Instructions / Assembly

ManualsBrandsMasterbuilt ManualsOutdoorsElectric Slow Smoker

Masterbuilt Manufacturing, Inc.

1 Masterbuilt Ct.

Columbus, GA 31907

Customer Service 1-800-489-1581

www.masterbuilt.com

Manual Code: 9807100051 011212-04JH

Approximate assembly time : 10 minutes

CARBON MONOXIDE HAZARD WARNING

Burning wood chips gives off carbon

monoxide, which has no odor

and can cause death.

DO NOT burn wood chips inside homes,

vehicles, tents, garages or any enclosed areas.

Use only outdoors where it is

well ventilated.

This manual contains important

information necessary for the proper

and safe use of this unit.

Read and follow all warnings

and instructions before using

smoker and during use.

Keep this manual for future reference.

Some parts may have sharp edges;

handle with care.

Failure to follow these warnings and instructions properly could result in personal injury or death.

ASSEMBLY, CARE & USE MANUAL

WARNING & SAFETY INFORMATION

COLD SMOKER MODEL 20070112

THIS PRODUCT IS FOR OUTDOOR USE ONLY

Tools required for assembly: Phillips Head screwdriver, Wrench

Summary of content (8 pages)

PAGE 1
ASSEMBLY, CARE & USE MANUAL WARNING & SAFETY INFORMATION Masterbuilt Manufacturing, Inc. 1 Masterbuilt Ct. Columbus, GA 31907 Customer Service 1-800-489-1581 www.masterbuilt.com Manual Code: 9807100051 011212-04JH COLD SMOKER MODEL 20070112 THIS PRODUCT IS FOR OUTDOOR USE ONLY Approximate assembly time : 10 minutes Tools required for assembly: Phillips Head screwdriver, Wrench CARBON MONOXIDE HAZARD Burning wood chips gives off carbon monoxide, which has no odor and can cause death.
PAGE 2
GENERAL WARNINGS AND SAFETY INFORMATION READ ALL INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed including the following: • For outdoor use only. Do not operate in an enclosed area. • Unit MUST be on the ground. Do not place unit on tables or counters. Do NOT move unit across uneven surfaces. • Do not lift unit by lid handle. • Do not plug in cold smoker until fully assembled and ready for use. • Use only approved grounded electrical outlet.
PAGE 3
TROUBLESHOOTING GUIDE SYMPTOM Power light wont come CAUSE POSSIBLE SOLUTION Not plugged into wall Check wall connection House fuse or Ground Fault Cir- Make sure other appliances are not cuit Interrupter (GFCI) tripped operating on the same electrical circuit. Check household fuses or reset (GFCI) Unit malfunctioning Contact Masterbuilt at 1.800.489.
PAGE 4
IMPORTANT FACTS ABOUT USING COLD SMOKER LET’S GET STARTED! • The cold smoker is a smoke generating accessory and is intended for use with Masterbuilt TM Smokers. • This is a smoke generator. Allow sufficient time for smoking. • This unit is for OUTDOOR USE ONLY. • “Pre-season” the smoker that the cold smoker is attached to prior to first use. See page 11. • Store cold smoker in a dry area after use.
PAGE 5
HOW TO CLEAN COLD SMOKER STOP DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts Call: MASTERBUILT Customer Service at 1-800-489-1581. PARTS LIST ALWAYS MAKE SURE UNIT IS UNPLUGGED AND COOL TO THE TOUCH BEFORE CLEANING AND STORING. 2 Fig. A Remove ashes from ash tray (6) once unit and wood chip embers have cooled. 3 1 10 Remove ash build up, residue and dust with a damp cloth from ash tray (6) and inside cold smoker body (10). 6 4 10 5 9 6 Fig.
PAGE 6
ASSEMBLY ASSEMBLY • BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY. • ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE. STEP 1 Align lid handle (2) with holes on the side of cold smoker lid (1) and secure with phillips head screw (A). 2 A 1 UNIT IS NOW READY FOR USE. STEP 2 Screw adjust stabilizing legs (8) into base of cold smoker body (10). Do not fully tighten as they will need to be adjusted in the next step. 10 For tantalizing recipes and cooking tips visit us online at: 8 5 www.dadgumthatsgood.
PAGE 7
ASSEMBLY ASSEMBLY STEP 3 Insert ash tray (6) into cold smoker body (10) as illustrated. 4 STEP 9 Place wood chip tube (4) inside cold smoker body (10), nesting onto inside ledge of the cold smoker body (10). 10 10 6 STEP 10 Once chip tube (4) is properly installed remove chip tube cap (3) and fill with wood chips. STEP 4 Insert mount hook (7) through hole of bracket in mount tube (9). 1 Reset chip tube cap (3) over chip tube (4). Close cold smoker lid (1) before turning power on.
PAGE 8
ASSEMBLY ASSEMBLY STEP 7 Tighten wing nut (B) on mount hook (7) until mount tube (9) is snug to smoker body. (*Some parts not shown for clarity.) STEP 5 Align cold smoker mount tube (9) to wood chip loading port of smoker. 9 9 Insert mount tube (9) and mount hook (7) into smoker wood chip port. 7 B (Smoker sold separately) STEP 6 Place mound hook (7) on the inside lip of smoker unit.