MASTERSOUND M a s t e r E m o t i o n Compact 300 B Made in Italy
Our Philosophy Our philosophy is simple: we want to produce amplifiers which stimulate the emotions for those who enjoy music. We believe that every piece of music played through our amplifiers should arouse in the listener the same emotions as the artist who composed it and the musician who interpreted it.
Mastersound story MasterSound is an Italian company which has produced, for the past 15 years, class “A”, tube amplifiers. Our most important priority is to build equipment of the highest quality. We give the highest attention to quality in our design, our components, and our construction. Each part of our amplifier has been hand built with passion and skill. Our attention to detail will guarantee years and years of trouble free listening.
Integrated Amplifier Compact 300 B The Compact 300 B is the culmination of the collective knowledge and experience of all those who work with Master Sound. The total absence of feedback makes the Compact 300 B fast, with imaging that is truly amazing. Our new pre-amp section, of the Compact 300 B grew from our careful research. Combined with our unique output transformer and powerful, the 300 B triodes working in Single Ended mode, the amplifier renders a genuinely engaging sound.
Inside We built the Compact 300 B with the utmost care, using only selected materials. Our product passed the stricter quality tests with excellent results and is now ready to offer You many years of pleasant listening. A new amplifier needs to be put on at low volume in order to perform at its best the musicality and high definition of sound.
Tubes installation During the transportation the tubes are kept in an appropriate box and then they must be placed in the correct position (see the photo above). The 845 tube is indicated either by letter A, B, which stand between the pins and are written on the base: that is the right place for the tube to be installed.
Rear view 1. The bias control input. 2. Holder containing a plug with incorporated fuse. 3. Six speakers connectors :two with black rings and four with red rings (8-4 ohms). 4. Six RCA connector for the inputs line and two for the Direct 5.
Check list To be done by the dealer: set up the amplifier with the right impedance 4/8 ohm suitable for the speakers and select the right main line according to country. The above checks are to be made inside the amplifier and shall be carried out only by qualified staff. To be done by the Purchaser: 8 • Place the amplifier on a solid and flat surface. • Place the tubes in their correct socket positions.
Switching on of the amplifier A red led flashing lights, which should go on when You switch on the amplifier, indicating the correct functioning. When the inner tensions have reached the correct level, while the red led light grows bright, the Compact 300 B is ready to work. Only after the amplifier be pre-heated for at least thirty minutes, will it reach the ideal temperature so as to get the best results in listening Last recommendations Never remove or insert the AC plug when the unit is on.
Maintenance of the amplifier Avoid extremely hot locations such as near radiators, stove or other heating units. Use gently a wet and soft cloth (buckskin) to clean Your amplifier and dry immediately. Never clean Your amplifier when hot or running. Do not forget to take out the plugs before starting to clean the amplifier. .
Specifications • Integrated tube amplifier • Single Ended in Classe “A” • A selected pair out tubes triode 300 B • Pre-driver selected tubes 2 x ECC 802 • Driver selected tubes 2 x 6SN7 EH • Power output 15 Watts /Channel • Inputs: 3 x Line + 1 Direct • Input sensitivity 1 Volt • Input impedance 100 K Ohm • Load impedance 4 - 8 Ohm • Output transformer Mastersound • Negative feedback “non-existent” 0 db • Frequency 8 Hz / 40 Khz – 0 db • Volume with remote control • Dimensions
Warranty Your Compact 300 B , except the tubes, comes with a five years limited warranty covering defects in material and craftsmanship. During the warranty period, repairs are provided free of charge. Transportation costs and from the repair provider has to be paid by the owner. This warranty is void when: • the serial numbers have been removed • the screws fixed to the underside, have been removed • other kind of tubes different from the original have been used.
