COMMERCIAL SERIES TREADMILL OWNER’S MANUAL 06' Treadmill's OM.
06' Treadmill's OM.
TABLE OF CONTENTS CHAPTER 1: IMPORTANT SAFETY INSTRUCTIONS 1.1 1.2 1.3 1.4 1.5 PAGES Before Getting Started .................................................................................................... 01 Proper Usage ................................................................................................................. 01 Read and Save These Instructions ................................................................................... 01 Electrical Requirements ............
06' Treadmill's OM.
CHapter 1: Important Safety Instructions 1.1 Before getting Started 1.3 READ AND SAVE THESE INSTRUCTIONS It is the sole responsibility of the purchaser of Matrix Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel, on proper usage of the equipment. This Treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating the MATRIX treadmill.
CHapter 1: Important Safety Instructions CHapter 2: Preventative Maintenance 1.4 Electrical Requirements 2.1 RECOMMENDED CLEANING TIPS For your safety and treadmill performance, the ground on this circuit must be non-looped. Please refer to NEC article 210-21 and 210-23. Your Treadmill is provided with a power cord with a plug and requires a dedicated line according to the electrial configurations listed in the chart below. Any alteration of this power cord could void all warranties of this product. 1.
CHapter 2: Preventative Maintenance 2.4 ADJUSTING THE BELT CHapter 3: Serial Number Location 3.1 MX-T3x TREADMILL After placing the treadmill in the position it will be used, the belt must be checked for proper tension and centering. The belt might need to be adjusted after the first two hours of use. Temperature, humidity, and use cause the belt to stretch at different rates. If the belt starts to slip when a user is on it, be sure to follow the directions below.
CHapter 4: MX-T3x Overlay Description / Programing / Engineering Mode 4.1 MX-T3x Console description 4.2 manual operation The MATRIX treadmill is inspected before it is packaged. It is shipped in four pieces: the base, the upright console supports, the handlebar and the console. Carefully unpack the unit and dispose of the box material. matrix design makes using the programs as easy as one touch of a button. caution This unit weights 350 lbs / 159 kg.
CHapter 4: MX-T3x Overlay Description / Programing / Engineering Mode 4.4 Heart rate control 4.5 Fit test Follow these easy Steps to enter into the Heart Rate Program. FIT TEST allows you to measure your fitness based on a program designed specifically for your Matrix Treadmill. The test takes 5 minutes and is based on your heart rate. User should keep hands on contact heart rate graps. Target HR: 1) Choose the “TARGET HR” using the program QUICK-KEYS, then press SELECT.
CHapter 4: MX-T3x Overlay Description / Programing / Engineering Mode Men’s output table for test #1 AND #2 AGE EXCELLENT GOOD 15-19 61+ 56 ~ 61 20-29 57+ FAIR POOR 52 ~57 48 ~ 51 42 - 44 ~ 51 38 ~ 43 38 - 30-39 51+ 48 ~ 51 40 ~ 47 34 ~ 39 34 - 40-49 48+ 44 ~ 48 36 ~ 43 30 ~ 35 30 - 50-59 44+ 40 ~ 44 32 ~ 39 60-69 21+ 21 ~ 26 27 ~ 35 36 ~ 40 40 - 70-79 36+ 32 ~ 36 23 ~ 31 17 ~ 22 17 - 52 ~ 57 AVERAGE 4.
CHapter 4: MX-T3x Overlay Description / Programing / Engineering Mode 4.7 manager screen descriptions / details 4.8 USing Csafe Below is a list of the MX-T3x functions for each engineering screen. Exceptions will be noted in the description for each engineering screens: Matrix is the leader in entertainment availability. p0 low speed learn mode (edit) This variable controls the low limit for the speed of the treadmill.
CHapter 5: MX-T4x / MX-T5x Overlay Description / Programing / Engineering Mode 5.1 console description programs: Simple program view and selection buttons. Seven programs to choose from. start/quick start: One touch Start and Quick Start Select: Quick entry of information and level selection. pause/hold to reset: Stop/Pause and hold for 3 seconds to reset. clear: Clears number keypad entry. up/down elevation: Easy information and elevation selection.
CHapter 5: MX-T4x / MX-T5x Overlay Description / Programing / Engineering Mode 5.3 Operating level based programs 5.4 heart rate control Your matrix treadmill offers versatile programs to keep the usere motivated. The following instructions will guide you through simple steps to select INTERVALS, ROLLING, and RANDOM programs. For your convenience, matrix T5x Treadmills come standard with digital contact heat rate sensors and are polar telemetry compatible. The MX-T4x is only available with telemetry.
CHapter 5: MX-T4x / MX-T5x Overlay Description / Programing / Engineering Mode Men’s output table for test #1 AND #2 5.5 Fit test FIT TEST allows you to measure your fitness based on a program designed specifically for your Matrix Treadmill. The test takes 5 minutes and is based on your heart rate. User should keep hands on contact heart rate graps. Follow these easy steps to enter in the Fit Test Program.
