________________________________________________________________________________________________ MASTERCALL TELEPHONE CALL DIVERTER MODEL MC-4044 SERIES 5 ________________________________________________________________________________________________ INSTRUCTION AND INSTALLATION MANUAL G/93040 EDITION 6 MARCH, 2001 AUSTEL PERMIT NUMBER A94/05/0234 ACA SUPPLIER’S CODE N468 ________________________________________________________________________________________________ DESIGNED AND MADE IN AUSTRALIA DE
__________________________________________________________________________________________________ MASTERCALL MC-4044 TELEPHONE CALL DIVERSION SYSTEM ________________________________________________________________________________________________ Section 1 General Description Of MASTERCALL MASTERCALL MC4044 Diverter 1 Section 2 Installation Instructions Diverter Connection 1 Section 3 Programming Instructions Diversion Activate/Deactivate Keypad Enable/Disable Diversion Number(s) Identification Tone C
__________________________________________________________________________________________________ MASTERCALL TELEPHONE CALL DIVERSION SYSTEM DESIGN TWO THOUSAND PTY LTD MELBOURNE AUSTRALIA SECTION 1 - GENERAL DESCRIPTION OF THE MASTERCALL SYSTEM The MASTERCALL Call Diverter manufactured by Design Two Thousand Pty Ltd diverts incoming calls on one line via a second line to any dial up telephone number.
__________________________________________________________________________________________________ SECTION 3 - PROGRAMMING INSTRUCTIONS AT THE KEYPAD The operation of the diverter at the keypad is detailed in this section. As the diverter is normally ‘asleep, ie. the microprocessor is not running, the first key should be pressed for approximately half a second to ensure correct function. The ‘awake’ state is indicated by the decimal point on the 7 segment display.
__________________________________________________________________________________________________ Diversion If No Answer MASTERCALL can be programmed to divert after a preset delay. When MASTERCALL is in the deactivated state and there is an incoming call which is not answered after the delay, MASTERCALL will process the call and then resume the deactivated state after the call. The delay before diversion is entered as a 3 digit number which is the delay in seconds. 1. * 6705 # 2.
__________________________________________________________________________________________________ Change the diversion number 1. 2. 3. 4. Press 2 (or 5 to change the second diversion number) After the prompt has finished, enter the required number Press # The new number will then be replayed. The programming can be done in any sequence. Once programming is completed, replace the receiver and MASTERCALL will hang up in 5-20 seconds. Do not test the diverter until 20 seconds have elapsed.
__________________________________________________________________________________________________ To Disable The Personalised Diversion Announcement (from the Keypad): 1. Press 70 2. The display reads ‘off’. Standard Identification Announcement A standard announcement "Hello this MASTERCALL" is played to the receiving party on answering a diverted call. To Enable The Standard Identification Announcement (from the Keypad): 1. Press 81. 2. The display reads ‘on’.
__________________________________________________________________________________________________ SYSTEM CONFIGURATION CODES Using either the MASTERCALL Keypad or by Remote Control, enter System access code * 67 03 #, listen for "Please enter command" COMMANDS * nn where nn is option code number n = entry # = scroll down to next option number * * = abandon (do not save any changes) * # = store (save any changes) After either storing or abandoning program changes you can continue to make other programming
__________________________________________________________________________________________________ AUTO REDIAL Redial if diversion number is busy Connect if diversion number is busy * 69 DIAL TONE DETECT 5 sec wait for dial tone and re-loop if none 3 sec wait for dial tone (blind dial) Band width limited dial tone detect * 70 CONTINUOUS TONE DISCONNECT Keep connection on continuous tone Disconnect on continuous tone * 71 LINE TEST FOR DISCONNECTION Loop break every 10 seconds of silence No loop break
__________________________________________________________________________________________________ SCREENED CALL DIVERSION Off On * 83 1 2 "83 is n, please enter command" 1 2 Notes: • Factory defaults are underlined. These can and should be changed to suit particular applications. • *67709600#sets all options to the factory default, the MASTERCALL responds "Thank you, please enter command".
__________________________________________________________________________________________________ TONE DETECTION AND AMPLIFIER CODES Using either the MASTERCALL Keypad or by Remote Control, enter Tone Detection access code * 67 05 #, listen for "Please enter command" COMMANDS * nn nnn = # = ** = *# = where nn is tone parameter code number entry scroll down to next tone parameter abandon (do not save any changes) store (save any changes) After either storing or abandoning program changes you can continue
__________________________________________________________________________________________________ AMPLIFIER PARAMETER CODE DEFAULT VALUE Entry RESPONSE WAIT FOR DIAL TONE IN SECONDS * 16 005 (seconds) "16 is nnn, enter command" DTMF Tx LEVEL * 17 000 (flat) "17 is nnn, enter command" SPEECH CONNECT SENSITIVITY - Transitions prior to valid ring tone * 18 005 (transitions) "18 is nnn, enter command" SPEECH CONNECT SENSITIVITY - Accumulated signal length of transitions in ms/32 * 19 018 (ms/32) "19 is nn
__________________________________________________________________________________________________ SECTION 4 - DESCRIPTION OF OPERATION MASTERCALL is a call redirection unit capable of dialling out a preset number. Tone and line current detection is provided in software to determine when a call has been answered. MASTERCALL then connects the incoming call to the answering party. The lines are released when both parties hang up.
