS REFERENCE 28 SKETCH DESCRIPTION AMOUNT Z11 BUTTON HEAD HEX SOCKET CAP SCREW(M8x25L) 4 WHITE Z43 SPRING WASHER-CHROME PLATED 4 RED Z12 SPRING WASHER 4 WHITE Z51 BUTTON HEAD HEX SOCKET CAP SCREW WITH NYLOC(M5x12L) 4 GREEN Z13 BUTT
ASSEMBLY STEP 1 ASSEMBLY STEP 2 BLACK HARDWARE BAG CONTENTS : Z22 Z23 RED HARDWARE BAG CONTENTS Z21 HEX SOCKET HEAD CAP SCREW(M8x20L) 8 Z41 BUTTON HEAD HEX SOCKET CAP SCREW-CHROME PLATED(M8x20L) 4 Z22 FLAT WASHER 8 Z42 FLAT WASHER-CHROME PLATED 4 Z23 SPRING WASHER 8 Z43 SPRING WASHER-CHROME PLATED 4 A Open BLACK HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on each side.
ASSEMBLY STEP 3 ASSEMBLY STEP 4 YELLOW HARDWARE BAG CONTENTS : BUTTON HEAD HEX SOCKET CAP SCREW W/NYLOC(M8x20L) 4 Z32 SPRING WASHER 4 Z33 FLAT WASHER 4 Open YELLOW HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on each side. G12 2 A 6 Z32 Z33 Z31 2 Z31 WHITE HARDWARE BAG : Z51 Z11 BUTTON HEAD HEX SOCKET 4 CAP SCREW (M8x25L) Z12 SPRING WASHER 4 Z13 BUTTON HEAD SCREW (M5x10L) 2 MX_12_HUR3x_5x_7xe_OM_Rev1_3.
ASSEMBLY STEP 5 CONSOLE SCREW 7XE / 5X CONSOLE ASSEMBLY BLUE HARDWARE BAG CONTENTS : 3X CONSOLE ASSEMBLY 7XE SHOWN Z34 HEX SOCKET HEAD CAP SCREW(M8x25L) 2 CONSOLE SCREW CONSOLE SCREW C22 A Open BLUE HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on Z34 C11 each side. C22 Z13 7XE SHOWN Z34 C11 ASSEMBLY COMPLETE! 34 MX_12_HUR3x_5x_7xe_OM_Rev1_3.
RECUMBENT CYCLE ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the bike could have frame parts that are not tightened and will seem loose and may cause irritating noises.
INCLUDED FASTENERS REFERENCE 38 SKETCH DESCRIPTION QUANTITY PACKAGE COLOR Z34 BUTTON HEAD BOLT(M8x25L) 2 BLUE Z41 BUTTON HEAD BOLT(M8x15L) 4 RED Z42 BUTTON HEAD BOLT(M8x50L) 4 RED Z43 ARC WASHER 4 RED Z44 SPRING WASHER 8 RED Z45 BUTTON HEAD BOLT(M8x15L) 3 RED Z71 ADJUSTMENT FOOT 1 Z55 BUTTON HEAD SCREW(M5x10L) 2 Z11 BUTTON HEAD BOLT(M8x25L) 4 WHITE Z12 SPRING WASHER 4 WHITE Z13 BUTTON HEAD BOLT(M5x10L) 2 WHITE Z21 BUTTON HEAD BOLT(M8x20L) 8 BLACK Z22 FLAT
ASSEMBLY STEP 1 ASSEMBLY STEP 2 BLACK HARDWARE BAG CONTENTS : Z22 Z23 Z21 Z22 Z23 Z21 BUTTON HEAD BOLT(M8x20L) 8 Z22 FLAT WASHER 8 Z23 SPRING WASHER 8 A Open BLACK HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on each side. C Attach the ADJUSTMENT FOOT. YELLOW HARDWARE BAG CONTENTS Z31 Z33 Z32 Z31 BUTTON HEAD BOLT(M8x15L) 4 Z32 FLAT WASHER 4 Z33 SPRING WASHER 4 A Open YELLOW HARDWARE BAG.
ASSEMBLY STEP 3 ASSEMBLY STEP 4 RED HARDWARE BAG CONTENTS : Z41 BUTTON HEAD BOLT(M8x15L) 4 Z42 BUTTON HEAD BOLT(M8x50L) 4 Z43 ARC WASHER 4 Z44 SPRING WASHER 8 Z45 BUTTON HEAD BOLT(M8x15L) 3 Z55 BUTTON HEAD SCREW(M5x10L) 2 A Open RED HARDWARE BAG. B Attach the STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 ARC WASHERS (C) on each side.
Z41 ASSEMBLY STEP 5 7XE / 5X CONSOLE ASSEMBLY 3X CONSOLE ASSEMBLY 7XE SHOWN A Attach the CONSOLE to the CONSOLE MAST using 2 PRE-INSTALLED CONSOLE SCREWS. SCREW Z41 Z41 CONSOLE SCREW CONSOLE SCREW 7XE SHOWN ASSEMBLY COMPLETE! 44 MX_12_HUR3x_5x_7xe_OM_Rev1_3.
