MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es MTX-HSPA-PH8-P+G TERMINAL User Manual Powered by CINTERION WM PH8-P HSDPA-UMTS Wireless Module MTX-HSPA-PH8-P+G User Manual V.1.0 Preliminary. Subject to change without prior notice Pag.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es General Notes Product is deemed accepted by recipient and is provided without interface to recipient’s products. The documentation and/or product are provided for testing, evaluation, integration and information purposes. The documentation and/or product are provided on an “as is” basis only and may contain deficiencies or inadequacies. The documentation and/or product are provided without warranty of any kind, express or implied.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 1. INTRODUCTION ..................................................................................................................................................... 5 1.1 Description ............................................................................................................................... 5 1.2 Highlights.......................................................................................................................
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem 6.1. 6.2. 6.3. 6.4. 6.5. 6.6. http://www.matrix.es Safety instructions ................................................................................................................. 25 General precautions ............................................................................................................... 25 SIM card precautions .............................................................................................................
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 1. INTRODUCTION 1.1 Description When your application needs to receive data up to 3.6 Mbps download or transmit up to 386Kbps, the MTX-HSPA-PH8-P+G terminal is the solution based on HSDPA technology. The HSPA (High Speed Downlink Packet Access) is a transmission standard based on the UMTS network which allows a download speed of up to 3.6 Mbit/s.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 1.2 Highlights General features: • HDPA 14.4 Mbps • Tri-Band UMTS/HSPA (WCDMA/FDD) 850/1900/2100 MHz • Quad-Band GSM 850/900/1800/1900 MHz • EDGE (E-GPRS) multi-slot class 10 • GPRS multi-slot class 10 • UMTS/HSDPA 3GPP release 5 • GSM 3GPP release 99 • Output power: - Class 4 (2 W) for GSM900 - Class 3 (0.25 W) for UMTS/HSDPA - Class E2 (0.5 W) for EDGE900 - Class E2 (0.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 1.3 Main Features and Services The MTX-HSPA-PH8-P+G perform a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The services and functions of the MTX-HSPA-PH8-P+G are implemented by AT commands issued over the USB or ASC0 RS232 interface. 1.3.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 1.3.2 Short Message Service The wireless modem supports the following SMS services: • Sending; MO (mobile-originated) with both PDU (protocol data unit) and text mode supported. • Receiving; MT (mobile-terminated) with both PDU and text mode supported. • CBM (cell broadcast message); a service in which a message is sent to all subscribers located in one or more specific cells in the GSM network (for example, traffic reports).
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem HSPA DATA http://www.matrix.es HSPA data transfer in progress. Power consumption depends on network settings (e.g. TPC Pattern) and data transfer rate. Power Down The internal power section is shut down. The SW on the module is not active. The interfaces are not accessible.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem IVUSB USB transceiver supply current (average) http://www.matrix.es HSDPA Data transfer Band I @+23dBm 775 mA USB suspend 0.5 mA USB active 3 mA 1. With an impedance of ZLOAD=50Ohm at the antenna connector. neighbouring cells; without t3212 timer occurrence. 3. Under total mismatch conditions at antenna connector. 2. Without 1.3.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es GSM 1800 -102 -107 dBm GSM 1900 -102 -107 dBm E-GSM 900 31 32 35 dBm GSM 1800 28 29.25 32 dBm GSM 1900 28 29.25 32 dBm Parameter Conditions Min. Typical Max.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 2. MECHANICAL DESCRIPTION 2.1 Overview The pictures below show the mechanical design of the module along with the positions of the different connectors and mounting holes. The module case is made of durable PC/ABS plastic. MTX-HSPA-PH8-P+G User Manual V.1.0 Preliminary. Subject to change without prior notice Pag.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 2.2. Dimensions Figure 5. Dimensions of the MTX-H25+PLUS terminal in mm MTX-HSPA-PH8-P+G User Manual V.1.0 Preliminary. Subject to change without prior notice Pag.