MD720 Built-Under Double Oven MD920 Built-In Double Oven Manual for Installation, Use and Maintenance 1 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model Serial Number CE Declarations of Conformity: This oven has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (Low voltage) and requirements of EMC Directive 2004/108/EEC.
disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin. Important • Read the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly. • Steam cleaners must not be used when cleaning this appliance.
• Do not use abrasive cleaners or powders that will scratch the surface of the enamel. • Do not attempt to repair the internal workings of your oven. • The oven is equipped with a safety thermostat which will switch off the oven in the event of the oven overheating. If the safety thermostat should switch off the power, you must wait for the oven to cool down before using it again.
Oven controls and use Cooking function knob To set the function, turn the cooking function knob for the required oven clockwise to the required function. Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time. These are explained below: Conventional oven This function uses the top and bottom heating elements only with a temperature between 50ºC and 250ºC.
When grilling, please note: • Always grill with the oven door closed. • Put the grill pan as close to the grill as possible. • Do not grill for more than 30 minutes at a time. • Preheat the grill for approximately five minutes with the oven door closed. Oven Lamp This function switches on the oven light in the cavity.
Temperature knob • To set the temperature, turn the temperature knob for the required oven clockwise to the required temperature. • | Once the oven has reached the required temperature, the temperature indicator lamp on the control panel will switch off. • The temperature indicator lamp will light up when the oven elements are working. Programming the oven IMPORTANT: THE CLOCK MUST BE SET TO ENABLE THE OVEN TO WORK. functions display field 1 2 3 4 5 buttons 6 fig.
When the correct time is shown on the display, the clock will set after approximately five seconds’ delay. Setting the volume of the beep • When the current time is shown on the clock display, press and hold button 5. The beep will sound three times. • Continue to press button 5 until the volume is at the correct level. Each press of the button will cycle through the options. The minute minder The minute minder can be used when the oven is switched on or off.
Programming the oven The oven can be set for semi-automatic cooking, where the oven is programmed to switch off at a specific time, and for automatic cooking, where the oven is set to switch on and off at specific times. To use the oven, first press button 4 To set a semi-automatic programme 1. Select the required function and temperature (the oven will switch on). 2. Press button 2 and then press button 5 or 6 to select the required duration of cooking (maximum of 10 hours).
When the cooking time is completed, the programme symbol will no longer be shown, auto will flash and the timer will beep. To switch off the beep, press any button. Then switch off the oven by turning the control knobs to the off position and pressing button 4 to set the programmer to manual. To cancel a programme Press buttons 2 and 3 simultaneously, or button 4. Please note : At the end of a programme, the timer will not switch off the oven. Remember to turn off the oven manually.
Care and Maintenance IMPORTANT Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. The oven exterior As the oven has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings.
IMPORTANT: • Steam cleaners must not be used when cleaning this appliance. • Once care and maintenance is complete, ensure that all parts are correctly replaced before using the oven. Changing the Oven Lamp Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. Changing the bulb (fig. 2) Unscrew the protective cover.
Refit the protective cover. IMPORTANT Never use screwdrivers or other utensils to remove the light cover. This could damage the enamel of the oven or the lamp holder. Remove only by hand. IMPORTANT Never replace the bulb with bare hands as contamination from your fingers can cause premature failure. Always use a clean cloth or gloves. Please note: The bulb replacement is not covered by your guarantee.
Cleaning and Maintenance Removing the Oven Door The oven doors can easily be removed as follows: • Open the door to the full extent (fig. 3.1). • Open the lever A completely on the left and right hinges (fig. 3.2). • Hold the door as shown in fig. 3. • Gently close the door (fig. 3.3) until left and right hinge levers A are hooked to part B of the door (fig. 3.2). • Withdraw the hinge hooks from their location following arrow C (fig. 3.4). • Rest the door on a soft surface.
Mains Electricity Connection Warning! This appliance must be earthed To connect this appliance to a UK standard mains supply, connect the bridging links between 1-2-3 for the live feed and 4-5 for the neutral feed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. 1 2 3 4 fig.
Green and Yellow = Earth (PE) Blue = Neutral Brown = Live Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 2.5mm2, HO5RR-F). • This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5 mm2. A larger cable will not fit the terminal connections.
Installation Important Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could invalidate the warranty. The diagram below shows the minimum required. This appliance is type X installation. The walls of the kitchen units must be able to withstand temperatures of 75oC above ambient (typically this is between 90oC and 100oC).
MD720 MD920 Dimensions Oven Housing Dimensions Oven Height (mm) 718 720 Height (mm) 890 877 Width (mm) 595 560 Width (mm) 595 560 Depth (mm) 540 560 (min) Depth (mm) 540 560 (min) MD720 MD920 560 end support panels 718 30-50 = airflow 560 105 556 720 min 556 560 595 fig.
Serviced by To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style 20 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
