Model no. 058-1926-6 Flux Core 125i Welder IMPORTANT: Please read this manual carefully before using this welder and save it for reference.
Model no.
TABLE OF CONTENTS NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-800-689-9928. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. Read all instructions and follow them when using this product. Conforms to the standard of CAN ICES-1/NMB-1.
SPECIFICATIONS SPECIFICATIONS 5 Modelno. no.058-1294-8 058-1926-6 || contact contact us us 1-800-689-9928 1-800-689-9928 058-8194-4 model SAFETY GUIDELINES Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions.
7 Modelno. no.058-1294-8 058-1926-6 | | contact contactus us1-800-689-9928 1-800-689-9928 model model 058-8194-4 PACKAGING CONTENTS ASSEMBLY PREPARATIONS 1.1 Remove cartons, bags or foam containing the welder and accessories. 1.2 Check the contents with the packing list below. Instructions for shoulder strap installation ITEM QTY. Flux Core Inverter Welder Welding torch Grounding clamp with 6' (1.8 m) cable Contact tip 0.030''(0.
9 model 058-8194-4 contactus us1-800-689-9928 1-800-689-9928 Modelno. no.058-1294-8 058-1926-6 | | contact model ASSEMBLY INSTRUCTIONS 1. Power requirement AC single-phase 120 V (110 -130 V), 60 Hz fused with a 20-A time-delayed fuse or circuit breaker is required. DO NOT OPERATE THIS UNIT if the ACTUAL power source voltage is less than 105 V AC or greater than 132 V AC. 3.2.
RECOMMENDED WIRE 3.6 Depending on the wire diameter, select the correct groove according to the following table about the relationship between wire diameter and wire roller groove size. ASSEMBLY INSTRUCTIONS 11 Modelno. 058-1926-6 | | contact model no.058-1294-8 058-8194-4 contactus us1-800-689-9928 1-800-689-9928 model Wire Diameter Roller Groove 0.030" (0.8 mm) 0.030" (0.8 mm) 0.035" (0.9 mm) 0.035" (0.9 mm) This welder uses both 4" (10 cm) spools of 0.030 or 0.035" (0.8 or 0.9 mm) thick wire.
4.2.5 The welder can use 4" (10 cm) spool, please see the following chart. The adjustment knob is designed to adjust the pressure tension of the wire spool. 4" (10 cm) spool ASSEMBLY INSTRUCTIONS 13 Model no. 058-1926-6 | contact us 1-800-689-9928 8" (20 cm) 4.2.6. Once adjustment knob is installed, set the spool tension. a) With one hand, turn the wire spool and continue turning it while adjusting the tension on the spool. b) With your free hand, tighten the drive tension adjustment knob.
KEY PARTS DIAGRAM A Power indicator Overload Indicator Welding Voltage Welding Cable and Flux-Core Gun Welding cableand andclamp MIG gun Ground cable B C D KEY PARTS INSTRUCTIONS 15 model no. 058-8194-4 contact us 1-800-689-9928 Modelno. no.058-1294-8 058-1926-6 ||| contact contactus us1-800-689-9928 1-800-689-9928 model E F G ON/OFF switch Power cord H A B C D E POWER INDICATOR When the machine is turned on, the power indicator will be on.
16 17 Modelno. no.058-1294-8 058-1926-6 | | contact contactus us1-800-689-9928 1-800-689-9928 model 058-8194-4 1. Main control component Power switch－The power switch supplies electrical current to the welder. Whenever the power switch is in the ON position, the welding circuit is activated. ALWAYS turn the power switch to the OFF position and unplug the welder before performing any maintenance. Voltage selector－The voltage selector controls the welding heat. This unit has two -step voltage control.
19 Model no. 058-1926-6 | contact us 1-800-689-9928 5.4. With your free hand, turn the wire speed dial to maximum and continue to hold onto the knob. 5.5. Lower your welding helmet and pull the trigger on the torch to start an arc, then begin to drag the torch toward you while simultaneously turning the wire speed dial counter-clockwise. 5.6.
21 Modelno. 058-1926-6 | | contact model model no.058-1294-8 058-8194-4 contactus us1-800-689-9928 1-800-689-9928 6.3 Welding position 6.4 Multiple pass welding FLAT POSITION This is easiest of the welding positions and is most commonly used. It is best if you can weld in the flat position if at all possible as good results are easier to achieve. Butt Weld Joints.
MAINTENANCE The welder needs regular maintenance: • Periodically clean dust, dirt, grease, etc. from your welder. Every six months, or as necessary, remove the cover panel from the welder and air blow any dust an d dirt that may have accumulated inside the welder. • Replace power cord, ground cable ground clamp, or electrode assembly when damaged or worn. • Store in a clean dry facility, free from corrosive gas, excess dust and high humidity.
EXPLODED VIEW PARTS LIST 25 model no.058-1294-8 058-8194-4 contactus us1-800-689-9928 1-800-689-9928 Modelno. 058-1926-6 | | contact model PARTS LIST NO. Description QTY. NO.
3-Year Limited Warranty This Mastercraft product is guaranteed for a period of three (3) years from the date of original retail purchase, against defects in materials and workmanship. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification), at our option.
modelno. no.