CHapter 5: MX-T4x / MX-T5x Overlay Description / Programing / Engineering Mode 5.6 engineering mode 5.7 manager screens exceptions/details Manager screens allow the viewing and editing of variables that would be necessary for a club operator/manager to customize. Unless otherwise noted manager screens consist of the initial screen, the editing or action screen and the saving screen. The initial screen displays the variable type and in most cases the current value.
CHapter 5: MX-T4x / MX-T5x Overlay Description / Programing / Engineering Mode 5.8 using csafe p10 default channel (edit) Controls the default channel for enterainment CSAFE compativle devices. This variable is editable. Numeric entry is active. p11 default volume (edit) Controls the default channel for enterainment CSAFE compativle devices. This variable is editable. Numeric entry is active. p13 Speed mode (edit) Changes from Standard (Kilometers) to English (Miles).
CHapter 6: MX-T3x Treadmill Specifications, Parts, and Assembly Guides 6.1 MX-T3x Model Specifications SPECIFICATIONS Foot Print MX-T3x • Treadmill Weight Max User Weight Belt Type Frame Construction Running Area Incline Range Speed Min. Speed Max. Motor Type Controller Cooling Fan Deck Wax inches = 85” x 34” x 55” cm = 216 x 87 x 140 350 lbs / 159 kg 400 lbs = 182 kg Habasit Steel 20” x 60” 0-15% 0.5 mph / 0.8 kph 12 mph / 20 kph 3.
CHapter 6: MX-T3x Treadmill Specifications, Parts, and Assembly Guides 6.2 MX-T3x Model Required fasteners & Assembley Tools MX-T3x • Treadmill QTY PART # SKETCH DESCRIPTION 01 8mm ALLEN WRENCH 01 10mm ALLEN WRENCH 01 #2 PHILLIPS SCREW DRIVER [ 4.5 x 50 ] 08 Z50 FLAT WASHER 10 x 20 x 2.0t 08 Z51 SOCKET HEAD CAP SCREW M10 x 25L 04 Z52 SOCKET HEAD CAP SCREW M8 x 15L 02 Z53 BUTTON HEAD MACHINE SCREW M5 x 12L NOTES 14 06' Treadmill's OM.
CHapter 6: MX-T3x Treadmill Specifications, Parts, and Assembly Guides 6.3 MX-T3x Model ASSEMBLY STEPS • ATTENTION After installation is completed, the treadmill will need to be calibrated by using the auto-check function. If this is not done, the treadmill's speed and incline values may be incorrect and damage the treadmill. Do not stand on the belt when performing the auto-check function.
CHapter 6: MX-T3x Treadmill Specifications, Parts, and Assembly Guides 6.4 MX-T3x Model ASSEMBLY STEPS STEP 3 STEP 4 Z53 Z53 FINAL ASSEMBLY OPTIONAL ENTERTAINMENT ACCESSORY SHOWN FINAL ASSEMBLY AUTO CHECK • Press and hold both incline “UP” and speed “DOWN“ buttons simultaneously for 3 seconds .Then the “ENGINEERING MODE” is shown onto the console. • Press the incline “UP” button to find the “AUTO CHECK” screen.
CHapter 7: MX-T4x / MX-T5x Treadmill Specifications, Parts, and Assembly Guides 7.1 MX-T4x / MX-T5x Model Specifications SPECIFICATIONS Product Name Foot Print TIME DISTANCE ELEVATION SPEED 1 3 2 4 MANUAL ROLLING 5 6 7 8 9 0 RANDOM KEYPAD QUICK START SELECT CLEAR INTERVALS FIT TEST PAUSE HOLD TO RESET TARGET HR Weight T4x / T5x inches = 85” x 35” x 62” cm = 215.9 x 88.7 x 157.5 450 lbs / 204 kg Max User Weight Belt Type Frame Construction Running Area Incline Range Speed Min.
CHapter 7: MX-T4x / MX-T5x Treadmill Specifications, Parts, and Assembly Guides MX-T4x / MX-T5x • Treadmill 7.2 MX-T4x / MX-T5x Model Required fasteners & Assembley Tools QTY PART # SKETCH DESCRIPTION 01 Z13 4mm ALLEN WRENCH 01 Z12 5mm ALLEN WRENCH 01 Z09 ALLEN WRENCH [ #8 x 168 ] 01 Z10 ALLEN WRENCH [ #5 x 172 ] 01 Z08 #2 PHILLIPS SCREW DRIVER [ 4.
CHapter 7: MX-T4x / MX-T5x Treadmill Specifications, Parts, and Assembly Guides 7.
CHapter 7: MX-T4x / MX-T5x Treadmill Specifications, Parts, Assembly Guides and 7.
06' Treadmill's OM.
06' Treadmill's OM.
M AT r i x F i t n e s s s y s t e ms c o r p. I N T E R N AT I O N A L V E R S I O N REV. 02 06' Treadmill's OM.
