MS001/MS002 Single Oven Manual for Installation, Use and Maintenance
Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Important • Read the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly. • Remove spills as soon as they occur. • Always use oven gloves when removing shelves and trays from the ovens. • Do not allow children near the oven when in use. • Do not allow fat or oils to build up on the oven shelves, grill pan or oven base. • Do not place any cooking utensils or plates directly on the oven base.
First use of the oven First use • Before using the oven for the first time we recommend that you clean the oven with soapy water, rinse carefully and then heat on each of the below programmes at maximum temperature for the specified time. A slightly unpleasant smell may be produced, caused by grease remaining on the oven elements from the production process. 15 minutes grill. 60 minutes fan oven.
Oven controls and use Cooking function knob To set the function, turn the cooking function knob to the required function. Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time. These are explained below: Defrost Using the fan only this oven function circulates the air around the oven cavity, speeding up the natural defrost process (1kg takes approximately one hour, depending on the type of food).
Programming the oven (MS002 only) IMPORTANT: THE CLOCK MUST BE SET TO ENABLE THE OVEN TO WORK. functions To confirm a selection when programming the clock/timer, once the display shows the preferred selection simply do not touch any further keys for approximately five seconds. The oven will automatically confirm the selection. display field 1 2 3 4 5 buttons 6 fig. 1 The alert beep will cut off after seven minutes if it is not switched off manually.
Programming the oven (MS002 only) The oven can be set for semi-automatic cooking, where the oven is programmed to switch off at a specific time, and for automatic cooking, where the oven is set to switch on and off at specific times. To use the oven, first press button 4 To set a semi-automatic programme 1. Select the required function and temperature (the oven will switch on). 2. Press button 2 and then press button 5 or 6 to select the required duration of cooking (maximum of 10 hours).
Care and Maintenance IMPORTANT Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. The oven exterior As the oven has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings.
Changing the Oven Lamp Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. IT Changing the bulb (fig. 2) • Unscrew the protective cover. • Unscrew and replace the bulb with the new one suitable for high temperatures (300ºC) having the following specifications: 230-240V, 50Hz, 25W E14 (SES).
Installation Important If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not installed as it could restrict ventilation. Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide and a minimum of 15mm high to allow air to pass under the unit.
Electricity supply to your oven Warning! this appliance must be earthed. This appliance must be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet, protected by a 13A fuse. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E and local regulations.
Serviced by To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