__________________________________________________________________________________________________ SECTION 6 - GENERAL PROGRAMMING SUMMARY Divert activate/deactivate Check first diversion number Check second diversion number Change first diversion number Change second diversion number Enter hash (#) Enter star (*) Enter dialling pause Check call counter Reset call counter 1 2# 5# 2 nnnn nnnn # 5 nnnn nnnn # ## ** *# 3 3* Check second call counter Reset second call counter 6 6* Deactivate diversion anno
__________________________________________________________________________________________________ Select first number Select second number Select third number Select fourth number Select fifth number Select sixth number Select seventh number Select eighth number 41 42 43 44 45 46 47 48 Battery off EPROM version number Disconnect power then # 2288 # * 48 # Forced disconnection Amp down Amp up # 59 # # 66 # * 66 # Enable keypad Disable keypad * 3333 # # 3333 # Store or change PIN * # pppp # Access
__________________________________________________________________________________________________ SPECIFICATIONS AMPLIFIER Frequency Range Input - Output Impedance Return Loss Insertion Gain Output Level Noise Method of operation 300 Hz to 3.4 kHz (-3dB). 220 ohm + (120 nF // 820 ohm) (complex). > 17 dB, 300 Hz to 3400 Hz. 20 dB +/- 2 dB maximum. -10 dBm → 0 dBm programmable. < -50 dBm unweighted, 300 Hz to 3.4 kHz. Software controlled AGC with noise discrimination.
__________________________________________________________________________________________________ GENERAL Power Input 12 → 48 V dc (nom.) (12 V 750 mA power adaptor supplied. Power Consumption Stand-by 30mA (350 mW) @ 12 V Operating typically 450 mA (5W) @ 12 V. Remote Control ‘Touch Tone’ DTMF telephone or encoder, with Talk-back. Telecom Connection Mode 1 (parallel) or mode 3. Enclosure Desk Top Powder coated, metal enclosure. Dimensions W350mm x D240mm x H25 - 60mm.
__________________________________________________________________________________________________ FACTORY OPTION CODES Using either the MASTERCALL Keypad or by Remote Control, enter Factor y master access code * 67 7096 50 #, listen for "Please enter command" COMMANDS * nn where nn is option code number n = entry # = scroll down to next option number * * = abandon (do not save any changes) * # = store (save any changes) After either storing or abandoning program changes you can continue to make other prog
__________________________________________________________________________________________________ SCREENED CALL DIVERSION DESCRIPTION The ‘Screened’ Call Diversion feature allows callers to hang up during or after the Recorded Voice Announcement should their call not be of an urgent nature. In this case, Mastercall hangs up and does not complete the diversion.
__________________________________________________________________________________________________ MASTERCALL MC-4044 SERIES 5 SUFFIX SELECTION - AUTO ATTENDANT Mastercall greets callers with your own announcement (up to 32 seconds) requesting a digit1 to 8. When the caller makes a selection by dialling a digit (1 to 8), Mastercall dials the corresponding number and establishes the connection.
__________________________________________________________________________________________________ EIGHT NUMBER TRY Check first diversion number Check second diversion number Check third number Check fourth diversion number Check fifth diversion number Check sixth diversion number Check seventh diversion number Check eighth diversion number 21 # 22 # 23 # 24 # 25 # 26 # 27 # 28 # Change first diversion number Change second diversion number Change third diversion number Change fourth diversion number Chan
__________________________________________________________________________________________________ EIGHT NUMBER SELECT FUNCTION COMMAND Check first diversion number Check second diversion number Check third number Check fourth diversion number Check fifth diversion number Check sixth diversion number Check seventh diversion number Check eighth diversion number 21 # 22 # 23 # 24 # 25 # 26 # 27 # 28 # Change first diversion number Change second diversion number Change third diversion number Change fourth
__________________________________________________________________________________________________ TONE DETECTION CODES Using either the MASTERCALL keypad or by Remote Control, enter Tone Detection access code * 67 05 #, listen for "Please enter command" COMMANDS * nn nnn = # = ** = *# = where nn is tone parameter code number entry scroll down to next tone parameter abandon (do not save any changes) store (save any changes) After either storing or abandoning program changes you can continue to make other
__________________________________________________________________________________________________ MASTERCALL™ REMOTE RADIO STATION MONITOR Description The Mastercall Remote Radio Station Monitor provides media market observers with remote access to radio station broadcasts for monitoring purposes. Standard telephone dial-up access is used to establish a connection to the radio station broadcast audio. Connection • • • Line 2 of Mastercall is connected to the telephone line.
__________________________________________________________________________________________________ MASTERCALL MC-4044 SERIES 5 ALARM DIALER Mastercall can be configured to operate as an intelligent Alarm Dialer. A normally open (NO) voltage-free relay contact closure is used to trigger Mastercall to dial up to eight different telephone numbers until one is answered. When answered, Mastercall plays the personal recorded message to the called party.
__________________________________________________________________________________________________ MASTERCALL MC-4044 SERIES 5 DIVERTING FACSIMILE CALLS Mastercall can be configured to divert fax calls. The following changes from the default settings are required: *6703# *81 2 *# *6705# *01 020 *03 020 *23 020 *27 042 *28 042 *29 038 *# For further information, contact Design Two Thousand Pty Ltd Design Two Thousand Pty Ltd Telephone: +613 9758 5933 Facsimile: +613 9758 5560 Email: gen@design2000.com.