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3. ELECTRICAL DESCRIPTION All electrical connections to the module are protected in compliance with the standard air and contact Electrostatic Discharge (ESD). The module uses the following industry standard connectors: USB port RJ12 6-way (power supply connector) RJ12 4-way (handset connector) SIM card reader FME male coaxial jack (antenna connector) 3.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3.2 Audio Connector A 6-way 4-poles RJ connector, as shown below, allows a telephone handset to be plugged into the modem, giving access to the microphone and earpiece signals. The connector may also be used to drive other analogue audio sub-systems or devices. The audio interface provides one analog input for a microphone and one analog output for an earpiece. • The microphone input and the earpiece output are balanced.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es The electrical characteristics are given in the table below. Audio mode no. AT^SNFS= 1 2 3 4 5 6 User Handset Headset Speaker phone Transparent Mono Headset Handheld speaker-phone Direct access to speech coder Name Default Handset Router Purpose DSB with Votronic handset Analogue phone interface TX-Filters Adjusted Flat Adjusted Flat Flat Flat RX-Filters Adjusted to fit artificial ear type 3.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3.3 Mini USB Connector The USB 2.0 interface allows the connectivity to all relevant PCs and control boards in office and industrial environments. The USB interface is a USB 2.0 full speed (12Mbit/s) interface for AT-C modem functionality between the MTX-HSPA-PH8-P+G Terminal and e.g. a PC. It can be operated on a USB 2.0 Full Speed or High Speed root hub (a PC host), but not on a generic USB 2.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3.5 UMTS-GSM Antenna Connector The antenna connector allows the transmission of radio frequency (RF) signals between the modem and an external customer-supplied antenna. The modem is fitted with a 50Ω, FME male coaxial jack. The external antenna must be matched properly to achieve best performance regarding radiated power, DC-power consumption, modulation accuracy and harmonic suppression. 3.6.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3.7. SIM card reader The MTX-HSPA-PH8-P+G Terminal is fitted with a SIM card reader and is designed for 1.8V and 3V SIM cards 3GPP 31.102 and ETSI 102 221. It is the flip-up type which is lockable in the horizontal position and is accessed through a removable panel as shown below: The card holder is a five wire interface according to GSM 11.11. It has a SIM card detector switch to detect whether or not the SIM card drawer is inserted.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 3.8 Real Time Clock The MTX-HSPA-PH8-P+G contains a real time clock (RTC) to maintain accurate timekeeping and to enable “time stamping” of messages. The internal Real Time Clock of MTX-HSPA-PH8-P+G is supplied from a separate voltage regulator in the analog controller which is also active when MTX-HSPA-PH8-P+G is in POWER DOWN status. By default RTC is not powered when MTX-HSPA-PH8 is switched off. Please contact gsmsupport@matrix.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 4. OPERATION 4.1 Switching On the Modem There is ONE way to switch on the modem once the power is applied: • assert TURN_ON high for > 0.4s; The modem is fully operational after 4 seconds. Logging onto a network may take longer than this and is outside the control of the modem. The modem can be configured to start up at the time power is applied by permanently tying power connector signals TURN_ON (pin 4) and VCC (pin 1) together. 4.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 4.3 Operating States/LED The modem has an LED which displays the operating status of the Terminal. An LED is provided for signaling the module’s network connectivity status. This status function has to be activated with AT^SLED=2. This command is VOLATILE; the configuration is lost when the terminal shuts down. Please ensure to write it on the configuration & initialization string.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 5. PH8 AT COMMAND INTERPRETER After a successful installation of the PH8 driver package, the physical USB interface of the module is represented in the operating system by two virtual interfaces, each assigned to a virtual COM port of its own: • Modem interface: This interface is referred to as "Modem" if queried with AT^SQPORT. In the quick reference tables it is named MDM.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 6 SAFETY AND PRODUCT CARE Please read the information in this section and the information in “Installation of the Modem” before starting your integration work! 6.1. Safety instructions PLEASE READ THESE SAFETY INSTRUCTIONS AND KEEP A COPY OF THEM. • Always ensure that use of the modem is permitted. The modem may present a hazard if used in proximity to personal medical electronic devices.