CYCLE OPERATION 46 MX_12_HUR3x_5x_7xe_OM_Rev1_3.
MANAGER MODE AND ENGINEERING MODE 3X AND 5X CONSOLES: These sections allow users to manipulate default settings for the machines. It may be accessed by pressing the Level Up / Level Down keys simultaneously for 5 seconds. To change a setting, press “Enter” on the keypad under ‘Manager Mode’ or ‘Engineering Mode’ and use the level buttons and numeric keypad to enter a category and change the values. Pressing “Enter” again will save the change. Pressing “Back” or “Stop” will bring you to the previous menu.
H3X/ U3X / R3X CONSOLE DESCRIPTION A A Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) WORKOUT KEYS: Simple program view and selection buttons. B) GO: One Touch Start. C) ENTER: To confirm each program setting. D) UP/DOWN LEVEL: Use to adjust level selection. H C E) UP/DOWN TIME: Use to adjust workout time. F) STOP: Ends workout and shows workout summary data. G) COOL DOWN: Puts the console into Cool Down mode.
H5X / U5X / R5X CONSOLE DESCRIPTION Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) WORKOUT KEYS: Simple program view and selection buttons. B) GO: One Touch Start. G C) ENTER: To confirm each program setting. D E A H C D) UP/DOWN LEVEL: Easy information and level selection. E) UP/DOWN TIME: Easy information and time adjustment. F) STOP: Ends workout and shows workout summary data.
H7XE / U7XE / R7XE CONSOLE DESCRIPTION The 7xe has a fully integrated touch screen display. All information required for workouts is explained on screen. Exploration of the interface is highly encouraged. The information explaining how to program for various workouts will give an explanation about the contents of each screen on the 7xe. A A) GO: One Touch Start. B) STOP (displayed on-screen during workout): Ends workout and shows workout summary data.
WORKOUT DESCRIPTIONS QUICK START OPERATION LEVEL BASED PROGRAMS Press the GO button and the machine will enter into a manual mode of operation. All energy expenditure values will be calculated using the default weight measurement. Your Matrix machine offers a variety of level-based workouts to challenge users of all fitness levels. The following information will briefly explain the workout and how to program the machine for each workout selection.
WORKOUT DESCRIPTIONS USER DEFINED PROGRAMS (RANDOM) FAT BURN WORKOUT OPERATION There are 20 workout profiles in random mode. Profile will change each time random button is pressed. Fat burn is a level-based workout that is designed to help users burn fat through various resistance changes. To enter into this workout on the 3x or 5x, use the following guidelines. To enter into this workout on the 7xe, follow the on-screen prompts. To enter into this workout on the 3x or 5x, use the following guidelines.
WORKOUT DESCRIPTIONS AVAILABLE ON 7XE CONSOLES NIKE + OPERATION CONSTANT WATTS This program allows you to vary your cadence or RPM and the machine’s resistance will adjust accordingly to your selected goal. The quicker your stride the less resistance for the goal selected. To enter into this workout on the 3x or 5x, use the following guidelines. To enter into this workout on the 7xe, follow the on-screen prompts.
PRODUCT SPECIFICATIONS 62 MX_12_HUR3x_5x_7xe_OM_Rev1_3.
MODEL NAME CYCLE TYPE H-3x/5x/7x H7xe HYBRID CYCLE™ H5x HYBRID CYCLE™ FRAME PART # CONSOLE PART # MODEL NAME H3x HYBRID CYCLE™ HURE-5X-04-C R-3x/5x/7x R7xe RECUMBENT R5x RECUMBENT FRAME PART # H-3X/5X/7X-03-F HURESAC-7XE-04-C CYCLE TYPE HURE-3X-C CONSOLE PART # R3x RECUMBENT R-3X/5X/7X-03-F HURESAC-7XE-04-C HURE-5X-04-C HURE-3X-C FEATURES FEATURES CONTACT & TELEMETRIC HR SENSORS YES YES YES CONTACT & TELEMETRIC HR SENSORS YES YES YES HANDLEBAR DESIGN SEAT SIDE AND FRONT VERTICAL E
MODEL NAME CYCLE TYPE U-3x/5x/7x U7xe UPRIGHT U5x UPRIGHT FRAME PART # CONSOLE PART # U3x UPRIGHT U-3X/5X/7X-03-F HURESAC-7XE-04-C HURE-5X-04-C HURE-3X-C CONTACT & TELEMETRIC HR SENSORS YES YES YES HANDLEBAR DESIGN FULL RACING STYLE WITH ELBOW SUPPORT FULL RACING STYLE WITH ELBOW SUPPORT FULL RACING STYLE WITH ELBOW SUPPORT INTEGRATED ARM RESTS N/A N/A N/A THUMB SWITCH CONTROLS YES YES YES TECHNOLOGY JID BRUSHLESS GENERATOR JID BRUSHLESS GENERATOR JID BRUSHLESS GENERATOR POWER RE
1-866-693-4863 www.matrixfitness.com Matrix Fitness 1600 Landmark Drive, Cottage Grove, WI 53527 Matrix Bikes 1.3 | © 2012 Matrix Fitness MX_12_HUR3x_5x_7xe_OM_Rev1_3.
