If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-877-888 -3872. Quick Start Guide Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice. Keep this instruction manual for future use. Should this product be passed on to a third party, this instruction manual must be included.
0 (0ff) Set the power switch to the 0 (off) position. STEP 2 Close the tank drain valve, located on the bottom of the air tank. CLOSE Turn the air pressure regulator knob counter-clockwise until it stops. SAFETY GUIDELINES CLOSE Set the power switch to the I (on) position. NOTE: For details, refer to the accessories diagram on page 14. 2-GALLON (7.6 L) AIR COMPRESSOR - 058-7000-2 OPEN 3 4–6 KEY PARTS DIAGRAM 7 KEY PARTS LIST 8 INTENDED USE STEP 5 STEP 6 Attach hose and accessories.
PRODUCT NUMBER 058-7000-2 PEAK HORSEPOWER 1/3 TANK SIZE 2 U.S. GALLONS (7.6L) This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. AIR DELIVERY (SCFM*) @ 40 PSI 1.0 DANGER! Potential hazard that will result in serious injury or loss of life. AIR DELIVERY (SCFM*) @ 90 PSI 0.
5 6 RISK OF PERSONAL INJURY. Never spray compressed air or material at self or others. 5. RISK OF BURSTING. Check the maximum pressure rating in the manual or identification label. The compressor outlet pressure must be regulated so that it does not exceed the maximum pressure rating. Relieve all pressure in the hose before removing or attaching accessories. 6. RISK OF BURSTING. Do not adjust the pressure switch or safety valve for any reason.
7 8 A. ELECTRIC MOTOR: The motor is used to power the pump. OUTLET PRESSURE GAUGE (I) ELECTRIC MOTOR (A) TANK PRESSURE GAUGE (H) POWER SWITCH (C) C. POWER SWITCH: This switch turns the compressor on and off. It is operated manually and when it is in the ON position, it allows the motor to start if the pressure in the air tank is below the factory set cut-in pressure, and allows the motor to stop if the pressure in the air tank reaches the factory set cut-out pressure.
Before you start This Mastercraft® Air Compressor is ideal for a wide-range of applications from fastening to greasing and engine cleaning. The 2-gallon (7.6 L) design provides optimum pressure. It is light weight and oilfree. It comes standard with a recoil hose and attachment fittings. The procedures described in this manual are solely for this 2-gallon (7.6 L) air compressor at a maximum of P=100 PSI. The device has been designed / constructed for household use only.
11 12 Unpack the air compressor. Inspect the unit for damage. If the unit has been damaged, contact the retailer immediately. IMPORTANT! If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-877-888-3872. THE CARTON SHOULD CONTAIN: • Air compressor • Owner’s manual ACCESSORY QTY 11/16” open-end wrench or 1 Adjustable wrench 1 Cross-headed screwdriver 1 2.
14 4. Connect air hose to compressor • Apply plumber's tape on the hose threads to prevent air leakage. • Screw the hose connector into the air outlet (K) on the air compressor. 5. Attach other accessories Tire chuck Tapered nozzle End of hose Air outlet (K) Hose connector or inflation needle Blow gun adaptor or low gun ASSEMBLY ASSEMBLY 13 or quick connector NOTE: Tire chuck assembly: Attach the tire chuck to the hose and tighten securely with a wrench.
Before each start-up How to shut down 1. 2. 3. 1. 2. 3. Set the power switch (C) to the 0 (off) position. Turn the air pressure regulator knob (G) counter-clockwise until it stops. Attach hose and accessories. WARNING! Risk of bursting. Too much air pressure causes a hazardous risk 16 Set the power switch (C) to the 0 (off) position. Unplug the power cord (E). Reduce the pressure in the tank through the outlet hose.
MAINTENANCE ITEM Drain the tank DESCRIPTION / REASON Through normal operation of your air compressor, condensation water will accumulate in the tank. To prevent corrosion of the tank from the inside, condensation must be drained at the end of every workday. Be sure to wear protective goggles. Relieve the air pressure in the system and open the drain valve on the bottom of the tank to drain.
20 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTIONS The power cord is not plugged in. Plug the power cord into a grounded outlet. The power switch is in the 0 (off) position. Set the power switch to the I (on) position. The extension cord is the wrong wire gauge or is too long. The motor’s thermal overload protection has tripped. Check Technical Specications chapter The motor runs continuously when the power switch is in the I (on) position.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 screw M6*12 motor cover sheath rubber power switch screw M4*40 cylinder cover silica gel ring Ø31.5*1.8 cylinder washer silica gel ring Ø31*2 cylinder paper pad silica gel ring 21.2 piston ring connecting rod clamp bearing 608-2RS screw M5*10 crank screw M4*8 circuit board screw M6*25 flat washer Ø6 motor fan flat washer 1- 877- 888 - 3872.
24 Additional Limitations 3 YEAR LIMITED WARRANTY This Mastercraft® product is guaranteed for a period of three years from the date of original retail purchase against defects in materials and workmanship. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification), at our option.
