20 Volt Worklight PUSH 241-0423 OPERATOR’S MANUAL CAUTION: Read, understand and follow all safety rules and instructions before using this tool. These safety instructions should be followed at all times. Failure to follow these safety instructions could result in injury to yourself or others. Also, failure to read and follow these instructions may cause damage to your equipment. For questions / comments, technical assistance or repair parts – Please Call Toll Free: 1-866-917-4374. (M-F 8am – 6pm EST.
table of contents Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Overview/Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 7-8 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
safety symbols Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.
safety INSTRUCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
safety INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Electrical safety Read all of the instructions before using the appliance. 1. To reduce the risk of injury, close supervision is necessary when an appliance is used near children. 2. Only use attachments recommended or sold by the manufacturer. 3. Do not use outdoors. 4. For a portable appliance – To reduce the risk of electric shock, do not put Flashlight and Battery Pack in water or other liquid.
safety INSTRUCTIONS 3. When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, also seek medical help.
safety INSTRUCTIONS 15. For best results, your battery tool should be charged in a location where the temperature is more that 32°F (0°C) but less that 104°F (40°C). Do not store outside or in vehicles. 16. Do not permit children to use the worklight; it is not a toy. CAUTION: Hot surface! Risk of burns-do not touch! CAUTION: Risk of fire-keep away from combustible materials. SAFETY RULES FOR CHARGER WARNING: Read and understand all instructions.
safety INSTRUCTIONS 10. Do not operate the charger if it has received a sharp blow, been dropped, or has otherwise been damaged in any way. Take it to a qualified service technician for an electrical check to determine if the charger is in good working order. 11. Do not disassemble the charger. Take it to a qualified service technician when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12.
Specifications Illumination source Incandescent lamp Run-time More than 2 hours Bulb Type Incandescent ( single contact base) Bulb power 18V DC 300mA Pivoting head 90 degrees Pivoting handle 130 degrees Worklight weight (without battery) 10 oz. assembly WARNING: If any part is broken or missing, DO NOT attempt to attach the battery or operate the worklight until the broken or missing part is replaced. Failure to do so could result in possible serious injury.
operation TO ATTACH BATTERY PACK (FIG. 2) FIG. 2 ADJUSTING THE WORKLIGHT HANDLE AND HEAD (FIGS. 3-4) FIG. 3 PUSH Handle adjusts 130° PUSH 1. Align the raised portion on the battery pack with the grooves on the bottom of the worklight, and then attach the battery pack to the worklight as shown. FIG. 4 2. Make sure the latch on the battery pack snaps into place and the battery pack is secured to the worklight before beginning operation. TO DETACH BATTERY PACK (FIG.
Maintenance GENERAL MAINTENANCE The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time let brake fluid, gasoline, petroleum-based products, penetrating oils, etc.
Maintenance BULB REPLACEMENT (FIG. 5) FIG. 5 To loosen To tighten PUSH 1. Remove the battery pack from the worklight. 2. Rotate the reflector counterclockwise to remove it. 3. Remove the old bulb by rotating it. 4. Insert new bulb by rotating bulb in place. 5. Align the reflector and rotate it clockwise to tighten into place. WARNING: ONLY use recommended replacement bulbs; other bulbs may cause personal injury. NOTICE: Use 18V bulbs rated current larger than 300mA.
notes Page 12
notes Page 13
20 VOLT WORKLIGHT WARRANTY 90-DAY MONEY BACK GUARANTEE: This MASTERFORCE® brand power tool carries our 90-DAY Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund – no questions asked.
© 2013 Menard, Inc.