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es • When the SIM card hatch is opened, the SIM card connectors lie exposed under the SIM card holder. Caution! Do not touch these connectors! If you do, you may release an electrical discharge that could damage the modem or the SIM card. • When designing your application, the SIM card’s accessibility should be taken into account. We always recommend that you have the SIM card protected by a PIN code.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 7. INSTALLATION OF THE MODEM This chapter gives you advice and helpful hints on how to integrate the MTX-HSPA-PH8-P+G Terminal into your application from a hardware perspective. 7.1 Where to install the modem There are several conditions which need to be taken into consideration when designing your application as they might affect the modem and its function. They are: 7.1.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 7.2.2 Securing the modem Before securing the modem, take into account the amount of additional space required for the mating connectors and cables that will be used in the application. • Where access is restricted, it may be easier to connect all the cables to the modem prior to securing it in the application. • Securely attach the MTX-HSPA-PH8-P+G Terminal modem to the host application using two 3mm diameter pan-head screws. 7.3 Antenna 7.3.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 7.3.5 Possible communications disturbances Possible communication disturbances include the following: • Noise can be caused by electronic devices and radio transmitters. • Path-loss occurs as the strength of the received signal steadily decreases in proportion to the distance from the transmitter. • Shadowing is a form of environmental attenuation of radio signals caused by hills, buildings, trees or even vehicles.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 9. CONFORMITY ASSESSMENT MATRIX ELECTRONICA S.L. Alejandro Sanchez 109 28019 Madrid Spain We declare under our sole responsibility that the products MTX-HSPA-PH8-P+G Terminal V2.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 10. ROHS STATEMENT The MTX-HSPA-PH8-P+G is compliant with the 2002/95/EC Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS). 11.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 12.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 13. AT COMMAND SUMMARY The AT standard is a line-oriented command language. AT is an abbreviation of ATtention and it is always used to start sending a command line from the terminal equipment (TE) to the terminal adaptor (TA). The command line consists of a string of alphanumeric characters. It is sent to the MTX-HSPA-PH8-P+G to instruct it to perform the commands specified by the characters.
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem AT+CIMI Request International Mobile Subscriber Identity (IMSI) AT+CLCC List current calls of ME AT+CLCK Facility lock AT+CLIP Calling Line Identification Presentation AT+CMEE Mobile Equipment Error Message Format AT+CMGC Send an SMS command AT+CMGD Delete short message AT+CMGF Select SMS message format AT+CMGL List SMS messages from preferred store AT+CMGR Read SMS messages AT+CMGS Send Short Message AT+CMGW Write Short Messages to Memory AT
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem AT+CSMP Set SMS text Mode Parameters AT+CSMS Select Message Service AT+CSQ Signal quality AT+CSSN Supplementary service notifications AT+CSTA Select type of address AT+ES Synchronous Data Mode Configuration AT+ESA Synchronous access mode configuration AT+GCAP Request complete TA capabilities list AT+GMI Request manufacturer identification AT+GMM Request model identification AT+GMR Request revision identification of software status AT+GSN Reque
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem ATQ Set result code presentation mode ATS0 Set number of rings before automatically answering a call Set disconnect delay after indicating the absence of data carrier ATS10 ATS3 Set command line termination character ATS4 Set response formatting character ATS5 Write command line editing character ATS6 Set pause before blind dialling ATS7 ATT Set number of seconds to wait for connection completion Set number of seconds to wait for comma dialling modifie
MTX-HSPA-PH8-P+G UMTS-HSPA terminal modem http://www.matrix.es 14. SALES CONTACT www.mtx-terminals.com gsmsupport@matrix.es Matrix Madrid Matrix Electronica S.L.U. C/ Alejandro Sánchez, 109 28019 - Madrid Spain Tel. +34 91 5602737 Fax. +34 91 5652865 matrix@matrix.es MTX-HSPA-PH8-P+G User Manual V.1.0 Preliminary. Subject to change without prior notice Pag.