User Manual

n
egyxO
Hydrogen
Explosive
Combustible
MC-OM-02
MC-OM-01
MAXIMUM TEMPERATURE
OPERATING TEMPERATURE
TECHNICAL SPECIFICATIONS
SAFETY GUIDELINES
AIR INLET/OUTLET
This manual contains information that relates to
PROTECTING PERSONAL SAFETY and PREVENTING
EQUIPMENT PROBLEMS. It is very important to read
this manual carefully and understand it thoroughly
before using the product. The symbols listed below are
used to indicate this information.
DANGER!
Potential hazard that will result in serious injury or loss
of life.
WARNING!
Potential hazard that could result in serious injury or
loss of life.
CAUTION!
CAUTION!
Potential hazard that may result in minor or moderate
injury.
NOTICE!
Potential hazard that may result in damage to
equipment.
Note The word “Note” is used to inform the reader of
something the handler needs to know about the tool.
These precautions are intended for the personal safety of the user and others working with the user. Please take time to read and understand them.
DANGER!
Potential hazard that will result in serious injury
or loss of life.
Keep ch
i
l
d
ren away from the work area.
•
•
•
•
•
•
•
•
Recycle unwanted materials rather than
disposing of them as waste. Sort the devices, hoses,
and packaging into specific categories and take to
the local recycling centre or dispose of them in an
environmentally safe way.
General usage description
The Mastercraft
®
General Purpose Air Filter is
designed to use with an air supply system to
remove solid particles from the air.
GUIDELINES FOR PROPER
USE AND OPERATION
After unpacking the filter, inspect it carefully for
any damage that may have occurred during transit
and tighten fittings, bolts, etc., before using the
filter.
Air system
Always use clean, dry, and compressed air.
Do not operate the filter at maximum or
minimum pressure.
It is recommended that the filter to be located
as close to the air supply system as possible.
NOTICE!
Potential hazard that may result in damage
to equipment.
•
•
•
•
•
•
CAUTION!
Potential hazard that may result in minor
or moderate injury.
AVERAGE AIR FLOW
MAXIMUM AIR FLOW
WAY OF DRAIN
125°F
(52
°
C)
5°C
(41
°
F)
MAXIMUM PRESSURE
150 PSI
FILTER ELEMENT
5 micron
WORKING PRESSURE
10–125 PSI
1/4"
(6.35 mm)
NPT
22 S
CF
M @ 9
0
PSI
64 SCFM @ 9
0
PSI
MANUAL
WORKING MEDIUM
Air
NP
T
: National Pipe Thread.
S
C
FM:
Standard Cubic Feet per Minute (the
volumetric flow rate of air corrected to standardized
conditions of temperature and pressure).
If any parts are missing or damaged, or if you have any questions, please call 1-800-689-9928.
N
o.
De
sc
ription
Air inlet
1
Air flow direction arrow2
Air outlet3
Bowl4
N
o
. N
o.
D
es
c
rip
ti
o
n
D
e
s
c
r
i
p
ti
o
n
Q
ty.
1
1
9
2
1
10
3
1
11
4
1
5
1
6
1
7
1
8
Body valve
Fitting seat
O-ring
Nut
Cyclone blade
K-ouch
Filter element
Baffle
Screw
Water glass
Drain fitting 1
Qty.
1
1
1
N
o.
D
es
c
r
i
p
ti
o
n
1
2
3
4
5
6
7
8
9
Air tool
Quick coupler
Quick connector
Air hose
Air filter
Modular bracket
Pressure regulator
Lubricator
Shut-off valve
Air compressor01
1
2
4
5
7
8
9
10
6
Do not use this device in the presence of flammable
liquids or gases.
Do not use or inject oxygen, any
other combustible gas such as
Liquefied Petroleum Gas (LPG) or
into the air
supply system as the to-be-filtered material.
Failure to observe this warning can cause
explosion and serious personal injury or death.
Do not wear watches, rings, bracelets, or loose
when using the filter.
combustible liquid such as alcohol
clothing
Always ensure that the filter is in safe working
condition before use.
Disconnect the filter from the air supply line
before performing any maintenance or
changing accessories, when the filter is not in
use, when it is handed to another person, and
when it is left unattended.
Use safety goggles
Wear safety glasses with side shields when
operating the filter and verify that others in the
work area are also wearing safety
glasses. Safety glasses must conform
to American National Standards
Institute (ANSI Z87.1) requirements and must
provide protection from flying particles from the
front and the sides. Failure to comply may
result in moderate injury.
Allow the filter to
operate at its optimum pressure for maximum
efficiency.
Do not overload the filter.
•
Do not use an air supply system that is leaking
air, with missing or damaged parts, or that
Verify that all nuts, bolts and
screws are securely tightened.
requires repairs.
Note:
Potential hazard that may result in moderate injury.
Verify that all connections in the air supply
system are sealed in order to prevent air from
leaking. Failure to comply may result in
moderate injury.
Read this instruction manual thoroughly or have
operators read thoroughly before using the tool.
Read all safety guidelines
at the beginning of this manual.
(see section “Safety
guidelines”)
Always inspect the filter prior to each use to
– ensure proper use of power source.
– determine whether the filter is in proper
working order.
3
MINI AIR FILTER 058-8125-0 MINI AIR FILTER 058-8125-0MINI AIR FILTER 058-8125-0
WARNING!
Potential hazard that could result in serious
injury or loss of life.
•
•
•
•
•
•
Do not use the device if it is not in proper
working order.
Do not use or inject oxygen or any other
combustible gases or liquids into the air supply
system as the to-be-filtered material.
Keep the air supply line away from heat, oil, and
sharp edges. Check the air supply line for wear
and tear, and ensure that all connections are
secure.
Storage
When the filter is not in use, disconnect it from
the air supply, clean, and store it in a safe, dry,
and childproof location.
The filter should be stored in a clean and dry
environment.
When temperatures are below freezing, keep the
filter as warm as possible using any safe,
convenient method.
•
Clean the air inlet and the filter weekly.
1
2
3
4
1
2
3
4
5
6
7
8
9
10
11
1 2